Thank you for showing us this very fine tutorial on Schottky diodes. I already know how to test this one but kept watching your video till the end because I expected you to drop helpful tips. It was worth the time. I learnt important information about peak reverse voltage and how this particular series of diodes are named. I'm sure your explanation on how to use ohms range to test it in the absence of diode mode on the multimeter would be helpful for a lot people. What makes this tutorial special is that you put some effort to show us where each pin of the diode is connected in a real circuit board. I don't mean to criticize anyone but I find this important aspect neglected on many tutorials. It's easy to learn how to test something when it stands alone. But when it's inside the network, things become dark and cloudy. I hope you'll keep us entertained with more tutorials like this one. Thank you!
Resp Sir! Thank U Very Much Sir. Ur Advice Iam Followed Sir. Dell 6 & 4Pin SMPS Now PS on Ok 5V, and 12V was Directed Pass on at 6Pin, 4Pin and Powergood Not Out and Green and Black Connected after Comming the PG 5V Sir. Which Problem Sir and Series Lamp 3Times OFF ON, Off On Sir after Full Off. after above Problem Sir. Pls Advice Sir. -- ChinnaRao, Paderu, Visakhapatnam Dist, Andhra Pradesh.
Thank you kindly, I'm working on an smps from a power speakers, some of the diodes get about .5v one way and 2.5v the other way , they are US1D and RS1D, I have some spare PCB's and I found some ES1D on it, same voltage and amperage and Vf , can I harvest them? also, all the caps on the low side that are rated 470µf, are reading 430 to 440µf, is that close enough or do they need to be replaced? thank you again. The original problem was I was getting power to the primary, but nothing after that. I accidentally shorted the rectifier while testing and waiting on replacements, but that was I got before the magic smoke. thank you again.
Hi again my only question my shottsky Diode 3 pin when in cct the anodes are connected forward bias so it reads continuous so when removed from cct it is open cct betwwn the anodes which is correct. I have one where anodeswhich reads open in cct. I think one is faulty. Please advise. Thank you
very helpfull. i have mbr20100ct, when test in diode mode its show normal. but when use ohm its value is small and when check the right and left pin it give ohm and back to ol. is it bad one?
dear haseeb sir, on diode mode my uf shotky diode shows normal value but on ohms range i am getting mega ohms reverse biased while testing on table ,is it normal? but it somehow works on circuit board. i have no idea.. please help me understand
if you have ohm mode in your dvm then it is ok to verify the diode in forward and reverse direction. the same in ohm mode you may check the function same as in diode mode
thanks a lot CTB-34M is center-tapped Schottky Barrier Diodes (Center-tap) center pin is cathode, with heat sink it is 40V 30 Ampere while CTB-34 is 40V 15 Ampere
I have a Dr Meter PS 3010-F 30v 10a bench power supply. It won't produce any output. Every once in awhile it will come on but the LEDs for the current and voltage flash off and on and there is an surface mount LED on the board that is on but it pulses from bright to dim. I've checked these and I think they are good. What could be the issue. Can't find anything on repair. Please help I can't afford a new one and need it asap.
it means your smps controller ic is not receiving feedback. please cehck the secondary section for any short or leak capacitor or short diode rectifier check tl431 circuit might be some over voltage or over current protection is interrupting the circuit
@@HaseebElectronics ok thank you. So do heat sinks usually registrar voltage? Mine reads 172.5 and I accidentally grabbed it that's how I figured to put a multimeter on it. I'm literally learning electronics so be easy on me. I may film a short video and post it. I'm willing to trade 3D graphics or 2D graphics to anyone who can help me with this. I know time is money and I'm out of both but I am a good 3D artist and can trade.
Worth watching video. Thank you very much. Are there any two terminal schottky diodes? Which diodes are used in the output circuit of SMPS transformer?
@@HaseebElectronics Thank you for replying on my comment fast. That's unfortunate I bought it hoping that I can replace the broken diode but having a second thought that it might not work and will result to damage the other component. So I asked you. Again thank you.
@@HaseebElectronics hello again my friend. I tried it but the result is unexpected. All components are working fine but when test the output voltage I only got 12v instead of 20. So maybe that diode is for 12v only.
mbr1010 is 10 ampere 1000 volt bridge rectifier . if you are asking for bridge rectifier then use MBR1510 or MBR2510 MBR10100 is Schottky rectifier. if you are looking for MBR10100 then you can use MBR10200, or MBR15100
hello sir, i have a STPS3045CT dual schottky rectifier, and i got 0.101v voltage drop on each to pin, and no reading in reverse, is 0.101v voltage drop normal? thank u
no rfu20tm5s is recovery diode. that have only one diode inside. center pin is cathode, and outer both pins are Anode pins. outer both pins are connected to each other.
AOA sir main ne 10 amp battery charger repair kia Hy ab dc capacitor pe 14 v out ho rahy hen Lekin output leads pe ni Kahan pe issue ho skta Hy plz repy
Hi! Where may I find in my MOSPEC S20C40C Datasheet , the normal drop voltage between anode and cathode??? This, when you are measuring the component apart from the circuit. I have a reading of o.167 aprox in both sides. Greetings!
datasheetspdf.com/pdf-file/366136/MospecSemiconductor/S20C40/1 black lead of ohm meter at center pin (Cathode K) to both outer pins (Anode Pins by connecting Red Lead) it is normal reading, because it is Schottky Barrier Rectifier by reversing the test leads multimeter should display OPEN
@@HaseebElectronics it displays open luckily. May I change the entire 3 components of the heatsink independently if they are ok or not? Or maybe just the broken ones?
@@HaseebElectronics thank you! Also, I was wondering, is there any tester or maybe a homemade tool , to connect the power supply to this tool and then the tool to the wall supply (220v in my case)??? So that, to prevent the ATX power supply blow up if anything is bad fixed.
Best description of how a Schottky diode works that I have ever seen.
Thanks
best regards
Wow so beautiful wow 💖💖 Bhai ji ap ke video bohut ache hote ha
Thanks for explanation of 20 / 100v for future reference most don't explain that part!
You're welcome! best regards and special thanks
Nice informative video.I also check schottky dual diode just like your way of testing.Bhout shukria Bhai jazakAlla.
Mashaallah very Detailed information shared by you
Walekum assalam mashallah
Very informative and helpful video
Thanks for sharing dear brother
Big like...
Thank you for showing us this very fine tutorial on Schottky diodes. I already know how to test this one but kept watching your video till the end because I expected you to drop helpful tips. It was worth the time. I learnt important information about peak reverse voltage and how this particular series of diodes are named. I'm sure your explanation on how to use ohms range to test it in the absence of diode mode on the multimeter would be helpful for a lot people. What makes this tutorial special is that you put some effort to show us where each pin of the diode is connected in a real circuit board. I don't mean to criticize anyone but I find this important aspect neglected on many tutorials. It's easy to learn how to test something when it stands alone. But when it's inside the network, things become dark and cloudy. I hope you'll keep us entertained with more tutorials like this one. Thank you!
nice video sir
Like 15 walkum aslam nice information
This guy deserves an award
i am thankful for your valuable words
Sure ❤
thank you, master.. its amazing, you teach us every component.. and make it so easy to understand.. thank you so much
You are very welcome
very informative video great sharing stay blessed..........
I have been looking for this so long now ...thx Sir ..you r my best teacher
Big like very nice video 👌👌
Thanks for sharing this valuable and informative vedeo 👌👍👍jazak Allah khair 😍
Wow awesome mashallh very nice informative vedio big like my dearest brother well done.be happy ameen best wishes.
Excelente dica meu amigo.
Parabéns por compartilhar conosco seus conhecimentos. Obrigado
o prazer é meu
obrigado por escrever suas belas palavras
Thanks Sir, amazing great video idea channel I like it blessed
Very good 🌹👌👌👌👌
Nice video wonderful
Selamat malam boss, sukses terrus video2 nya...
I guess it is kind of off topic but do anybody know of a good site to watch new series online ?
@Nico Christopher flixportal :D
@Tyson Neil Thank you, I went there and it seems to work :) Appreciate it !!
@Nico Christopher happy to help =)
Man you are an awesome teacher.
best regards and special thanks
Very nice awesome informative video. Thanks sir.
Most welcome
Nice test tutorial
Good job Haseeb
عيد مبارك
Thank you very much for your support, Congratulations.
it is my pleasure
please accept my best regards
amazing vlog. thanks for sharing. keep it up. stay connected. stay safe and healthy.
Nice upload thanks for sharing my friend
Resp Sir ! Super Vedio Sir. Thank You Sir. -- ChinnaRao Visakhpatnam , AP
best regards
Resp Sir! Thank U Very Much Sir. Ur Advice Iam Followed Sir. Dell 6 & 4Pin SMPS Now PS on Ok 5V, and 12V was Directed Pass on at 6Pin, 4Pin and Powergood Not Out and Green and Black Connected after Comming the PG 5V Sir. Which Problem Sir and Series Lamp 3Times OFF ON, Off On Sir after Full Off. after above Problem Sir. Pls Advice Sir. -- ChinnaRao, Paderu, Visakhapatnam Dist, Andhra Pradesh.
Oooh very nice upload
...Gained alot of info..Keep it up❤️🤩😍
NYC upload
Belle vidéo, beau électronique, bon minutes de joie,
trés bien mon ami Hasseb,
thanks, your help allowed me to fix my kuka robot.
it is my pleasure
wish you best of luck and huge success in your life
Very detailed information given by you ... Thumbs up from my side
أتمنى لكم النجاح 🌹🌹والتوفيق 👈👈👈
Thank you kindly, I'm working on an smps from a power speakers, some of the diodes get about .5v one way and 2.5v the other way , they are US1D and RS1D, I have some spare PCB's and I found some ES1D on it, same voltage and amperage and Vf , can I harvest them? also, all the caps on the low side that are rated 470µf, are reading 430 to 440µf, is that close enough or do they need to be replaced? thank you again. The original problem was I was getting power to the primary, but nothing after that. I accidentally shorted the rectifier while testing and waiting on replacements, but that was I got before the magic smoke. thank you again.
Thanks very nice can’t use 2 diode for replacement this device ??
Yes you can 2 schottky in place of this one
Thanks for sharing such informative video. Lots of love to your kids from their fufi jaan
hi, do you have a vidio showing how to test capacitors ? i did not see one on your utube page thanks
please check 149 and 428.
Thank you i learn about them today
it is my pleasure
Very interesting stuff... complicated! Loved watching
Great share information step by step
Is this the same as Mbrf2080CTL and MBRF2060CTL? My Samsung LCD TV no longer powers on and technician said to buy these two component.
Big like to you my good friend 😁
Thank you very much for the info!
It reminds me the schematic of the pnp transistor on your previous video about transistor identification.
Jazakumullah khairan katsiiran
hi hanks excellent explanation ! Ill put it to good use
Great video
It is my pleasure 💕
very good bro 👍
Thanks for sharing this amazing tutorial on function and testing of rectifier 👍♥
Stay safe
So clever thanks for this
Hi again my only question my shottsky Diode 3 pin when in cct the anodes are connected forward bias so it reads continuous so when removed from cct it is open cct betwwn the anodes which is correct. I have one where anodeswhich reads open in cct. I think one is faulty. Please advise. Thank you
for my transformer, I have Two AC side without center tapped one. So how can I use this schottkey diode configuration for rectifying DC output?
Great video,I have HBR20200 doe s this mean HBR20100 cannot be used.
Thank for sharing my dear great job 👍
very helpfull.
i have mbr20100ct, when test in diode mode its show normal. but when use ohm its value is small and when check the right and left pin it give ohm and back to ol. is it bad one?
it is schottky rectifier,
its forward resistance and forward diode drop voltage are less than silicon rectifier.
it is normal indication
+super like+super favoritado,só vídeo top de linha, ai sim em,parabéns, excelente canal 62
*good*
Good shearing
dear haseeb sir, on diode mode my uf shotky diode shows normal value but on ohms range i am getting mega ohms reverse biased while testing on table ,is it normal? but it somehow works on circuit board. i have no idea.. please help me understand
if you have ohm mode in your dvm then it is ok to verify the diode in forward and reverse direction.
the same in ohm mode you may check the function same as in diode mode
gracias muy buen video solo preguntarle como conectar los diodos y donde para darle mas amperaje a la salida de -12vdc de fuentes atx de computadoras,
Salaamu Aleikum, please could 20U150 a schottket Diode be tested in the same was as NBR20 100?
Both are same
Test is same
great video , thanks I am learning so much! What about CTB34M ( 78 02) component replacement? is it the same as MBR?
thanks a lot
CTB-34M is center-tapped Schottky Barrier Diodes (Center-tap)
center pin is cathode,
with heat sink it is 40V 30 Ampere
while CTB-34 is 40V 15 Ampere
I have a Dr Meter PS 3010-F 30v 10a bench power supply. It won't produce any output. Every once in awhile it will come on but the LEDs for the current and voltage flash off and on and there is an surface mount LED on the board that is on but it pulses from bright to dim. I've checked these and I think they are good. What could be the issue. Can't find anything on repair. Please help I can't afford a new one and need it asap.
it means your smps controller ic is not receiving feedback. please cehck the secondary section for any short or leak capacitor
or short diode rectifier
check tl431 circuit
might be some over voltage or over current protection is interrupting the circuit
@@HaseebElectronics ok thank you. So do heat sinks usually registrar voltage? Mine reads 172.5 and I accidentally grabbed it that's how I figured to put a multimeter on it. I'm literally learning electronics so be easy on me. I may film a short video and post it. I'm willing to trade 3D graphics or 2D graphics to anyone who can help me with this. I know time is money and I'm out of both but I am a good 3D artist and can trade.
si conduce el pin 1 y el 3 (con el MBR 5U100) npn-pnp va indicar que esta en corto?
Worth watching video. Thank you very much. Are there any two terminal schottky diodes? Which diodes are used in the output circuit of SMPS transformer?
No two terminals skohtty, the are just called diodes at that point. The 3 are are high speed rectifier diodes
It depends on the PSU. Or inverters your working on. Plenty of different types of diodes and Mosfet bridge rectifier and rectifier diodes ECT.
Thanks for sharing
Wonderful tutorial
Super 👍✔️
Thaks sir.. For tutorials❤
Very good 👍🏻
it is my pleasure
Merci je cherchais justement comment les vérifiées vs êtes d'un grand secourt , il me semble qu'il y a pas d'équivalent autres que cette marque .
Oooo very useful video thanks a lot 😊 ❣️
Mantap 😊👍 bos kuuuuuuu
Lyk forty two, nice informative tutorial .
Hello I need around 12 volt 80 amp mbr but can't find anywhere ..can i parallel two 40 amp mbrs to achieve 80 amp capacity??
Yes you can
Muchas gracias, excelente
best regards
Hello my friend. I want to ask if can I replace MBR20100CT with MBR2045CT? or should I need MBR20150CT? Thank you.
we cannot replace mbr20100 with mbr2045 as 2045 is 45 volt only. you can select any voltage value above than 100
@@HaseebElectronics Thank you for replying on my comment fast. That's unfortunate I bought it hoping that I can replace the broken diode but having a second thought that it might not work and will result to damage the other component. So I asked you. Again thank you.
@@HaseebElectronics hello again my friend. I tried it but the result is unexpected. All components are working fine but when test the output voltage I only got 12v instead of 20. So maybe that diode is for 12v only.
it seems there is problem in switching and feedback circuit. diode have to rectify whatever it will receive
Excelent, god bless u
thanks a lot
Same way of testing on MUR1640CA?
Hello Bhai 🙏 Eid Mubarak ho aap sab ko advance main 🙏
thank you, barakallah..
special thanks
best regards
very nice my friend
The X4202S is not availavble, may i use the mbr2040 instead?
No
X4202S is 20 ampere 200V fast recovery freewheeling diode
while MBR2040 is 20 Ampere 40V is a schottky rectifier
so it will not work
How to find equivalent for MBR1010 shottsky.thank you
mbr1010 is 10 ampere 1000 volt bridge rectifier . if you are asking for bridge rectifier then use MBR1510 or MBR2510
MBR10100 is Schottky rectifier. if you are looking for MBR10100 then you can use MBR10200, or MBR15100
جزاك الله خيرا
thanks a lot. stay blessed
Great work 👌
Great Job man!
best regards 💕
good video mi frend no bady explein in homs hallo from mexico
best regards
hello sir, i have a STPS3045CT dual schottky rectifier, and i got 0.101v voltage drop on each to pin, and no reading in reverse, is 0.101v voltage drop normal? thank u
Yes dear
It is normal indication
@@HaseebElectronics thank u very much sir... im learning a lot on your videos... keep uploading... god bless you more!
God of electronic
thanks a lot. best regards
Mbr3045st ki jagah aur kaun sa diode lagaye sir
Can you tell me that SBR AND MBR difference Thanks
How about rfu20tm5s.....its same with this video.....how i know this transistor good or bad
no rfu20tm5s is recovery diode. that have only one diode inside. center pin is cathode, and outer both pins are Anode pins. outer both pins are connected to each other.
AOA sir main ne 10 amp battery charger repair kia Hy ab dc capacitor pe 14 v out ho rahy hen Lekin output leads pe ni Kahan pe issue ho skta Hy plz repy
MBRB10100 same measuring?
good 🤝
Da hora tenente
Very well sir
thanks a lot
slaam walikam khan sahab
wa alaikum salaam bhai ji
@@HaseebElectronics i have made an electric car.want to consult you to upgrade it
@@HaseebElectronics sir can i check mbr20150 in the same way
Hi! Where may I find in my MOSPEC S20C40C Datasheet , the normal drop voltage between anode and cathode??? This, when you are measuring the component apart from the circuit. I have a reading of o.167 aprox in both sides. Greetings!
datasheetspdf.com/pdf-file/366136/MospecSemiconductor/S20C40/1
black lead of ohm meter at center pin (Cathode K) to both outer pins (Anode Pins by connecting Red Lead) it is normal reading, because it is Schottky Barrier Rectifier
by reversing the test leads multimeter should display OPEN
@@HaseebElectronics Thank you!!
@@HaseebElectronics it displays open luckily. May I change the entire 3 components of the heatsink independently if they are ok or not? Or maybe just the broken ones?
yes you can do it. if anyone is bad or short
@@HaseebElectronics thank you! Also, I was wondering, is there any tester or maybe a homemade tool , to connect the power supply to this tool and then the tool to the wall supply (220v in my case)??? So that, to prevent the ATX power supply blow up if anything is bad fixed.
hi, do i need to remove it from the board to test it? thanks
it is better to remove and test it outside to eliminate the problem