Receiving this kind of collection sort of marks a transition towards being a more serious museum, with an emphasis on institutional memory, rather than just a collection of random stuff (not that there was anything wrong with that). It will be very interesting to see how the museum evolves. It wouldn't surprise me if there are many companies that find themselves in a similar position in the coming decades.
The mechanical Tachs starting at around 9:50 are very, very useful. Jaquet made more then one type, including flyweight and timer types. They are general purpouse for use measuring ahsft speeds on motors, transmissions, machinery, etc. Usually with a set of contact tipe for getting into a 60degree machined center on a dhaft, and often with rollers for measuring surface speed (conveyor belt and the like) I still use them. The flyweight type direct read and can show speed variation, the timer type time for six seconds (usually) with a mechanical clock that engages and disengages a clutch for th eindicator, giving an average over the timing period. The timer type are VERY accurate if maintained like a fine mechanical watch. I first used them with large, low speed engines, where the speed varies during each rotation. They were a distinct upgrade from the pure rotation counter used with a pocket watch from the 19thcty into WW-II. Jaquet sold them under their name, as well as supplied them to others with different labeling, such as Herman Sticht in the US
9 месяцев назад
Also those types of tachometers wind up the clock mechanism by using it. Which is super smart, and means that pressing it without using it can wind it down.
Timer type tachos are still used on locomotives! I like them for their distinctive rhythmicity. They provide tachograms to waxed paper as well as speed-dependent circuit switching.
16:13 This translation might sound a bit weird in some places because the source does as well... ;) I tried to correct logical errors as good as I can. Electro Polygraph 662 The drive unit contains the synchronous motor with starting capacitor and a change-over gear for 5 different paper speeds. The connection terminal for the mains cable with ground wire is located on one of the PCBs on the side. On the other is a switch for switching the motor on and off, an electrical switch for forward and reverse gear and a button for operating the step gear. If the knob is turned slightly clockwise, it can be pushed in or out. The numbers engraved on the push bar indicate the selected gear. Level 1 2 3 4. 5 Paper speed 0.05 0.5 5 50 100 mm/sec The two rollers for the paper are located outside the gear box and can be removed from their bearings. The smooth flange can be removed in order to place the supply roll on the roller or to remove the rewound paper from the rewinding roller. The rollers must be inserted in such a way that the toothed flange engages with the protruding gear wheel of the gearbox. The drive unit is symmetrical. The paper runs from the supply roll over the inclined plane, is driven by the driving shaft arranged in the apex and runs again over an inclined plane to the take-up roll. The two inclined guide plates can be opened so that the various bearings can be conveniently oiled. The motor and the electrical circuit are located under the insulation cover (be careful with removed cover - 220 volts!). The drive roller is in two parts so that the drive pins can be adapted to the holes in the paper. The recording paper is inserted with the cover removed. However, the motor should only be switched on after the cover has been screwed on, as the two springs that are attached to the edge of the cover [Illustration] Electro Polygraph Type No. 662 of the drive shaft are attached to the cover. The cover is a box-shaped housing containing the recording magnets. It is fitted in such a way that its two lateral slots fit under the knurled screw knobs with which it is fixed to the drive unit. On the rear side are the connection terminals for wires or banana plugs, a common positive pole (red) and a separate negative pole for each magnet for an operating voltage of 12 or 24 volts DC. The writing levers with the writing tips protrude from the front. Each recorder can be lifted off the paper individually and there is also a swivelling bracket with which all recorders can be lifted off at the same time. This makes it possible to first use only one half of the recording magnets, then, with the recorders raised, switch off the paper feed and let the strip run backwards, after which the remaining recording magnets are used to record in the second pass. The high speed of 100 mm/sec can be switched on for the reverse run. However, it is not recommended to pass the paper through more than twice in forward motion, as otherwise the perforations may be damaged. There is no special time recorder, as the drive by means of a synchronous motor and stepped gearing makes time marking unnecessary. However, it is possible to feed one of the recording magnets with the periodic interrupter No. 654, page 10, and thus record time stamps. Maximum frequency 100 pulses/sec Dimensions: 26 cm long, 19 cm wide (with slide gate inserted) 20 cm high. The electro-polygraph comes in a pouch. The electro-polygraph is supplied in 2 types, which differ in the number of recording magnets. The motor voltage T10 or 220 volts, 50 periods is to be specified in each case. Magnet voltage 12 or 24 volts direct current. No. 662 Electro-polygraph with 12 magnets; Weight with pouch: approx. 11 kg. No. 663 Electro-polygraph with 6 magnets; Weight with pouch: approx. 10 kg. No. 664 Paraffinised paper, 12 cm wide, in rolls of approx. 50 m length.
9 месяцев назад+1
As an engineer this was awesome. The mechanical tachometers are works of art and last forever. The stroboscope with the sight is really useful, so that ambient lighting doesn't affect it.
The stroboscopic tachometer is a non contact one. You look through the device aiming a rotating object. You adjust the stroboscopic frequency till the object appears static and then you have a readout of the rotating frequency. You don't need a spot or sticker like for modern ones that give digital readings. You have to be careful, the readout can be double or half the actual speed.
Sooooooooo many things of beauty. An absolutely impressive haul. So Fran-tastic it outfrans Fran herself... and Dave Jones as well. All hail the Owlotron!
This is a real dream collection for tech engineers. Lots of old memories from when I had my first job (did lots of instrument calibration, technical documentation translations...).
You could hook up the mechanical tachs to a display where you can have users spin a wheel and see how fast they can get it up too. Even more fun if you add in some gearing they can change out.
Eichraum (picture shown at timestamp 29:07)in English is calibration room. This is where they calibrated all instruments. One of my former jobs in the '80's and '90's when I was working in the Netherlands (not for Jaquet). If you need German translations I may help.
I was just thinking about all these tacos in a museum display... I've got this collection of mostly DC motors... having them hooked up to some kind of microcontroller outputting perhaps varying PWM through power transistors would make a nice dial-flickering display.
At exactly 15:40, you moved something within the box. From what I can see through the bubble wrap, it looks like an electromechanically actuated stopwatch which I have. Jaquet model 309D. I made a video about it 10 years ago ( ruclips.net/video/C0q8KaeldKg/видео.html ), and used it to test the timing of my thermal time delay relays.
24:50 Adjustable High voltage (Kilovolts) generator. There is a guy on YT that use such thing to do experimental things (mostly very dangerous things).
The unboxing video to end all unboxing videos! All those displays and chart recorders and stuff will me with the urge to connect them all up to some kind of PC/microcontroller combination or Raspie Pi or something and have them all running like the scenery for THE most demented of 1970s Sci-Fi TV series you can imagine.
The analog writers are strip chart recorders. I can’t see it well on my IPhone, but it looks like they record 3 variables. They usually use 4-20 mA, 0-5 V, 1-5 V, or 0-10 V inputs.
Now the fun begins documenting everything. Should have "asset" tags on each piece so you can track them. Almost need rf tags on your item so you can find them
100% and a well crafted database with relevant info plus related files like scanned PDFs of any manuals, audio files etc. (my job is IT asset manager so… yeah… ha)
The very first item looked like it could have been a time domain reflectometer for measuring cables and feed lines and finding wiring faults. But, I'm only going on appearances.
Jaquet made speed and rotational sensors used in railway metro and tram. Also diesel and petrol engines, turbochargers, pumps and compressors. I think it is a very different jaquet that did anything medical
at 26 mins i think it looks like a pl control test bed for would be programmers . pl = phase logic control .. used in factories to programme and control industrial process equipment
That Syncardon must be something about blood and a limb The top left dial says something about cardiac signal And there's that text in the middle where it's written "Gonflage de la Manchette" That sounds like it's about inflating one of those things we use on the arms to take blood pressure
Yeah, Dont chuck the boxes out. I would always collapse decent boxes if heavy duty double-walled. For reassembly, use Scapa Brand tape. Nothing else comes up to it. Lucien gave me a lot of it years ago when he was at Ellstree Studios as it was used as the Original "Gaffer" Tape, where gaffer tape got its name from.
Wow what a sweet haul! I hope it's possible to make much of it interactive. Would be a shame if you are expected to just reproduce a private company's legacy display without your particular added flavor.
I think if there was a prequel to the movie Primer, this is how it would have started. LMNC doesn't know it yet but time travel is about to hit the museum.
The thingmajiggy around 24:40 could be something to measure the eardrums response to pressure changes as an indicator for obstructions in the middle ear. My daughters doctor just recently used such a device to check if her hearing impairment is of mechanical nature. The device looked like it was from the eighties and it was way more handheld-er than this beast. 😂
No idea what it is, but I can read german, so here is my guesswork from the labeling. First of: It has a setup and a treatment mode. "Manschettenfüllung": It uses some kind of pressure cuff/sleeve. Also has knobs for "pressure", "pressure begin", "pressure length" and "pulse wave". The dial indicator in the middle is in mmHg in the blood pressure range. So its a treatment device that uses some kind of pulsed pressure to affect the blood circulation. I'm thinking for example a full leg cuff that inflates and deflates to pressures you setup in the device to support/improve blood circulation. /edit shouldnt have stopped before the "head devices"...
@@agurdel You are very close. It is a Syncardon which is used for treatment of peripheral vascular disorders. "zur Behandlung von Durchblutungsstörungen"
Receiving this kind of collection sort of marks a transition towards being a more serious museum, with an emphasis on institutional memory, rather than just a collection of random stuff (not that there was anything wrong with that). It will be very interesting to see how the museum evolves. It wouldn't surprise me if there are many companies that find themselves in a similar position in the coming decades.
I think he crossed that line when he installed/ restored the telephone exchange facility.
agree!
You're gonna need a bigger museum!
I was just going to say the same thing!
Yep needs to call mi6
A TARDIS might be useful Sam .. 😉
@@garygazb I have raised the same issue before......the museum has dimensions not available to the rest of us....
The mechanical Tachs starting at around 9:50 are very, very useful. Jaquet made more then one type, including flyweight and timer types. They are general purpouse for use measuring ahsft speeds on motors, transmissions, machinery, etc. Usually with a set of contact tipe for getting into a 60degree machined center on a dhaft, and often with rollers for measuring surface speed (conveyor belt and the like) I still use them. The flyweight type direct read and can show speed variation, the timer type time for six seconds (usually) with a mechanical clock that engages and disengages a clutch for th eindicator, giving an average over the timing period. The timer type are VERY accurate if maintained like a fine mechanical watch. I first used them with large, low speed engines, where the speed varies during each rotation. They were a distinct upgrade from the pure rotation counter used with a pocket watch from the 19thcty into WW-II. Jaquet sold them under their name, as well as supplied them to others with different labeling, such as Herman Sticht in the US
Also those types of tachometers wind up the clock mechanism by using it. Which is super smart, and means that pressing it without using it can wind it down.
Timer type tachos are still used on locomotives! I like them for their distinctive rhythmicity. They provide tachograms to waxed paper as well as speed-dependent circuit switching.
16:13
This translation might sound a bit weird in some places because the source does as well... ;)
I tried to correct logical errors as good as I can.
Electro Polygraph 662
The drive unit contains the synchronous motor with starting capacitor and a change-over gear for 5 different paper speeds.
The connection terminal for the mains cable with ground wire is located on one of the PCBs on the side. On the other is a switch for switching the motor on and off, an electrical switch for forward and reverse gear and a button for operating the step gear.
If the knob is turned slightly clockwise, it can be pushed in or out. The numbers engraved on the push bar indicate the selected gear.
Level 1 2 3 4. 5
Paper speed 0.05 0.5 5 50 100 mm/sec
The two rollers for the paper are located outside the gear box and can be removed from their bearings. The smooth flange can be removed in order to place the supply roll on the roller or to remove the rewound paper from the rewinding roller.
The rollers must be inserted in such a way that the toothed flange engages with the protruding gear wheel of the gearbox.
The drive unit is symmetrical. The paper runs from the supply roll over the inclined plane, is driven by the driving shaft arranged in the apex and runs again over an inclined plane to the take-up roll. The two inclined guide plates can be opened so that the various bearings can be conveniently oiled. The motor and the electrical circuit are located under the insulation cover (be careful with removed cover - 220 volts!).
The drive roller is in two parts so that the drive pins can be adapted to the holes in the paper. The recording paper is inserted with the cover removed. However, the motor should only be switched on after the cover has been screwed on, as the two springs that are attached to the edge of the cover
[Illustration]
Electro Polygraph Type No. 662
of the drive shaft are attached to the cover. The cover is a box-shaped housing containing the recording magnets. It is fitted in such a way that its two lateral slots fit under the knurled screw knobs with which it is fixed to the drive unit. On the rear side are the connection terminals for wires or banana plugs, a common positive pole (red) and a separate negative pole for each magnet for an operating voltage of 12 or 24 volts DC. The writing levers with the writing tips protrude from the front. Each recorder can be lifted off the paper individually and there is also a swivelling bracket with which all recorders can be lifted off at the same time.
This makes it possible to first use only one half of the recording magnets, then, with the recorders raised, switch off the paper feed and let the strip run backwards, after which the remaining recording magnets are used to record in the second pass. The high speed of 100 mm/sec can be switched on for the reverse run.
However, it is not recommended to pass the paper through more than twice in forward motion, as otherwise the perforations may be damaged.
There is no special time recorder, as the drive by means of a synchronous motor and stepped gearing makes time marking unnecessary. However, it is possible to feed one of the recording magnets with the periodic interrupter No. 654, page 10, and thus record time stamps.
Maximum frequency
100 pulses/sec
Dimensions: 26 cm long, 19 cm wide (with slide gate inserted) 20 cm high.
The electro-polygraph comes in a pouch. The electro-polygraph is supplied in 2 types, which differ in the number of recording magnets.
The motor voltage T10 or 220 volts, 50 periods is to be specified in each case. Magnet voltage 12 or 24 volts direct current.
No. 662 Electro-polygraph with 12 magnets;
Weight with pouch: approx. 11 kg.
No. 663 Electro-polygraph with 6 magnets;
Weight with pouch: approx. 10 kg.
No. 664 Paraffinised paper, 12 cm wide, in rolls of approx. 50 m length.
As an engineer this was awesome.
The mechanical tachometers are works of art and last forever.
The stroboscope with the sight is really useful, so that ambient lighting doesn't affect it.
Excited to visit your museum one day!!! They couldn't have chosen a better group of folks to care for their history.
The stroboscopic tachometer is a non contact one. You look through the device aiming a rotating object. You adjust the stroboscopic frequency till the object appears static and then you have a readout of the rotating frequency. You don't need a spot or sticker like for modern ones that give digital readings. You have to be careful, the readout can be double or half the actual speed.
Sooooooooo many things of beauty. An absolutely impressive haul. So Fran-tastic it outfrans Fran herself... and Dave Jones as well.
All hail the Owlotron!
This is a real dream collection for tech engineers. Lots of old memories from when I had my first job (did lots of instrument calibration, technical documentation translations...).
the only thing I spotted was a bunch of complete nerds :)
You could hook up the mechanical tachs to a display where you can have users spin a wheel and see how fast they can get it up too. Even more fun if you add in some gearing they can change out.
I see a few turbo encabulators and hydrocoptic marzlevanes. Watch out for those spurving bearings!
What a goldmine of history cant wait to see what you do with it all.
11:00 is an optical tachometer, you put a reflective strip on the part rotating and line the optical head up with it.
What a fabulous haul! Plenty of material for future episodes.
Eichraum (picture shown at timestamp 29:07)in English is calibration room. This is where they calibrated all instruments.
One of my former jobs in the '80's and '90's when I was working in the Netherlands (not for Jaquet).
If you need German translations I may help.
The first item in the bubble wrap, that's an oscilloscope and a rather nice one at that if a bit old.
13:02 Schwingungsmesser unbekannt = Oscillation meter unknown
For measuring oscillations on overland high voltage line cables.
29:20: Eichraum = calibrating room
I build tachometers (for cars). Those tachos are probably for measuring the speed of motors for vacuum pumps and other lab and medical equipment.
vroom vroom NOPE more like Ehhh ehhh ehh
I saw at least one doodad, three thingamys and a couple of whatchamacallits. Hope this helps
you missed the duufers and later on in the line the thingamys had thingamabobs but I didn't see those.
I was just thinking about all these tacos in a museum display... I've got this collection of mostly DC motors... having them hooked up to some kind of microcontroller outputting perhaps varying PWM through power transistors would make a nice dial-flickering display.
You had me confused because I didn't see any Mexican food! Then I figured out you were talking about tachometers.
5:50 and 17:00 look like racks and scientific modules, similar to nim modules. I would say these are shorter.
At exactly 15:40, you moved something within the box. From what I can see through the bubble wrap, it looks like an electromechanically actuated stopwatch which I have. Jaquet model 309D. I made a video about it 10 years ago ( ruclips.net/video/C0q8KaeldKg/видео.html ), and used it to test the timing of my thermal time delay relays.
Ooohhh youve got a polygraph too how cool! Also you must be able to make music with that hearing test machine!
24:50 Adjustable High voltage (Kilovolts) generator. There is a guy on YT that use such thing to do experimental things (mostly very dangerous things).
Nice, i think I have the PC software and documents for this 4:57. It is quite a handy data recorder. Let me know if you need it.
The unboxing video to end all unboxing videos!
All those displays and chart recorders and stuff will me with the urge to connect them all up to some kind of PC/microcontroller combination or Raspie Pi or something and have them all running like the scenery for THE most demented of 1970s Sci-Fi TV series you can imagine.
13:25 Schwingungsmesser (unbekannt) - Vibration/Oscillation meter (unknown)
this is my absolut feel good content :) love it. Excited for the future videos what you gonna do with all of that
The analog writers are strip chart recorders. I can’t see it well on my IPhone, but it looks like they record 3 variables. They usually use 4-20 mA, 0-5 V, 1-5 V, or 0-10 V inputs.
Now the fun begins documenting everything.
Should have "asset" tags on each piece so you can track them.
Almost need rf tags on your item so you can find them
100% and a well crafted database with relevant info plus related files like scanned PDFs of any manuals, audio files etc. (my job is IT asset manager so… yeah… ha)
Loving this shit, gents
The thing that has height on it might be a pressure gauge with height being head, like mm mercury, if it's metres maybe it's water?? 13:14
Cool haul, but a tricky thing to archive all this, ever applied for national lottery funding /grants.
Measuring speed of turbines and turbos with mechanical instruments is kind of impressive.
So cool! You can see all sorts of crazy stuff with the strobe o scope.
Marvelous!
13:25 Schwingung is Vibration or frequency - maybe for testing motor stands?😊
Some of the tachometers are dial turn indicators judging by what was written on the box
The very first item looked like it could have been a time domain reflectometer for measuring cables and feed lines and finding wiring faults.
But, I'm only going on appearances.
Jaquet made speed and rotational sensors used in railway metro and tram. Also diesel and petrol engines, turbochargers, pumps and compressors. I think it is a very different jaquet that did anything medical
So cool! Feels like creepy medical Christmas.
First one looked like it could be an old oscilloscope, guessing 60s or 70s based on the size of that crt.
i tried to come up with a clever comment but the best thing i could come up with is "i love you" so there you go
18:00 U/min - Umdrehung per Minute (Revolution/min)
at 26 mins i think it looks like a pl control test bed for would be programmers . pl = phase logic control .. used in factories to programme and control industrial process equipment
1:55 is that a vintage osciloscope?
So when you opening the second building🤣
22:28 The name of the doctor on the machine is fun :D
i'd like to see the ear-tester and head-squeezer used together. a worthy request maybe..
That's some nice "tach-nology" you have there!
That Syncardon must be something about blood and a limb
The top left dial says something about cardiac signal
And there's that text in the middle where it's written "Gonflage de la Manchette"
That sounds like it's about inflating one of those things we use on the arms to take blood pressure
That's correct - I think they were used for improving circulation in limbs by rhythmic pumping (ooer) of a pressure cuff.
Yeah, Dont chuck the boxes out. I would always collapse decent boxes if heavy duty double-walled. For reassembly, use Scapa Brand tape. Nothing else comes up to it. Lucien gave me a lot of it years ago when he was at Ellstree Studios as it was used as the Original "Gaffer" Tape, where gaffer tape got its name from.
Wow what a sweet haul! I hope it's possible to make much of it interactive. Would be a shame if you are expected to just reproduce a private company's legacy display without your particular added flavor.
2:00 oscilloscope?
I think if there was a prequel to the movie Primer, this is how it would have started. LMNC doesn't know it yet but time travel is about to hit the museum.
imagine 88 musical MRI machines controlled by midi and synth. maybe 88 hadron colliders that make sounds
That would make at least 88 hardons here.😊
A music video like no other will happen from this one day heh
It's clear what you have is parts of the prototype for the HyperEncabulator!
Mega haul!
It was better that you waited till the end to open the docs box. I do so love opening a pallet of boxes and not knowing what to expect.
3:47 Looks like Fuji 3015 Minitrons - Incandescent 7-segments
100%, built into a tachometer. They look gorgeous! 😍
Amazing! 🙂
6:54 Thats Keith
(17:53) looks like it might be a teletype phone or current loop interface. contact curious Marc to be sure.
Very sure it is a Telex dialler, used with a TTY
TOP SECRETS are fun
The thingmajiggy around 24:40 could be something to measure the eardrums response to pressure changes as an indicator for obstructions in the middle ear. My daughters doctor just recently used such a device to check if her hearing impairment is of mechanical nature. The device looked like it was from the eighties and it was way more handheld-er than this beast. 😂
No idea what it is, but I can read german, so here is my guesswork from the labeling. First of: It has a setup and a treatment mode. "Manschettenfüllung": It uses some kind of pressure cuff/sleeve. Also has knobs for "pressure", "pressure begin", "pressure length" and "pulse wave". The dial indicator in the middle is in mmHg in the blood pressure range. So its a treatment device that uses some kind of pulsed pressure to affect the blood circulation. I'm thinking for example a full leg cuff that inflates and deflates to pressures you setup in the device to support/improve blood circulation.
/edit shouldnt have stopped before the "head devices"...
@@agurdel You are very close. It is a Syncardon which is used for treatment of peripheral vascular disorders. "zur Behandlung von Durchblutungsstörungen"
great to see the googol counter.
Nowadays Jaquet is part of TE and they make precision sensors.
26:30 control center for fireworks/demolition
Typo in the name? Ujnpacking
U / min = Umdrehungen pro Minute = rotations per minute
if you connect them all you will be able to travel thru time... ; )
A N O T H E R T A C H O M E T E R
24:01 you have to shave his head to make it work :)
Xmas