QS-S4 Pre Program Settings | Beginners Guide! + Tips | Blade 10 | James Angelo TV | Vlog.73
HTML-код
- Опубликовано: 25 июн 2021
- Take note: Damao display & Qss4 are same p-settings.
Pre program settings ( P-SETTINGS )
P-settings allow scooter riders to customize their ride.
HOW TO ENTER:
1. Power on scooter.
2. Press and hold Power + Mode buttons.
3. Press Power button to toggle through P-settings.
4. Press Mode button to adjust values.
PO1 : lcd brightness level (1,2,3 )
P02 : Mileage display in km or mile
P03 : Voltage level of machine ( 24,36,48,52,60,72 volts )
P04 : 1-60 mins before machine goes to sleep in activity
P05 : N/A
P06 : Wheel diameter in inches
P07 : No. of magnets on motor ( 28 for blade 10 ) 30 is default
P08 : Power level (0-100)
P09 : Zero start or Kick start ( kickstart for begginners )
P10 : N/A
P11 : Electronic braking on or off
P12 : Soft or high acceleration ( 1 is softest 5 is highest torque )
P13 : N/A
P14 : N/A
P15 : Controller cut off voltage
P16 : Zeroing of odo ( this will in very less odo and 1 time reset only )
P17 : Cruise mode ( do not use cruise control if your beginners )
P18 : N/A
P19 : N/A
P20 : N/A
PLEASE LIKE,SHARE ,SUBSCRIBE TO MY YOU TUBE CHANNEL!!
➡ Facebook / jamesangelo.caunca.5
➡ RUclips ruclips.net/channel/UCqPe...
OTHER RELATED VIDEOS:
range test part 1 ➡ • Blade 10 Evo | Range T...
blade 10 evo break in ➡ / vvmpwa-mzw
Blade 10 EVO Unboxing ➡ • Blade 10 EVO (2021)| U...
blade 1o evo specs & features. ➡ • Blade 10 EVO🔥 | Top SP...
UNBOXING & COMPARISON OF BLADE 10s & BLADE 10d ➡
• UNBOXING & COMPARISON ...
#QSS4psettings#blade10#propersettings
Blade z ➡ • BLADE Z🔥| BEAST!! ELEC...
Top Speed Test ➡ • Blade 10 EVO🔥 | Top SP... 
Хобби
Great video mate. Very helpful.
Thanks 👍
thanks bro
Your content is so touching
thank you bro
so touching for an excellent video
thanks bro appreciated 🙏❤️
Its so helpful that i learned the programming of e scooter and I really need to learn about this thank you🎉
thanks bro appreciated
Nice one master!
paps salamat sa milk tea 🙏❤️
@@JamesAngeloTV welcome paps, sa uulitin 😉👍
now i know lods. good job bro very helpful video🙏
thank u lods❤️
Saludos estoy a punto de que me entreguen mi blade 10 pro 2021 algún consejo antes de recibirlo?
thanks for video. i need to enable that cruise control
welcome bro appreciated 🙏
Thank you bro😅😅 hehehe its very helpful
thanks bro
Nice setting ng kind if scooter
maraming salamat po❤️🙏
👍🏼🤗. But zero9 motor magnets nr? 🙏🏼Thenks for great video🎉🤗
Can you make video for error
Tnx paps na adjust q blade 10 q
wc paps ride safe
Is it possible to reprogram the display to work with another scooter with more power? Just changing the settings from 36V to 72V? changing P03, P06, P07 and P15 did not help and the E10 error still occurs. Thank you
display program depends on controller program, if not compatible it will make error
need you to do a tuturial review on the evercross H5 Electric Scooter Please make a tutorial ..Great Content Salute..
i will try bro thanks for your suggestion
Question.. my speedometer function displays numbers that get very high (upto 99). Neither miles not kilometers per hour! Any way to fix this?
some display is like that only 99kmph there nothinh wrong about that because mostly the speed of blade 10 is 75kmph gps
Hey I need help with my fluid free ride horizon I was changing the p settings and I messed everything up and I’m trying to reset the settings but I don’t know how is their a way to factory reset someone pls tell me
what is your lcd bro?
Would you happen to know what the motor magnet count is for a YUME M11H 72v 3500watt dual motor for 7000watt total.
30 same with my kaabo gt pro
top
tkanks bro
I have a quick question. Am I able to change the cut off voltage on my scooter in order to make it ride longer at lower voltage?
no bro not possible because it can cause damage / drain your battery
@@JamesAngeloTV thank you
@big45ent eidesafe bro
Hi ,i have a winner sky scooter its battery dies on each 15 klms distance after full charge ,is that normal or it has problem? Please answer me ,thanks sir
how many ampere an hour? AH your battery?
Is there any way to reset all the settings? I can't seem to find a way to go down on the wheel diameter
no bro no reset for this throttle
@@JamesAngeloTV oh darn. Well alright then. Thanks for letting me know!
I wish there was a setting for using either the front or the back motor because my scooters back motor isn’t working properly and gets jammed when you add power to it. But my front motor works fine and now I can’t use it because of the back motor.
that is hall sensor issue, check the connection
Tengo problemas técnicos no camina nose como configurar la pantalla
bro please english
please the PAS is not working with this controller ? what is the reason , i used 3 different pas and not working , thank you
bro sorry what do you mean by PAS?
@@JamesAngeloTV pedal assist , many thanks
bro just wanna ask, do you happened to know what is the exact cutoff voltage for zero 10x 52v 23a model?
42.8 volts 5% 42 is drop. for 52volts
@@JamesAngeloTV you're the best mate, i really appreciate your time, thank you very much, keep safe, God bless!
@@racismitsstopswithme7444 wc bro ridesafe
Sir question, my e10 odometer is 2km only, wont go up. Someting from settings can fix it???
2 kmph ang speed? o range na 2 km
Yung odometer sira sir, 2km lng hnggang ngyn kht ginamit na sa malayo, sa speed wala naman issue sir, pano kya ma fix yun sir
Hi what could be the reason when I get error code 06? I don't have any throttle when this error comes up. Could you please help me?
what is your scooter bro
@@JamesAngeloTV its called a buetta scooter but I think it's renamed. I have a pic of it. Maybe you would know.
This was battery not supplying enough power - it's a battery fault - you might need to replace cells, rebalance the batteries, install a BMS with a balancer, or replace the battery pack. If the batteries are old, the higher power chargers might reduce the battery life more, so you might want to reduce the charger capacity, after repairing the battery pack, to extend the life. Also try setting speed to 2 (3 has no limit, 1 is perhaps too slow but would be best) and then set the power to somewhere under 50 (usually it's 100) - eg. set power level to 20, and it's a bit faster than walking speed, and the battery might not drop out. Tested on mantis 8, controller LT-01 (like qs-04 & mr-100)
hi, is there any way to carry over total miles from old display to same new display just with thumb throttle?
do you mean you want to convert the old throtlle to thumb type?
@@JamesAngeloTV no, I want to buy a new throttle, and want to know if the total miles of the scooter (odometer) get put on the new throttle as the old one
@@ridermog if you change the display with new one it will return to zero
hi, everytime i change the P09 to kickstart it resets to zero start when i turn off and on the scoot again. how to permanent it?
what is your scooter bro? brand
@@JamesAngeloTV go board titan bro. i saw we have qs s4 :D
maybe your scoot is set for that even you change,
@@JamesAngeloTV I see, thank you for response~!
After making the Change in the P-Settings .. Allow the QS-S4 to naturally exit the Change Settings Mode by waiting a Few Seconds .. Then you can turn off the Scooter or Proceed to Scoot about !~🛴😎
Can you help me. My screen is broken and I bought a new qs-s4 but when I put it on it flashes red and it doesn't work. Can I fix it and if you can teach me. Thanks
your display is not scompatible maybe you buy from zero scooter
@@JamesAngeloTV Which one do you recommend?
it should be the same you will replace same manufacturer or serial number
@@JamesAngeloTV Is there one that fits all scooters?
Please help, such a model has an unlock code before it did not enter, the code is not 9221, please help, what is the code?
what do you mean code bro
@@JamesAngeloTV
How to reset factory
no option bro to reset.
I have E10 and how to make high speed? Please
bro just add range batt it will increase speed or add voltage and high amps controller
Hey! I bought recently a kugoo kirin x1 with a QS-S4 lcd and i dont know what happened but the first time i got to use it i got the 08 error code and i dont know how to fix it perhaps you know how to fix it? And how i can hard reset my lcd
error 8 is throttle issue
@@JamesAngeloTV so its my lcd that is broken?
@@JamesAngeloTV because somethimes it works and somethimes not
@@denzeldenhartog5538 replace new pne
@@denzeldenhartog5538 yes bro
Can you explain further about P07 no of magnets.. I have a 60v 21am, 1200x2 motors. My escooter suddenly lowered its top speed by minus 15kph. The mechanic just adjust the program and told me its about the magnets.. Then it cost me 500 pesos by just doing that. I want to learn more. Thanks in advance
standard motor magnet counting inside of motor is 30 some manufacturer they advise to use 27 for speed
we are same size of motor
P08 is not visible, how do I un-hide that option? (Joyor X5S)
sorry but no idea in that display. check the manual or contact supplier
Hello Jonas, did you find out how to access hidden P-items? Mine P8 is also hidden and it's annoying..
Bro can you post also all error codes on qs-s4 blade controller.thanks
let me check bro from supplier the error code
How can i reset it ?
if the odo is too high you cant reset
I have a ninebot es2
I want a hook to hang the groceries
Where can I get one
search in amazon bro bike accessories or go to madinat zayed
how much magnets does joyor f3 have?
sorry bro but i don’t have an idea about joyor f3
@@JamesAngeloTV okay
i have error 11 what men ? help me ! !
you have problem in rear or front controller
Hi, how to hard reset qs-s4?
is that new scooter? or old 1
@@JamesAngeloTV bought this week
honestly there is procedure to reset but supplier didn’t teach me that
Sir another question for e10 offroad, battery bar icon nya tumatalon talon, while using, 4 bar tpos 2 bar, then balik 4 bar... may gngwa sa settings pra ma fix??
magbase ikaw paps sa volt meter, kapag yan nag battery drop bms tama nian sa battery
pwede mu rin icheck kung ilan voltage level at speed level
Yung e10 namen 48v.. anung number sa P settings dpt ko icheck?
What is code for zero 10x ??
Who know code ??
what do you mean code bro?
@@korobovnation616 i saw somewhere 115 not sure
You got answer?
5252 doesn't work
Hello JAMES ITS NOTORIUS IM THE ON WHO TOLD ABOUT MY ESCOOTER SO CAN A QS-S4 THROTTLE GO ANY SCOOTER AND HOW DO YOU FIND LIMITED WIRE ON SINGLE REAR MOTOR SCOOTER YES THAS WHERE I NEED YOUR HELP ON PLEASE GET BACK TO ME THANK YOU BRO
no bro because depends on controller. example this blade 10 display not fit to zero 10 x but same qss4
Sir san po kayo nagpagawa . Ganyan na ganyan din po sakin e. Papagawa ko din po sana. Hirap mag commute. Salamat lods nag subs na po ako sa inyo
alin po pinagawa paps?
Sir Diko Po ma axis Po p sitting njax-T sir
anung name ng display
Kougoo
blade bro
May controller po kayo nyan sir
pang rear lang bro
meron ako available pang blade minimotors display
power boton
😆
Ano naman setting sa blade x eco?
same sa blade 10 damao change mu lang po yung voltage
@@JamesAngeloTV salamat boss
@@JamesAngeloTV boss ano susundin ko sa charging ung indicator sa charger pag nag green na or ung voltage indicator pag nag 54.6v na?
At ilang percent ng battery kaylangan icharge para maalagaan at hindi masira agad? Salamat
Hi, password menù?
password menu no idea bro
Can you make a video about the motor magnets
what do you meed to know about motor magnet bro
@@JamesAngeloTV does it get faster if you make the number higher?
@@Irishkiwi no bro only number in screen will increase but in actual same in gps same
@@JamesAngeloTV thanks
my scooter jonebike 3200w
open the deck check you controller maybe some wire are disconnected
Can you do a lesson on the bikydom electric scooter 🛴
I went from using the throttle to now kick starting
I FEEL LIKE TOM HANKS AND HIS SOCCER ⚽️ BALL
LIKE HELP SERIOUSLY THOUGH
need to check the settings bro based on your brand display because every display have different settings