Hi, Alexander. I always enjoy watching and learning from you on your videos. I often learn more or catch missed details when I watch your video a second time. Thank you. PS - I like how diplomatic, kind, and polite you are to all viewers.
I just inherited my grandmothers machine like this and am so excited to use it. I’ve cleaned it all up and gave it a good run. I was wondering if your machine bounces when running fast?
That is cool, use it and have fun, grandma will approve. Yes many machine vibrate and/or jiggle a bit at full speed but since most don't sew at that speed I don't think it much of an issue. Maybe when your filling a bobbin just back off the throttle a little bit.
@@AlexanderDyer ،I bought it last week and I can't sew a straight stitch..it always makes zig zag .. How I replaced into normal case.. please can you tell me .
Would this be considered an industrial machine? I would need to be able to see through at least 4 layers of seatbelt webbing without it jamming up. Thanks!
podrias hacer un video y mostrar como estan formados los discos que ya vienen armados,no se encuentra en ningun lado , compre una nechi y me vinieron desarmados. gracias
If you have an exces thread on the bottom on the fabric, that is actuall from loose top thread tension. Watch this video for solution. ruclips.net/video/xax0RTCqYTk/видео.html
Salve ho un problema con la Necchi Super Nova , mi rompe sempre il filo dentro il tendifilo dove si incastra e poi e non scorre più fino alla rottura,ho provato a spostarlo su tutte le misure poi l'ho pulito benissimo dentro i dischetti ma niente da fare neanche con altri tipi di filato, avete qualche consiglio? Grazie.
Just found one like this one today.. someone took it outside with sign saying to give...took it home for my wife,,,does it work well..is it a good sewing machine?
My necchi Supernova ultra c. 1958-60, was just rehauled and I am unable to raise the bobbin thread. It's been a while since I've used it so I need some basic set-up help, please.Thanks so much.
+Leatrice. Robinson Most common problems assuming your timing is correct and it probably is. Make sure you have the correct needle. Check that your needle is properly installed with the groove to the left, scarf to the right. Thread your needle from left to right. Check that your bobbin is correctly installed and leave about a 4 or 5 inch tail to pull up. If all this is correct then it should probably work. Good luck.
You a a machine (and tool guru) learned much from table video...I have the power tools, just need to pass learning curve. You helped a lot. I have basic q; I watched not all your videos, but some home, some industrial machines.....why is it I was cautioned to "always" use the hand wheel to begin sewing? You never do it. Is it possible my myriad of teachers all had poorly maintained machines, which did not turn easily? Maybe belts were needing replacement. I have a Necci BU. Wish I knew age. more research to do.....so far some time in '48 to '53
I am self taught so I am sure I do stuff wrong all the time. What I heard is you should start after first plunging the needle through the fabric. I think, like you, that it helps to keep from stalling a weak motor. Personally I have never seen much of a need for it but to each their own. These are my machines so I guess I get to use them as I see fit. Ha ha, I kid 😊
Thanks for reply. Not a needle issue. I always start (and stop) with needle take up lever at highest point, reduces those snarls in the bobbin case. Although when changing to a different project/fabric, especially with heavy fabrics & larger needle sizes, I do walk the needle down into the fabric and back the first full rotation of a stitch to be certain the feed dogs/presser foot is set and moving the fabric correctly. Prevents broken needles if the bobbin case happens to be inserted incorrectly. BTW I think I saw you inserting a bobbin case in a video. That flipper lever (In my Necchi) does two things, one acts as handle, two, when fully perpendicular to the bobbin it grips the bobbin so it won't move or slip out - most important if you don't fully engage the bobbin case before releasing the lever, that bobbin can slack up just enough thread to cause a snarl and possibly bent or break needle. I watched more of your machine videos. Looks to me like all the machines, and motors need no help starting up, and sewing smoothly, even making the heavy canvas bag you demonstrated. My mom may have made up this rule due to an improperly tension-ed belt, and it just became cemented in her head, and passed on to me.. LOL Kudos for the great videos & projects.
My grandma has this machine and I am trying to learn how to use it. However, the needle will not go on its own and needs help and sometimes won't go at all. Anyone have any suggestions on what I need to do?
Try tightening the thumb screw knob in the center of the hand-wheel. This is a disengagement feature so that the needle doesn't operate as you fill a bobbin.
I have been using that knob to get it to go. If I move it forward and keep going it will sew it but just kills my hand and takes forever! If I go back then forward again sometimes it starts to go automatically?
Jackie Damhoff Just tighten it down and you shouldn't have to mess with it any more. Righty tighty. Maybe you have a weak motor or a slipping belt. You might need to get it serviced, Impossible to say from here.
عندي مثل هذه الماكينه وعايزه اشغلها علي الخياطه العاديه فقط اطبطها ازي ‘ وفيها كمان عيب اخر عند استعمال الماتور يعمل ولكن الماكينه لا تشتغل ارجوا الافاده
Hi Mr Alex. I have ask a favour. To you. Four year ago. Yo have never Reply I will ask again please could you tell me why my sewing machine the same model don't sew fouards any more? Thank you
It is impossible for me to diagnose. Check your feed dogs for loose screw. Check the rotating plate over the feed dogs and check your stitch length setting. That is the best I can do. Good Luck
@@AlexanderDyer Hi! How are you? I've got a Necchi Lycia II sewing machine (which I absolutelly adore) with its instructions... I can email you a copy of it if you want to. Please let me know your email address. Have a great day.
Great video. Thank you. I learn a lot because your video is clear and there's no distracting music.
Hi, Alexander. I always enjoy watching and learning from you on your videos. I often learn more or catch missed details when I watch your video a second time. Thank you.
PS - I like how diplomatic, kind, and polite you are to all viewers.
It's the golden rule.🙂
Nice demo of a great machine. I hope this is the one I just bid oh and won.
Thanks but I sold this one years ago.
Thank you, beautiful machine.
I just inherited my grandmothers machine like this and am so excited to use it. I’ve cleaned it all up and gave it a good run. I was wondering if your machine bounces when running fast?
That is cool, use it and have fun, grandma will approve. Yes many machine vibrate and/or jiggle a bit at full speed but since most don't sew at that speed I don't think it much of an issue. Maybe when your filling a bobbin just back off the throttle a little bit.
That could be the table.
@@mjch293 Good thought. Actual Necchi tables are pretty solid.
@@AlexanderDyer ،I bought it last week and I can't sew a straight stitch..it always makes zig zag ..
How I replaced into normal case.. please can you tell me .
@@nihalhussein2163you probably just need to take a cam out or move the zigzag limiter all the way to the left.
Would this be considered an industrial machine? I would need to be able to see through at least 4 layers of seatbelt webbing without it jamming up. Thanks!
No, this is not an industrial. This is a domestic or home machine. Light, portable and intended for clothing and household items.
Hi Mr Alex I have fix the problem with my machine. Thanckyou very much Do yo live in London ?
Hi, I recently inherited one of these but it didn't come with a foot pedal and the original electrical seems broken.
Wondering if you could help?
Does this help? www.ebay.com/sch/i.html?_from=R40&_trksid=p3519243.m570.l1311&_nkw=necchi+foot+pedal&_sacat=0
Very informative,Just bought one identical to yours and trying to learn it.can you tell me what needle type, I need to get for heavy duty material ?
Your needle size should match your thread size. I found you some good info to start with here: www.singerco.com/sewing-resources/machine-needles
Very excellent closeup demo dream machine🏳️🌈👍👌🏾🧕🏿🦹🏾♂️
🙌
podrias hacer un video y mostrar como estan formados los discos que ya vienen armados,no se encuentra en ningun lado , compre una nechi y me vinieron desarmados. gracias
Señor yo quisiera saber si existen maquinaria cómo está la marca, soy de Perú Lima , quisiera comprar,estoy agradecida x de respuesta, bendiciones ok
Hola una pregunta. Tengo la misma maquina pero el hilo de abajo se enreda todo en la tela . Tenes algún video ?
If you have an exces thread on the bottom on the fabric, that is actuall from loose top thread tension. Watch this video for solution. ruclips.net/video/xax0RTCqYTk/видео.html
Hola buenas tardes como lo pusiste alli creo que el video se adelantó un poquito y no lo pude entender bien disculpa
Ser. Alexander de casualidad sabrá como puedo concernir el transformador de alimentación al motor de la máquina de coser Necchi Supernova como la suya
Salam j'ai une SuperNova mais j'ai pas la fiche électrique ni le manuel ni les accessoires comment et ou trouver ?? merci
Salve ho un problema con la Necchi Super Nova , mi rompe sempre il filo dentro il tendifilo dove si incastra e poi e non scorre più fino alla rottura,ho provato a spostarlo su tutte le misure poi l'ho pulito benissimo dentro i dischetti ma niente da fare neanche con altri tipi di filato, avete qualche consiglio? Grazie.
Just found one like this one today.. someone took it outside with sign saying to give...took it home for my wife,,,does it work well..is it a good sewing machine?
You did well. Have Fun!
Hi Mr. Alex. Is there a video where I can see how to change the belt and which one is the appropriate? Thanks a lot.
nesecito saver como usarla como se.sacadel cajon
السلام عليكم لو سمحت انا عندي ماكينه مثل هذه انا عايزه اعرف اشغلها خياطه عاديه ارجوا الرد او اذا كان لها فيديو للتشغلها
My necchi Supernova ultra c. 1958-60, was just rehauled and I am unable to raise the bobbin thread. It's been a while since I've used it so I need some basic set-up help, please.Thanks so much.
+Leatrice. Robinson Most common problems assuming your timing is correct and it probably is. Make sure you have the correct needle. Check that your needle is properly installed with the groove to the left, scarf to the right. Thread your needle from left to right. Check that your bobbin is correctly installed and leave about a 4 or 5 inch tail to pull up. If all this is correct then it should probably work. Good luck.
+Leatrice. Robinson Thanks so much for the quick reply.
Como puedo conseguir el instructivo de esta máquina que la herede?
Lo conseguiste yo también tengo la misma
Yo tengo el instructivo
You a a machine (and tool guru)
learned much from table video...I have the power tools, just need to pass learning curve. You helped a lot.
I have basic q; I watched not all your videos, but some home, some industrial machines.....why is it I was cautioned to "always" use the hand wheel to begin sewing? You never do it. Is it possible my myriad of teachers all had poorly maintained machines, which did not turn easily? Maybe belts were needing replacement.
I have a Necci BU. Wish I knew age. more research to do.....so far some time in '48 to '53
I am self taught so I am sure I do stuff wrong all the time. What I heard is you should start after first plunging the needle through the fabric. I think, like you, that it helps to keep from stalling a weak motor. Personally I have never seen much of a need for it but to each their own. These are my machines so I guess I get to use them as I see fit. Ha ha, I kid 😊
Thanks for reply. Not a needle issue. I always start (and stop) with needle take up lever at highest point, reduces those snarls in the bobbin case. Although when changing to a different project/fabric, especially with heavy fabrics & larger needle sizes, I do walk the needle down into the fabric and back the first full rotation of a stitch to be certain the feed dogs/presser foot is set and moving the fabric correctly. Prevents broken needles if the bobbin case happens to be inserted incorrectly. BTW I think I saw you inserting a bobbin case in a video. That flipper lever (In my Necchi) does two things, one acts as handle, two, when fully perpendicular to the bobbin it grips the bobbin so it won't move or slip out - most important if you don't fully engage the bobbin case before releasing the lever, that bobbin can slack up just enough thread to cause a snarl and possibly bent or break needle.
I watched more of your machine videos. Looks to me like all the machines, and motors need no help starting up, and sewing smoothly, even making the heavy canvas bag you demonstrated. My mom may have made up this rule due to an improperly tension-ed belt, and it just became cemented in her head, and passed on to me.. LOL Kudos for the great videos & projects.
My grandma has this machine and I am trying to learn how to use it. However, the needle will not go on its own and needs help and sometimes won't go at all. Anyone have any suggestions on what I need to do?
Try tightening the thumb screw knob in the center of the hand-wheel. This is a disengagement feature so that the needle doesn't operate as you fill a bobbin.
I have been using that knob to get it to go. If I move it forward and keep going it will sew it but just kills my hand and takes forever! If I go back then forward again sometimes it starts to go automatically?
Jackie Damhoff
Just tighten it down and you shouldn't have to mess with it any more. Righty tighty. Maybe you have a weak motor or a slipping belt. You might need to get it serviced, Impossible to say from here.
Jackie Damhoff
Ok
Hello Alex, I have the Supernove Julia. I know it has an automatic threader, do you know how it works?
Bellissima
عندي مثل هذه الماكينه وعايزه اشغلها علي الخياطه العاديه فقط اطبطها ازي ‘ وفيها كمان عيب اخر عند استعمال الماتور يعمل ولكن الماكينه لا تشتغل ارجوا الافاده
ruclips.net/video/xdJ9R7SLVZw/видео.html
Hola mi máquina cose sola sin pedal como puedo conectar el pedal a la máquina?
È in vendita?
I need hello,my Maschine'
Cómo enhebrar la máquina Necchi
Hla buen día me podrías ayudar mi maquina no mueve la aguja es la nechi que tienes en el video gracias
ruclips.net/video/xdJ9R7SLVZw/видео.html
Bu makinanin ikinci el olanı satılıyor ve almak istiyorum ama tamiri nasıl yapılır ve nasıl kullanılır bilmiyorum😢
DOVE SI COMPRARE IL MOTORINO DI QUESTA MACCHINA GRAZIE
Ciao io chiedo aiutò o la machina da cucire necchi 267 supernova julia non riesco a lavorare zig zag aiutooo grazie
Mine is super nova Nechi comes with funniutre incorporated
Hola mi maquina no gira la perilla de arriba de discos no se como hacer para q gire solo anda en forma manual
muito bom shows esta máquina tem quanto anos .
+louro araujo Sim. Obrigado por seus comentários. (Google Translate)
Wellington Araujo
Hi Mr Alex. I have ask a favour. To you. Four year ago. Yo have never Reply
I will ask again please could you tell me why my sewing machine the same model don't sew fouards any more? Thank you
It is impossible for me to diagnose. Check your feed dogs for loose screw. Check the rotating plate over the feed dogs and check your stitch length setting. That is the best I can do. Good Luck
What's the deal with the three way swivel plate?
Options
@@AlexanderDyer I know that, I am trying to understand what it does.
Most of those old home machines had several needle plates. For example they would have one for straight stitch and another for zig zag stitching.
Donde coprar el resorte del tira hilo no lo encuentro
Donde comprar el resorte del tira hilo estoy en mexico
Y el hilo de la bobina de avajo a dónde va?
En la bobina, abajo
Buenas noches cómo hago ojales con la supernova
All machines are basically the same, I think this will help you to understand ruclips.net/video/SgWAB4JWtbk/видео.htmlsi=FtpNb2BYo1m147Cr&t=420
Thanck you very much for you info , I will try sorry about my spelling. , Have a good day April 18.2017 Ines Garcia
Will this machine sew leather?
Yes it an with a leather needle, take your time when sewing.
Buenas
Necesito comprar repuestos para una necchi supernova
I know Lycia can sew with a twin neadle and there is aspecial feet for it, can you tell about this item?
hola! donde se pueden conseguir los discos originales de la Maquina, gracias°
John Silva Photo Traveler
Please. Sir. Can you help me with my machine Nechi same models to sew fouards thanks. I hope I hear from you
Alguien me puede explicar como enhebrarla 🙏🏼🙏🏼
Pasando el hilo por los lugares que tienen que pasar
Hola Me gustaría que me pudiera ayudar algien a encontrar el manual de servicio de antemano mil gracias
freenecchisewingmachinefiles.weebly.com/
@@AlexanderDyer gracias amigo me servirá de mucho
@@AlexanderDyer Hi! How are you? I've got a Necchi Lycia II sewing machine (which I absolutelly adore) with its instructions... I can email you a copy of it if you want to. Please let me know your email address.
Have a great day.
Por favor habla ve explicando lo que estas haciendo
Que máquina tan bonita por favor has un video explicando todo lo referente a esta marca de maquinas
Podrías traducir toda las instrucciones.en Español por favor gracias bendiciones
I need hello,my Maschine'
I need hello,my Maschine'
I need hello,my Maschine'
I need hello,my Maschine'
I need hello,my Maschine'
I need hello,my Maschine'