FINALLY! A short and very informative video! Getting ready to hang trim and was going to use that to justify a nail gun. But I had NO CLUE as to what I needed. Thanks. I have a combination stapler/brad nailer, but I knew those brads would be too short for my application. Now I know what to buy.
Thank you a million for the video. Seriously, trying to sift through 40 minute wood working videos to get basic fuckin info is a pain in the neck. Definitely earned a sub
Good vid. Short and to the point. I was considering getting a framing nailer (which I used a lot when I was building houses), a brad nailer, and a pin nailer now that I'm gearing up to retire and will be trying different projects in my shop. This saved me some money. I'll get the framing and brad nailers, but it's clear for my needs that I can forgo the wire nailer.
Framing nailers are a whole other video we should shoot! Most people if they could only choose 1 of these 3 will go with brad nailer because it can do a little of everything. Of course normally the job/project right in front of you will dictate the tool you buy next off the wishlist.
When I lived in the big city there was always a lot of construction going on all around. And after awhile I was able to tell the top crews from the not. The top crews you could hear their nail guns but the not was still swinging hammers like it was last century or something. Im guessing the not crews were paid less and the entire project moved slower. ALSO, the top crews seem to be on commercial buildings while the not was doing residential work. I had heard the way it worked was, the carpenters were to provide their own guns while the contractors would provide air-hoses & nails. Now, I see they have cordless nail guns. So cool! just an observation.. !
Thanks for explaining the different types of nail-guns !!! But I am really worried about how to remove those nails-without-a-head, when I want to take something apart again...🤔
Great video! Could you use a Pin Nailer for accent wall designs when using 1/2" or 3/4" thick pine or MDF and CA glue is used where the all the peaces joint together?
You certainly could! Pin nailers are perfect for accent wall designs, especially very small or delicate ones! Anything bulkier though and you'd best be looking at a brad nailer to get the job done!
Great video. I wasn't really able to gauge which nailer I would need. But if I want to make a cabinet on wheels for a 50 pound air compressor should I use the Finish nailer with 15gauge nails?
Brad nails would probably be your best bet if you're working with metal sheets; pin nails would definitely be too small, and while you'd have more than enough power with a finish nailer, the brad should get the job done and be able to save you some cash!
Hello. I’m doing board and batten as my first DIY home project. I got the 1” (3/4#) inch thick pine wood trim. I only have a brad nailer. What size of nail do you recommend me use? And should I use a wood glue to well secure the trim to the wall? Or would you recommend using a finish nailer?
I would suggest a 1 to 2 inch, in length, 18-gauge brad nails. Also wood glue is a great addition for stability while you're installing. While a finish nailer may offer more holding power, the brad nailer you have will do just fine!
What a great video! I refinish furniture which has not always been "gently used", so I need to know how to restore some things. Your video really helped me out. Thanks!
As a weekend DIY'er that will occasionally build furniture or do accent walls, etc - would the brad nailer be my best bet? since it is the most versatile? I did want to do crown molding eventually though and it sounds like the brad nailer may not work for my needs.
I think I already know the answer to this based on seeing the three different guns in your video. But can you use the same nail gun for all the different nail styles? I have a brad nail gun from Ryobi I have enjoyed using. But I think I need finishing nails for a new project. Do I need to get a whole new nail gun?
No, you should not use finishing nails in a brad nailer because the two types of nails require different tools to drive them safely and neatly. If it's just for one project, you may be able to rent one somewhere near you, but if you will need to do so often we'd recommend both nailers.
Great video! Was trying to decide which to get for my first cordless nailer, Brad or Finish. Can't afford mouth at that moment, so wanted the most versatile. This helped.
Looking for something battery powered for fence pickets. Looking like 15 gauge might be a good option but should they be galvanized? I'm tempted to try a brad nailer and just shoot 2-3 extra nails per picket, but not sure how 18 gauge would do vs wind and rain.
Corded nailers are not very popular, they jumped right from air hoses to battery powered and never looked back. Metabo HPT does make an adapter to use their battery tools with a plug but assume you’re looking to keep cost down vs adding an expensive accessory onto a battery tool.
Hey Gareth! That sounds about right to us! You may want to get a pin nailer if you're going to be putting some fancier accoutrements on it, but for your basic wardrobe a brad nailer should do the trick!
OK I'm refinishing a couple of rooms in my house. I'm just gonna be doing the trim work so should I use a finished nailer or a Brad nailer? I'm a little confused still I know the finished nail. I would probably be the better of the 2 tools but I also tend to overpurchase. So would the brad naylor be sufficient as what i'm asking
Yes! A brad nailer should be able to do the trick for you; a finish nailer would do the job just as well, but if you want to save a little bit of money, go with the brad!
It depends on the thickest of your wood, so a Brad Nailer would be best for delicate and thin materials and a Finish Nailer would be best for slightly thicker material.
What do you think: Is the finish nailer the best choice for installing timber weatherboards? I have a large Ecko framing gun (the Ultimate 90 gas framer), but that seems way too powerful.
Technically, you could use a Finish Nailer, but probably not the best choice. Those weatherboards could have some thickness to the material so your framing gun is better suited in my opinion. Could shop for a battery powered Framing Nailer if you're wanting something a little lighter.
Yes they do! Here is the link to our website: www.ohiopowertool.com/milwaukee-tool-2841-20 There is also a kit available as well www.ohiopowertool.com/milwaukee-tool-2841-21ct
Wonderful video. That was very informative and you made the content easy to understand. I'm new to powered nailers and while I know there are various products on the market, I don't have a solid working knowledge of the options, depending on the job at hand. Thank you for explaining the when's, why's and likely outcomes when deciding which tool to use.
Hey Franklin! Glad we were able to help! Please feel free to reach out if there are any questions we can help to answer and best of luck with your powered nailer journey!
Good informative video. Curious about fastening thin and soft cedar shingles, into oak framing. The brad nailer shoves the brads thru the thin cedar, and doesn't secure. Would a finish nail have a bigger head, and secure better? Anyone? Thanx.
Using a finish nailer is a better option because of the reasons you stated, however because you are still working with delicate wood, you'll still have to be careful not to split the wood. You can also pre-drill pilot holes with a drill bit slightly smaller in diameter than the finish nails, this can sometimes help!
Brad nails may not offer the best holding power, we recommend a larger nail or fastener! These include finish nails or even screws - both can provide more holding power than brad nails.
A pin nailer can generally be used to secure a 1x2 furring strip without causing significant cracking or splitting, as long as you are careful to drive the nails at a slight angle, use the right nail length for the material you're attaching it to, and avoid nailing too close to the edge of the furring strip. However, for added security, especially if attaching to a hard surface, consider using screws or a combination of nails and screws.
Hi, for fencing jobs we suggest you use a finish nailer. It can provide more strength and holding power to drive larger nails to secure fence boards and panels.
Always important to remember! Well, that and not crossing the streams, but sometimes you have to be a little flexible if you want to defeat Zuul and save New York! (The pointy end should still go away from you, Gozer commands it!)
@@OhioPowerTool” ….dogs and cats, living together! Mass hysteria!!!” Almost as important as not putting your yellow tools into red boxes. Just don’t do it, man. It’s just too big a risk.
Gauge is thickness (lower # thicker) so 15g is a little fatter that 16g. Application wise the nails themselves are used interchangeably. The tool setup, length and nail strips many people have personal preferences we wouldn’t argue with.
Those square staples sound like T-50 staples. All the larger staples from a staple gun are heavier. If you want to use staples instead of nails for stronger work, look at a bostich crown stapler; my grandfather has one that’s even bigger for cabinets.
@@liquidrockaquatics3900 I ended up getting a Grex 2116AD and 3/16 x 3/8, 22-gauge staples. I guess it's technically an upholstery stapler, although I'll never use it for that. Very nice stapler, quiet, gentile.
They use different types of nails, 30 degrees are typically a little cheaper so more popular in certain areas but 20-22 degrees can use different types of nails commonly needed in hurricane zones so become more common in coastal areas. But you get both in most areas these days so comes down to user preference at this point.
In general, a thicker nail (lower gauge) will provide more holding power than a thinner one. The increased thickness of a 15-gauge finishing nail means it can typically withstand greater stress and pullout forces compared to a 16-gauge nail
Not really I use my Brad nailer to do everything from trim to building cabinets. My opinion it’s the best of both worlds. If you won’t be using it much ryobi makes an 18g that’s a nice sweet spot for only $89.
Hey David! Your best bet for baseboards would likely be a finish nailer, just due to the holding power on the nails themselves. You may be able to get away with a brad nailer, but definitely not a pin nailer. Hope that helps!!
Oh sure! Now, keep in mind that the brad nails won't have as much holding power as finish nails, so you may find yourself using more of them to fully anchor the baseboards to the wall. Start small and make sure you angle at least the first set of nails to give yourself a little room for extra just to be safe, and good luck!
Generally, they are! They're all used for fastening, or adjoining, pieces of wood together. If, however, you try using a pin nailer for, say, a baseboard project, you'll find the holding power in a pin nailer significantly lacking. Conversely, if you try using a finish nailer for some decorative trim, the nail will at least damage, if not completely obliterate, the piece you're working on. It's sort of like choosing the correct sized screwdriver; too large, and you can strip the screw if the head will even fit, too small and you won't get any leeway!
Correct! We're focusing on battery-powered nailers in this video; for the most part, the information translates across the board! The pneumatics give the nailer a boost in speed, allowing you to get through a project quicker than you would with a cordless one; however, you're then at the mercy of cords and hoses and the like, whereas a cordless nailer gives you the freedom of movement throughout the jobsite without having to lug a whole setup around!
#newsubhere Clearly told and power tools are a heck of alot way different since I was young and even in carpentry school. Innovation definitely changed tremendously! #Thankyoufortheinformation #keepupthegreatwork
What an excellent question! The answer to this depends somewhat on what wood you're planning on using, as well as if they're purely for decoration or if you plan on making them functional. For the most part, you should be able to get away with a fairly strong wood glue or even some longer hand screws if the wood is pliable enough, though if you're set on using a nailer, brad nails would be the way to go! Remember that the orientation of the nailer is important so the nails don't go shooting into or out of the birdhouse at awkward angles, and if these are going to be functional for birds, be sure to add some ventilation and drainage features to make it comfortable for them and have fun!
@@OhioPowerTool hey thanks. See I’m a quadriplegic so using a drill and screws is to difficult. I do have good arm function and limited hand function and believe I can manipulate the nailer well enough to use. I’m planning to build some log cabin style birdhouses using locally sourced limbs and such. Might make a few other designs as well though. I should be able to set the nail depth on the nailer though right. If not I should be able to adjust my air pressure to reduce penetration I think. I appreciate you getting back with me though.
That sounds like a phenomenal project! You should definitely be able to get away with using a brad nailer for that, and we'd also recommend having some spare wood putty or glue on hand to seal over any nail holes that you don't want exposed. Best of luck to you, and if there's anywhere that you can post the finished product, we'd love to see them!!
The only thing about not having a place that you can take classes about power tools is meeting cool people on you tube that help more often then not. The only draw back is that I only find videos that 2 yrs old or more, and by that time, no one answers your questions anymore 😮💨.
@@OhioPowerTool Absolutely love mine. They’ve also been killing it on their Gen 2 Nailers; 18 ga Brad, 16ga, and 15ga Finish. Solid and reliable. In all honesty, though, bang for the buck, the Craftsman ones are also not bad. Bulky as all get out, but not bad. They have a great belt hook and hang well on a belt or tool belt if you need to climb a ladder.
Heres my 10 cents as a fixer in Australia for whoever reading the comment section please let me know if im wrong Architraves = 18g 40mm Skirtings = 16 gauge 50mm & 38mm on certain areas like cavaty sliders and water pipes. Internal/ External door jambs = 15g 50mm & 64mm All my power tools are cordless hikoki and I'm happy 😊 Dont forget to smash that button 👇
FINALLY! A short and very informative video! Getting ready to hang trim and was going to use that to justify a nail gun. But I had NO CLUE as to what I needed. Thanks. I have a combination stapler/brad nailer, but I knew those brads would be too short for my application. Now I know what to buy.
Thank you a million for the video. Seriously, trying to sift through 40 minute wood working videos to get basic fuckin info is a pain in the neck. Definitely earned a sub
“the pointy end goes away from you”. As soon as I heard that I knew I was watching the right video! Lol
Thanks!
Good vid. Short and to the point. I was considering getting a framing nailer (which I used a lot when I was building houses), a brad nailer, and a pin nailer now that I'm gearing up to retire and will be trying different projects in my shop. This saved me some money. I'll get the framing and brad nailers, but it's clear for my needs that I can forgo the wire nailer.
Framing nailers are a whole other video we should shoot! Most people if they could only choose 1 of these 3 will go with brad nailer because it can do a little of everything. Of course normally the job/project right in front of you will dictate the tool you buy next off the wishlist.
When I lived in the big city there was always a lot of construction going on all around. And after awhile I was able to tell the top crews from the not.
The top crews you could hear their nail guns but the not was still swinging hammers like it was last century or something. Im guessing the not crews
were paid less and the entire project moved slower. ALSO, the top crews seem to be on commercial buildings while the not was doing residential
work. I had heard the way it worked was, the carpenters were to provide their own guns while the contractors would provide air-hoses & nails. Now,
I see they have cordless nail guns. So cool!
just an observation..
!
Which cordless nailer is the best for running around in parking lots & shooting nails into tires?
I like your question, cos im also looking for that one in particular
huh???
@@CRAZEH247you heard ehat he said
Everyone should have a hobby...
Won't work you can barely get them to stick in cardboard at 3 feet
Thanks. I’m finishing a home project.
This is exactly the video I needed.
Thanks Walt! Glad we were able to help!!
Finish Nailer -> Max gauge. Name makes no sense whatsoever 🤯
"Finish(ed)", aka: done, not coming out, not coming back, finished.
Well they are the largest for finish style and fine carpentry. But roofing and framing nailers are still way bigger
Thanks for explaining the different types of nail-guns !!!
But I am really worried about how to remove those nails-without-a-head, when I want to take something apart again...🤔
I got a 15 to 50mm brad 18G OZITO nailer. Adjustable depth. 18v battery powered. Single Shot or Rapid Fire. Fast Fencing. Awesome Tool.
Super good video. Thanks! I am doing re-flooring. I guess I should choose Brad nailer for putting back skirting(Moulding), correct? Thanks.
Great video! Could you use a Pin Nailer for accent wall designs when using 1/2" or 3/4" thick pine or MDF and CA glue is used where the all the peaces joint together?
You certainly could! Pin nailers are perfect for accent wall designs, especially very small or delicate ones! Anything bulkier though and you'd best be looking at a brad nailer to get the job done!
Great video. I wasn't really able to gauge which nailer I would need. But if I want to make a cabinet on wheels for a 50 pound air compressor should I use the Finish nailer with 15gauge nails?
Does it work on metal sheets?
Brad nails would probably be your best bet if you're working with metal sheets; pin nails would definitely be too small, and while you'd have more than enough power with a finish nailer, the brad should get the job done and be able to save you some cash!
Thanks, simple and straight to the point.!!!
What would be the best all around for a travel trailer? Some panels and trim are starting to separate
Hello. I’m doing board and batten as my first DIY home project. I got the 1” (3/4#) inch thick pine wood trim. I only have a brad nailer. What size of nail do you recommend me use? And should I use a wood glue to well secure the trim to the wall? Or would you recommend using a finish nailer?
I would suggest a 1 to 2 inch, in length, 18-gauge brad nails. Also wood glue is a great addition for stability while you're installing. While a finish nailer may offer more holding power, the brad nailer you have will do just fine!
Hello. What 110 volt nail gun do I use to shoot 1 3/4 inch finishing nails into 1 by 2 lumber?
What a great video! I refinish furniture which has not always been "gently used", so I need to know how to restore some things. Your video really helped me out. Thanks!
Glad we could help Catherine!!
As a weekend DIY'er that will occasionally build furniture or do accent walls, etc - would the brad nailer be my best bet? since it is the most versatile? I did want to do crown molding eventually though and it sounds like the brad nailer may not work for my needs.
I think I already know the answer to this based on seeing the three different guns in your video. But can you use the same nail gun for all the different nail styles? I have a brad nail gun from Ryobi I have enjoyed using. But I think I need finishing nails for a new project. Do I need to get a whole new nail gun?
No, you should not use finishing nails in a brad nailer because the two types of nails require different tools to drive them safely and neatly. If it's just for one project, you may be able to rent one somewhere near you, but if you will need to do so often we'd recommend both nailers.
Just what I needed!
Glad we were able to help, Carole!!
Great video! Was trying to decide which to get for my first cordless nailer, Brad or Finish. Can't afford mouth at that moment, so wanted the most versatile. This helped.
Glad we could be of assistance! Feel free to let us know if you have any further questions that we can help with!!
Thank you for this short and informative video! 🙌
I heard the Ridgid nail guns are very reliable for morning wood.
Brushless motor
We’ve heard good things about Ridgid as well. Not a brand we sell (not the Ridgid Orange at least) but part of TTI family with Mikwaukee Tool.
Looking for something battery powered for fence pickets. Looking like 15 gauge might be a good option but should they be galvanized? I'm tempted to try a brad nailer and just shoot 2-3 extra nails per picket, but not sure how 18 gauge would do vs wind and rain.
You want galvanized finish for use in exterior
Thank you for the explanation of the differences. Where can I find a 16 gauge finish nailer that is electric. You know that runs on household current?
Corded nailers are not very popular, they jumped right from air hoses to battery powered and never looked back. Metabo HPT does make an adapter to use their battery tools with a plug but assume you’re looking to keep cost down vs adding an expensive accessory onto a battery tool.
I’m planning on doing a slat wall in my bedroom with a 2” thick slat, which would be better a Brad nailer or a finishing nailer?
Great video, very helpful.
Thanks! Just what I needed
Which nailer do I need for framing up, 2x4’s … preferably battery powered… thanks
Quality content. Thanks for uploading.
Excellent video cheers. So if you're putting together a wardrobe made of 18mm mdf you would use the Brad nailer? Thank you.
Hey Gareth! That sounds about right to us! You may want to get a pin nailer if you're going to be putting some fancier accoutrements on it, but for your basic wardrobe a brad nailer should do the trick!
@@OhioPowerTool excellent thanks a lot for the information!!
Best of luck!!
Hi !! Can brad nail gun be used on concrete walls to fix mdf mouldings ?
A concrete nailer would most likely be the better option for that application.
@@OhioPowerTool thank you !!
OK I'm refinishing a couple of rooms in my house. I'm just gonna be doing the trim work so should I use a finished nailer or a Brad nailer? I'm a little confused still I know the finished nail. I would probably be the better of the 2 tools but I also tend to overpurchase. So would the brad naylor be sufficient as what i'm asking
Yes! A brad nailer should be able to do the trick for you; a finish nailer would do the job just as well, but if you want to save a little bit of money, go with the brad!
What's the best nailer to use when doing base boards around the house?
It depends on the thickest of your wood, so a Brad Nailer would be best for delicate and thin materials and a Finish Nailer would be best for slightly thicker material.
What do you think: Is the finish nailer the best choice for installing timber weatherboards?
I have a large Ecko framing gun (the Ultimate 90 gas framer), but that seems way too powerful.
Technically, you could use a Finish Nailer, but probably not the best choice. Those weatherboards could have some thickness to the material so your framing gun is better suited in my opinion. Could shop for a battery powered Framing Nailer if you're wanting something a little lighter.
Thanks, great explanation!
Does the Milwaukee have angular nailing capabilities for things like corner molding?
Yes they do! Here is the link to our website: www.ohiopowertool.com/milwaukee-tool-2841-20
There is also a kit available as well www.ohiopowertool.com/milwaukee-tool-2841-21ct
is there a nailer that multi purpose, that is, one nailer can be used for large and small projects?
Brad Nailers are typically a good general-use nailer for large and small projects.
Wonderful video. That was very informative and you made the content easy to understand. I'm new to powered nailers and while I know there are various products on the market, I don't have a solid working knowledge of the options, depending on the job at hand. Thank you for explaining the when's, why's and likely outcomes when deciding which tool to use.
Hey Franklin! Glad we were able to help! Please feel free to reach out if there are any questions we can help to answer and best of luck with your powered nailer journey!
Good informative video. Curious about fastening thin and soft cedar shingles, into oak framing. The brad nailer shoves the brads thru the thin cedar, and doesn't secure. Would a finish nail have a bigger head, and secure better? Anyone? Thanx.
Using a finish nailer is a better option because of the reasons you stated, however because you are still working with delicate wood, you'll still have to be careful not to split the wood. You can also pre-drill pilot holes with a drill bit slightly smaller in diameter than the finish nails, this can sometimes help!
@@OhioPowerTool thanks for the reply. :)
Super helpful - thanks!
Hi, can you use a pin nailer on mdf? Thanks
A finish nailer might be your better option for MDF.
How can I nail aluminum soffit fasia without having the nail head sink in?
what would work best for building a sturdy privacy fence? both for the 2x4s as well as the slats?
Probably a fencing nail gun.
@@sypher0101 😂
One not covered here - a framing nailer.
Screws
I'm covering a wall with 3/4 inch thick pine. I'll need to drive thru drywall to get to the frame. Does brad nails have enough strength?
1x6x10 - pine
Brad nails may not offer the best holding power, we recommend a larger nail or fastener! These include finish nails or even screws - both can provide more holding power than brad nails.
I'm trying to secure a 1x2 furring strip to something. Will a Pin Nailer be ok to use or will it still crack/split it?
A pin nailer can generally be used to secure a 1x2 furring strip without causing significant cracking or splitting, as long as you are careful to drive the nails at a slight angle, use the right nail length for the material you're attaching it to, and avoid nailing too close to the edge of the furring strip. However, for added security, especially if attaching to a hard surface, consider using screws or a combination of nails and screws.
Thank You.
Awesome video, thank you!
How much your diamond core bit?
Great video!
Which one to use for fencing?
Hi, for fencing jobs we suggest you use a finish nailer. It can provide more strength and holding power to drive larger nails to secure fence boards and panels.
😮 Pointy end goes AWAY from you!
“Important safety tip! Thanks Egon.”
Always important to remember! Well, that and not crossing the streams, but sometimes you have to be a little flexible if you want to defeat Zuul and save New York!
(The pointy end should still go away from you, Gozer commands it!)
@@OhioPowerTool” ….dogs and cats, living together! Mass hysteria!!!”
Almost as important as not putting your yellow tools into red boxes. Just don’t do it, man. It’s just too big a risk.
@@jamesmocharski4803 I put red tools in black and yellow boxes so I can find them. Same with fasteners. You need to see what’s in there.
What's the difference between 15d and 16d finish nailer?
Gauge is thickness (lower # thicker) so 15g is a little fatter that 16g. Application wise the nails themselves are used interchangeably. The tool setup, length and nail strips many people have personal preferences we wouldn’t argue with.
Which is best for securing 1/4 round to baseboard?
ruclips.net/user/shorts0yZNL9RBHMc
I have small staples: 3/6" wide X 5/8" deep, I believe them to be about 21 gauge, square head - what will shoot these staples?
Those square staples sound like T-50 staples. All the larger staples from a staple gun are heavier. If you want to use staples instead of nails for stronger work, look at a bostich crown stapler; my grandfather has one that’s even bigger for cabinets.
@@liquidrockaquatics3900 I ended up getting a Grex 2116AD and 3/16 x 3/8, 22-gauge staples. I guess it's technically an upholstery stapler, although I'll never use it for that. Very nice stapler, quiet, gentile.
I have all 3 - 15ga, 18ga, and 23ga.
Hi need some help
What's the best for making cabinets carcasses (capentry
You'd probably be best off with a brad nailer! They're quite versatile and would be best for all around cabinetry!
Crushed it. Thanks!
Glad you enjoyed, thanks for taking the time to check us out!
This video answered every question I had when I looked for a video like this
What the difference between 20 degree and 30degree for framing
They use different types of nails, 30 degrees are typically a little cheaper so more popular in certain areas but 20-22 degrees can use different types of nails commonly needed in hurricane zones so become more common in coastal areas. But you get both in most areas these days so comes down to user preference at this point.
@@OhioPowerTool whats the difference though, do they go in at an angle or it is just the angle they are arranged in the clip?
Is there really that much of a difference in holding power between a 16g and 15g finishing nails?
In general, a thicker nail (lower gauge) will provide more holding power than a thinner one. The increased thickness of a 15-gauge finishing nail means it can typically withstand greater stress and pullout forces compared to a 16-gauge nail
Not really I use my Brad nailer to do everything from trim to building cabinets. My opinion it’s the best of both worlds. If you won’t be using it much ryobi makes an 18g that’s a nice sweet spot for only $89.
Do you recommend it to put baseboards?
Hey David! Your best bet for baseboards would likely be a finish nailer, just due to the holding power on the nails themselves. You may be able to get away with a brad nailer, but definitely not a pin nailer. Hope that helps!!
Oh thank you so much
Do you think that can I use the Dewalt DCN680 18GA?
Oh sure! Now, keep in mind that the brad nails won't have as much holding power as finish nails, so you may find yourself using more of them to fully anchor the baseboards to the wall. Start small and make sure you angle at least the first set of nails to give yourself a little room for extra just to be safe, and good luck!
Oh thank you so much I appreciate your response you do an excellent job
Thanks for nailing us.😅
Great Update
Thanks Jamal! Glad you dug it!!
Awesome info
The xgt pinner is the best,I'll be waiting on the brad..😇
Hopefully we'll be getting one soon! They've already got them overseas, so fingers crossed for an announcement soon!
@@OhioPowerTool great! I didn't know they had one overseas, thanks for the info!
I'm still confused. They all seem to be used for the same applications.
Generally, they are! They're all used for fastening, or adjoining, pieces of wood together. If, however, you try using a pin nailer for, say, a baseboard project, you'll find the holding power in a pin nailer significantly lacking. Conversely, if you try using a finish nailer for some decorative trim, the nail will at least damage, if not completely obliterate, the piece you're working on. It's sort of like choosing the correct sized screwdriver; too large, and you can strip the screw if the head will even fit, too small and you won't get any leeway!
There is something about some nailers being pneumatic i.e use air pressure as power source. You did not go into that detail.
Correct! We're focusing on battery-powered nailers in this video; for the most part, the information translates across the board! The pneumatics give the nailer a boost in speed, allowing you to get through a project quicker than you would with a cordless one; however, you're then at the mercy of cords and hoses and the like, whereas a cordless nailer gives you the freedom of movement throughout the jobsite without having to lug a whole setup around!
Thanks For the help buddy
#newsubhere Clearly told and power tools are a heck of alot way different since I was young and even in carpentry school. Innovation definitely changed tremendously! #Thankyoufortheinformation #keepupthegreatwork
Happy you found us! It is certainly a fast-paced and ever-changing industry. It's always exciting to see what people are coming out with next!
@OhioPowerTool I agree! Keep up the great work. Is love to see more. #thanksforsharing
I’m looking to get something simply to build some bird houses. Should I go brad or pin?
What an excellent question! The answer to this depends somewhat on what wood you're planning on using, as well as if they're purely for decoration or if you plan on making them functional. For the most part, you should be able to get away with a fairly strong wood glue or even some longer hand screws if the wood is pliable enough, though if you're set on using a nailer, brad nails would be the way to go! Remember that the orientation of the nailer is important so the nails don't go shooting into or out of the birdhouse at awkward angles, and if these are going to be functional for birds, be sure to add some ventilation and drainage features to make it comfortable for them and have fun!
@@OhioPowerTool hey thanks. See I’m a quadriplegic so using a drill and screws is to difficult. I do have good arm function and limited hand function and believe I can manipulate the nailer well enough to use. I’m planning to build some log cabin style birdhouses using locally sourced limbs and such. Might make a few other designs as well though. I should be able to set the nail depth on the nailer though right. If not I should be able to adjust my air pressure to reduce penetration I think. I appreciate you getting back with me though.
That sounds like a phenomenal project! You should definitely be able to get away with using a brad nailer for that, and we'd also recommend having some spare wood putty or glue on hand to seal over any nail holes that you don't want exposed. Best of luck to you, and if there's anywhere that you can post the finished product, we'd love to see them!!
@@OhioPowerTool do you guys have a Facebook page?
@@LeaveItToTheWolves We do! We're @ohiopowertool on Facebook, Twitter, Instagram, and TikTok!
Thank you thank you thank you
so you’re saying to buy all three
If you need all 3!
The only thing about not having a place that you can take classes about power tools is meeting cool people on you tube that help more often then not. The only draw back is that I only find videos that 2 yrs old or more, and by that time, no one answers your questions anymore 😮💨.
We try to stay on top of the questions, if we're not hitting them for anyone here, can always give us a call 614-481-2111. Thanks for watching!
Someone just tell me which one to get please 😂
I'm gonna take the Milwaukee cause the angle, but blame the blue looks all accessible
That Milwaukee's got a very comfortable angle to it, it's a fantastic tool!
@@OhioPowerTool Absolutely love mine.
They’ve also been killing it on their Gen 2 Nailers; 18 ga Brad, 16ga, and 15ga Finish.
Solid and reliable.
In all honesty, though, bang for the buck, the Craftsman ones are also not bad.
Bulky as all get out, but not bad. They have a great belt hook and hang well on a belt or tool belt if you need to climb a ladder.
Heres my 10 cents as a fixer in Australia for whoever reading the comment section please let me know if im wrong
Architraves = 18g 40mm
Skirtings = 16 gauge 50mm & 38mm on certain areas like cavaty sliders and water pipes.
Internal/ External door jambs = 15g 50mm & 64mm
All my power tools are cordless hikoki and I'm happy 😊
Dont forget to smash that button
👇
I wish you spent more time, going deep on the explanation, to be honest!!!
Hey KJ! Thanks for the feedback! What could we provide more details on?
too short video, please
🔄
Outdamnstanding video
Small trim 23g med size 18g large trim 16g or 15g
Awesome video!! Thanks