This setup poses an extreme risk of electric shock and potential fire hazard as all terminal are easily accessible and - if you're REALLY unlucky - lethal if your house doesn't happen to have a RCD circuit breaker. Don't try this at home, kids!
actually kids, your suppose to lick the red terminals to strip em..kids might b stupid but the ones watcin this video know better than to lick the hot side of the panel. so i think were good. btw rcd's or gfci (ground fault circuit interrupter) with variations on that can still kill in jus the wrong scenarios like with somebody with heart problems
@@thawzinkhant1759 yeah, thanks...i understand now! What can i do to increase the pause between 2 flashes, if i connect another capacitor in parallel or a bigger capacitor it works ?
no dear speed will remain constant if you want ot increase speed use low power capacitor plz visit my web for more deaill circuits tinyurl.com/y6fm4d5g
Awesome, this is what I am looking for.
Hello! I built this project but the pause between 2 flashes is too short, have you any idea what can I do ?
This setup poses an extreme risk of electric shock and potential fire hazard as all terminal are easily accessible and - if you're REALLY unlucky - lethal if your house doesn't happen to have a RCD circuit breaker. Don't try this at home, kids!
No dear no risk of shock in this circuit
If u install it properly
Ye in this way u can shocked due to relay operation
actually kids, your suppose to lick the red terminals to strip em..kids might b stupid but the ones watcin this video know better than to lick the hot side of the panel. so i think were good. btw rcd's or gfci (ground fault circuit interrupter) with variations on that can still kill in jus the wrong scenarios like with somebody with heart problems
Can you tell me please, why do you added the 9v battery? Can I build without battery, or not working ?
It basically blinks the bulb
So it is needed
@@thawzinkhant1759 yeah, thanks...i understand now! What can i do to increase the pause between 2 flashes, if i connect another capacitor in parallel or a bigger capacitor it works ?
@@youtubeexpertyoutubeuser2.760 higher frequency then smaller capacitors and lower frequency - bigger capacitors
Hope it works!
Plese mention that valus of electonisc components used in the ckt, i want do it
Battery q use kiua
What if the battery drain does the bulb will blink again?
How many amps the diodo or part number diodo? Same tutorial is good for 120AC same circuit? Good tutorial.
+Fox 15 dear it is 10 amps relay
Diod 40007
+Fox 15 if u want more amps u can use mor power relay
Speed thodi kam karni ho to kya karna pade ga
good morning , thank Nice
+Valter Souza thanku so much for encouragements
+Valter Souza Thanx dear
+Valter Souza u well come dear
Maime 470 uf 35 volt ka capacitor lgaya blink nhi ho RHA hai Kya kre
Good
Thanx a lot
do you have an amazon link for the components ?
Yes sir I have but I will send link tomorrow
Hi, can I attach 4 lights and make all of them blink together ( want them one second off & one second on).
Thanks
Hello
Did you figure out?
I want to do the same with 20 bulbs
Betry apä bang..?
nice
Thanx for appreciation
plz like my all videos and feed backs
special request : plz share my videos for my sport
How many bulbs can be added in this series
as u wish dear
Circuit please.
In the short time it was blinking, seemed like it was slowly speeding up. Or was that just me?
no dear speed will remain constant if you want ot increase speed use low power capacitor
plz visit my web for more deaill circuits
tinyurl.com/y6fm4d5g
Bhai Capcitor + - nhi dikhaya
Diode + - Connect Capcitor + -
I'm linking circuit diagram dear
sir ji ye light 2 second ke liye on off hona chahiy
Dear capacitor ki value mazid barha dein
OK dear mein try kron ga jald video lagany ki
समजले नाहि विडीओ बनवा ना सर आणि सर्किट चे डिटेल कँपेसिटर कोनते वापरावे हे विडिओ मध्ये सांगा
thanks
Jaldi bataana bhai
bro diode +,- shown wrong
...Some of the worst soldering I've seen in a long time!
I gave tried better in my new videos