Don't you think service/ultimate load combinations for Water pressure and Soil pressure should have dead load as well? I think if you do not add dead load, the deflections are going to be a lot more than actual.
Salam brother... Listen carefully... I have drawn wall... But it's global x is inside, y in perpendicular to wall and x,and z upwards ... Also local axis.... L3=y= blue is inside, ... Now what to do... Your was easy as all blue L3 outwards.... I tried every method but... As I run analysis... For water this side wall shows inside deflections and for soil shows outwards.... Any solution
Nice work. Keep it on. Now the question is, Do the walls and columns really take % plus and 70% minus lateral loads (quake) as per IS Code? How do you know and do make that happen? Dual system with EQx, EQy, EQz and Sprectrum Analysis as dual system. Can you help on such vidio. How do I join as I am in Nepal. No join button and didnt get / understood your advice on what you said in this vedio. Thanks. Keep up the good work.
I have learn so many things from your videos. It would be great if you make a video on how to design a shear wall when soil pressure is acting on it. I assume the same procedure can be used for shear wall that you explained in this video. In that case we will be having soil pressure only. correct me if i am wrong. Thanks jazakallah
Hi my friend you use in area spring with compression only but your analyza was linear this is wrong if you use compression only or tension only you have to use nonlinear analysis
Fixed supports will exert additional stresses on soil and the foundation must fulfill strength requirements such as moment and axial capacity and overturning resistance. Hence, we provide hinge support.
Could you please tell how to apply load in case half of the wall is in contact with soil e.g Height of wall is 10 ft and 2 ft is the free board or similarly in case of retaining wall having aheight of 10 ft soil is only present upto 6 ft height
thank you its very nice model and very useful video , my question is how to model swimming pool on the roof of building or in specific floor not on the base and kindly asking you to upload this nice excel sheet thank you very much
@@Decodebd I am designing a slab with some walls around it (3 ft tall, not super big) and was wondering how to assign soil pressure on SAFE. SAFE does not give you the flexibility to assign loads on 1/3 of the wall & also design reinforcement / rebar. Any thoughts? I'd appreciate your help.
![LAVROV's interview with Tucker CARLSON 😁 [Parody]](/img/1.gif)
U r the best of best teachers please make under ground water tank videos in SAP 2000
Thanks. In sha Allah I will do.
@@Decodebd
Hello, can you share your excel please, it will be for university use. kevindiazpinto123@gmail.com
hello sir.. I am following you past 2 years ... u r going a great job.......
Hello, do you have an excel sheet to verify the moments caused by water and soil on every different wall of this specific exercise?
Don't you think service/ultimate load combinations for Water pressure and Soil pressure should have dead load as well? I think if you do not add dead load, the deflections are going to be a lot more than actual.
I wanted one for manhole but this video made me quite clear on what things i need to change for that !
don't get it at 10:43. Why not fixed support at base?
Thank you for the detailed procedure. Waiting eagerly for the excel sheet to be uploaded soon.
Please be a member if you have the ability.
@@Decodebd If I become a member,how can I get the excel sheets???
@rakibul hassan After being loving fansub meber drop your mail address below tutorials to get resources.
@@Decodebd
please dear
i need axcel sheet.
thank you . please can you explain why you took the(surcharge load qa =12kn/m^2)
Salam brother...
Listen carefully...
I have drawn wall... But it's global x is inside, y in perpendicular to wall and x,and z upwards ... Also local axis.... L3=y= blue is inside, ... Now what to do... Your was easy as all blue L3 outwards....
I tried every method but... As I run analysis... For water this side wall shows inside deflections and for soil shows outwards.... Any solution
masyaAllah, thanks for your explanation about wall design 😇
Nice work. Keep it on. Now the question is, Do the walls and columns really take % plus and 70% minus lateral loads (quake) as per IS Code? How do you know and do make that happen? Dual system with EQx, EQy, EQz and Sprectrum Analysis as dual system. Can you help on such vidio. How do I join as I am in Nepal. No join button and didnt get / understood your advice on what you said in this vedio. Thanks. Keep up the good work.
Excellent. Thanks...
You are welcome!
Sir,? Is the CSI detailing can be used to make reinforcement detail for water tank / swimming pool case? thank you sir
SALAM SIR..
thanks for making an effective tutorial for us..
You are most welcome
Can you tell me how to find surcharge load and provide reinforcement detailing ?
Could you please provide load details as per IS code?
Surcharge load is extra load on soil for any vehicle or machineries. The weight of vehicle divided by the contributory area is surcharge pressure.
Could you please tell something about area spring and why is the value taken as 15000 in local direction 3?
Allowable displacement 3000mm/100 is 30mm....you said it is 3mm ... Is it 30mm Or 3mm allowable dispalcement
أحسنت جزاك اللَّه كل خير
Well done gazakallah keep going
Thanks
This was a very helpful tutorial sir. Thank you
I have a doubt..can you please tell me the reference of deflection limit as L/100.
Can we Design water tank also in Etabs Sir? If so then please show us one design with IS code.
Good explanation sir!
Thank you!
Welcome
Very Informative.... Shukran....
Most welcome
Thanks Sir it is very helpful
I have learn so many things from your videos. It would be great if you make a video on how to design a shear wall when soil pressure is acting on it. I assume the same procedure can be used for shear wall that you explained in this video. In that case we will be having soil pressure only. correct me if i am wrong.
Thanks
jazakallah
Need a detailed explanation in Designing of rooftop swimming pool system. Plz:-D
Hi my friend you use in area spring with compression only but your analyza was linear this is wrong if you use compression only or tension only you have to use nonlinear analysis
I have the same opinion as you. I'm not understand this one. Normally, I often assign K spring for point.
Very nice
Thanks
Awesome video sir...plz help me..i need Tuned liquid damper defined on sap 2000 &etabs...if you konw about its then plz give me fast reply...
Best explanation
Glad you think so!
In a swimming pool , the water is still. If it is a open water channel ( water is not still) will water pressure change??
how to calculate surcharge could you please tell me how
Could you please explain how to draw and modle a swimming pool, which has a combined flat bed and a sloping bed
How do you stimulate bricks masonry wall carrying cut lintel beam or sunshade slab for window / slab rest on wall like cantilever 🤔
Sir what is area springs? And what calculation you have done?
what momenets do we use for reinforcement design in both direction?
THANK YOU VERY VERY MUCH.
You are welcome!
@@Decodebd SIR CAN YOU SHARE SOIL WATER LOAD CALCULATION EXCEL SHEET..
Thank you sir.
where do I get surcharge load value? please reply my question. already I bought this resource.🙏🙏🙏
Sir..plz explain design and detailing also..as per IS code
Thank you in advance
Will try soon in sha Allah
great work sir
Many many thanks
The Best ,Thank you . May i have you exel file for study.
Thank you . Can I get the excel sheet for the earth pressure load ?
Check resource page of my website decode-bd.com
amazing video
Thank you very much
Thank you too
how can we check Reinforcement in after analyzing ??
Thank you, Sir. Sir can U elaborate In support Why U restrain Only translation x and y and not considering Rotation In this. ?
Fixed supports will exert additional stresses on soil and the foundation must fulfill strength requirements such as moment and axial capacity and overturning resistance. Hence, we provide hinge support.
great work sir...! plz upload excel sheets it will be very helpful
Could you please tell how to apply load in case half of the wall is in contact with soil e.g Height of wall is 10 ft and 2 ft is the free board or similarly in case of retaining wall having aheight of 10 ft soil is only present upto 6 ft height
To interpret SAP 2000 results: ruclips.net/video/acTHe8KMRXU/видео.html
Thank you sir
Welcome
Thank you for this video. Can you also make a video on how to design Raft/Mat foundation in Etabs
Welcome. In sha Allah, I will try.
10.41 min why are we giving restraint X, Y , why not Pin or fixed .. what difference will it make.. where we have to use pin , fixed
Thank you. In nonuniform load application why A,B,C are in kN/m3 and D is in kN/m2 ?
A,B,C represents unit weight of material like soil, water where as D is area load.
Unit of C is Kn per cubic meter (Etabs) but in excel calculation show Kn per sq. meter
would you pls explain about it
thanks in advance
At 3.5 m Pressure = kN/m2, After solving the equation, C= kn/m2 divided by m= kN/m3.
Why you assign support of wall only Translation X & Y?
Brother, Can you please elaborate on "AREA SPRING value 15000 Kn-m/m2"??? Means any particular conversion method is there for that obtained value??
I just used it as example, for proper value conversion you need to check previous tutorials.
@@Decodebd bhai which tutorial you have explained area spring value ? i cant find it out . could you share the link ?
@@mahiulhossainbappy7929 spring value will be SBCXfactory of safety/settlement allowed
Thank you, sir. Sir, Please upload the link to the excel file.
Sir why we are dividing this area into 20 and so on
Can you upload excel sheet that you have used during design...thank you
Will upload soon
Can u explain the component at shell forces sir? Especially when we read the diaphragms forces.
To interpret SAP 2000 results: ruclips.net/video/acTHe8KMRXU/видео.html
hv u shared the excel sheet which u used in tutorial ?
BECAUSE THE DEAD LOAD IS 2,0 kN /m2 IF THE SLAB HAS 350 MM? . SHOULD BE GREATER. FOR ME IS 8,4 kN/m2 (24 kN/m2*0,35).
Good Explanation with detail procedure in this software...sir can u upload the excel sheet for this...?
Will upload soon in sha Allah.
I want to get excel sheet too, how can I join sha Allah?
Why haven’t you used modifiers for wall and slab ?
Because Non-uniform pressure applying was the demonstration of this tutorial.
can i get excel sheet of this tutorial?
Bro please make a video on second beam, cantilever beam, balcony and also partial realese
Pls bro it would be very help ful to us
Will do in sha Allah
What about Uplift??
Uplift needs to be checked as well.
@@Decodebd will u check uplift in another video while u will go to detail for reinforcement
Very Nice sir, could you make videos analysis by applying water hydrodynamic or water add mass matrix in ETABS or SAP2000
, Thanks
Will try
thank you its very nice model and very useful video , my question is how to model swimming pool on the roof of building or in specific floor not on the base and kindly asking you to upload this nice excel sheet
thank you very much
Will show for that one also in sha Allah. For excel you need to be member to support the channel.
@@Decodebd I already subscribed to the channel
Join as member please. If you don't get "Join" button beside Subscribe button, then please use vpn & select country UK or US
@@Decodebd i didi its UK now
Is it possible to model the same in SAFE? Thanks
I have not tried it in SAFE
@@Decodebd I am designing a slab with some walls around it (3 ft tall, not super big) and was wondering how to assign soil pressure on SAFE. SAFE does not give you the flexibility to assign loads on 1/3 of the wall & also design reinforcement / rebar. Any thoughts? I'd appreciate your help.
Why didn't you apply point springs and edge constraints????
Because I assigned point support at edge.
@@Decodebd can you explain in detail what will happen. In point supports and point springs case, which one is better and function ?
Dada, where can I find the xls sheet or can u gide to prepare the excel sheet for varying load equation.
If you can please become a member.
@@Decodebd you mean like your page, or sign up on specific page?
Please give the option to download to all of ur video
thank you it's very interesting جزاك الله خير Can you upload excel sheet
Should we add earthquake force or not?
You can add.
so cool, can i have the exceL?
Sir please create a video on elevates swimming pool in building in etabs
ASAP in sha Allah
What about crack width check ???
Eng aslam alekom
Eng am make all prosegur but when make display for soil pressur all slab 0000 value nothing happens.
Why
Check the tutorial carefully.
can i join the grp now..is it still active?
Yes.
Asslam-u- Alikum I have joined the group, now will u plz share the excel file. Thank you in advance
Need excel sheet im member
بورك فيك ياباشا ممكن الأكسل excel
Hi M22 is vertical moment and M11 is horizontal moment
Can you share the excel file for pressure calculation? Thank you
Can you please share this Excel spreadsheet!
Thank you for your great explanation, please send me excel sheet
No reply for the excel sheet so far
sir need the excel sheet, your internet no have excel sheet. can you give me this? i will pay you.
Please send the excel file sir. Provide a download link. Thank you for the videos.
Will upload soon in sha Allah.
sir I have joined the group, now will u plz share the excel file
Thanks for joining. Give your mail address.
@@Decodebd ronniesyncin27@gmail.com
Have another question. Hope you will answer my query through mail
Thanks for being member, check mail.
plz share the excel file m
mohamedhamd48@gmail.com
you could have just multiplied the water density to the height
plz give me file for design thank you
thanks sir... could you please send me the excel sheet
Sir can I get this excel sheet
Thanks
sir can you share the sheet Excel please ?
Sir, Please share the spread sheet
Hello sir I want to learn in real. How much charges plz let me know
Hi.
how to download excel file water pressure?
Will upload soon in sha Allah.
@@Decodebd Tnx.
@@Decodebd We are still waiting!!!!!!!
can you shear me your design load file of swimming pool?
Will upload soon in sha Allah.
may i have your excel file?
Can you please share the Excel sheet