Short and to the point - thanks! One additional tip that I learned about the hard way - note the orientation of the back (in relation to the face) before you remove it. You have to reinstall it the same way or the watch won't beep/chime/alarm. Who knew?
Thanks for this tip, but I cannot hear it because of hearing loss, but it does annoy others when I can't hear it. Now I am gonna install it that way on purpose. 😁
I was recently told I have some hearing loss too and the doctor recommended a hearing aid. I said no because then I don’t have an excuse when my other half says I’m not listening. 😄
Great video. Thank you for getting right to the point and not wasting a minute or two telling us what you like about the watch, how long you have had it, etc.
After scouring the internet for someone with the same battery compartment as me, I FINALLY found your video! Thank you so much!! I’ll definitely save it for future reference 💗
You deserve nothing less than a standing ovation, with many applause. Your perfect and detailed instructions worked perfectly on my Timex Expedition. But on that model there is only one latch, witch makes things easier for battery replacement. Again, many thank's. Merci beaucoup pour les instructions!
Thank you. I am someone who like to tinker but when I went to replace the battery I couldn't figure out how to get it out without taking the whole watch apart. Now I can wear my waterproof sport watch... After 5 years.
Ha! Glad the video was helpful. When I tinker my approach is “I’m either going to fix it or break it.” And if I don’t try to fix it, it eventually ends up in the trash. There’s nothing to lose other than a little time. 😃 Regarding your old watch, I recommend conditioning the rubber gasket with a silicone based lubricant so the watch doesn’t leak and/or fog up.
I decided to restore life to my "Ironman Triathlon M661" (aka SLEEK 250-lap). When I reached step "unlatch to remove battery", I got stuck - until you showed how to press with a pin, alongside the battery-edge, in the clear space of the metal latch. Bingo! Not the same watch as yours, but it worked a charm. Thank you.
Success! Thanks for the instructional video. btw... My grandfather was a renowned clock maker back in the day in Old San Juan, Puerto Rico. He serviced some enormous complicated clocks that are still standing in the Cathedral. So yeah. Failure to change a watch battery was not an option for me!
So glad the video was helpful! The latch/catch is definitely the tricky part. I must have watched 10 videos on changing the battery in a timex ironman and none showed the latch, which was frustrating for sure. Thanks for the kind words and for leaving a comment. Happy holidays!
Great idea! Old watches do come in handy like that and I prefer them. I have a smart watch too and it can drive me crazy unless I turn off all notifications. If I get a text or phone call the phone’s buzzing in my pocket, the watch is buzzing on my wrist, and then I’m irritated. 😁
I watched 2 other videos and yours is the best. I like that it is short, but covers the key things. It was the latch that gave me pause--you clearly showed that I needed to insert a sturdy needle and push away from the center. Also I just noticed that your written description is extremely helpful and detailed. Wonderful job! Thank you!! As an fyi for others, my ironman Timex is a little different than this one (possibly because it's a woman's watch and a bit newer): Re-latching the battery cover after the new battery was in place was slightly tricky in that I ended up using the needle to gently push down on the latch to get it to catch (instead of inserting the tip of the needle as I had done to remove the latch). Also, in order to remove the back panel, I first had to remove at least one of the straps (by getting the pin to release), as the edge of the strap helps to hold the back panel down. I'd also recommend that BEFORE you screw the backpanel in place again, check to see if the digital display is working. If it's not, then your replacement battery might be no good (try a different one). For my watch, the back panel is supposed to snap into position if everything is in the right place. So, take a good look at the edge of your watch before removing the back panel to make sure that you know how tight the pieces should fit together. (The first time I tried to put the back panel back, the pieces were not in the right position and that caused a gap and prevented the back panel from creating a seal, instead there was a gap that would have let water into the watch).
After watching many videos, I finally landed on yours! Thank you so much for the latch explanation, it made all the difference. This is the most thorough video found. Five stars ⭐️ ⭐️ ⭐️ ⭐️ ⭐️ from me!
Thanks so much for the kind words! I probably watched those same videos and after feeling frustrated that no one showed the latch, I figured I’d make a video that does. 😃👍
Thanks for the video. I looked at other RUclips videos, but they did not have the level of detail, especially on removing the latch. I was able to complete battery replacement.
Thank you for the tip at 2:50 (ish) about that small clip that holds the battery - I was struggling to get power to the watch during a battery replacement on a similiar model
Video works also for a T78577 Timex watch. New tip. When I went to pull off the label, the guts of the watch came with it out of the case. Before closing the case, I had to put it back CORRECTLY. This is important. Eventually I figured out the four buttons must not protrude into the case, and must be in retracted position. With a small screwdriver blade, from the inside, I pushed the buttons out. THEN the guts slip in just right. One button popped out entirely, but it was OK by being slipped back in its hole. Also, take care the very thin gasket rubber ring is in its recess. From the start, I worked with the watch on a small tray, with a paper towel to stop parts rolling around. Lost no parts. Phew. Extremely useful. Before I saw this video, I had previously botched the job. After using the video I copied the URL, put it in a text file, and saved it in a directory with the pdf of the Timex instruction manual. One last tip, A previous time I tore up the phillips star slot in the screw. I used VAMPLIERS Stripped Screw Extractor Needle Nose pliers that are designed to really really do grasp the tiniest protruding screw head. Not cheap, but when you need them, oh boy! they are priceless.
Wow, worked like a charm! I thought I would have to take it to a watch repair shop, until I found your video. Really great clear instructions! Nailed it ; ~ 0
Many thanks, Bruce. Great guide. I followed your instructions and everything works brilliantly now, including the Indiglo. As you' ve often found, I didn't need to short the battery, but I see you have another great video about that, just in case. Thanks again.
Regarding 4:12 tightening the screws, the screws should be tightened in a diagonal pattern rather than in a circular pattern. Tightening in a diagonal pattern ensures that the waterproof O-ring gasket receives even pressure whereas tightening in a circular pattern can cause lopsided pressure and thus potential leakage of moisture into the chamber. Tightening in a diagonal pattern is standard procedure for flange assembly as well as mounting lug nuts onto the wheel of a car.
Thanks for the short and accurate vid. I used to change the battery on a Timex Expedition but it was all the same. Easy-peasy once there were some clear instructions...thanks to you.
thankyou, I was going back and forth on whether it would be worth it to replace the battery on my triathlon, watched the video and went into it, got it done with no problem
Thank you so much! I love my Ironman and really didn't want to drop $50 for a new one just because the battery died. I am NOT handy but this video showed that even I could do it and I had no troubles along the way!
These watches can be delicate so if a small piece breaks off or it’s not put back together correctly (for example the back plate is put on upside down) it won’t work.
This was a very clear and well done video. My Ironman is a bit different in that I have remove one of the straps in order to remove the case backing. Both straps lie partially on top of the backing. My battery clamp also has a small screw holding one side down. Additionally mine uses a CR2025 battery.
Yeah, the clip is the hardest part. One thing I didn’t mention in the video is it’s also a good idea to lubricate the rubber gasket to prevent it from drying out and stretching. I use a silicone lubricant and allow it to dry before reassembling.
Regarding 2:26 instead of using a slant tip tweezer, I found that it is better to use a curved hook tip tweezer which can lift off the battery. A curved hook tip tweezer can also lift off the O-ring gasket for cleaning. I clean off the debris around the O-ring as well as the debris which has accumulated underneath the watch back. Also a curved hook tip tweezer is better for holding the tiny screws to position them into their screws holes.
thank you, I had an issue with he watch band overlapping the back cover. I slid it on sideways under the rubber watch band then tapped lightly with a hammer to finish aligning it.
Thanks. I was able to use these instructions to resurrect an old Expedition watch who's battery had gone dead years ago, so now I have something I can tell the time with while I look for a suitable replacement for my Pebble.
If your watch ever malfunctions and you need to reset it by shorting the pads, I've posted a new video. Cheers! ruclips.net/video/oNnxSqQ4hJY/видео.html
Thank you. I only needed to know how the clasp attached. I knew it would be way too easy to destroy it, if I guessed wrong! lol.... good to the point video.
WOW thanks. I got an old timex expedition indiglo from about 1998 from india off ebay as a WORKING watch but the customs description said REPAIR watch so I got duped. Back held on with elastic bands and crown fell out but at least I can EXPERIMENT because I got the BATTERY out so will be able to see if it at least ticks over with a new battery. SLIGHTLY more complicated and they have a second slot for a pin to get the battery out completely.
Great question! I've only had to reset the pads once after a battery change and I've changed the battery at least 4 times without issue. Some folks have said I've simply gotten lucky... perhaps. Either way, if you'd like to learn how to short the pads, see my other video on how to do it (link below). ruclips.net/video/oNnxSqQ4hJY/видео.html
Do you need to put the sticker back on? I finally got the digital movement in the right place after fighting it for a while. I found out I was tightening the screws too hard and it would “shift the movement” and or press the indiglo light on. Therefore making the buttons unresponsive. I forgot to place the sticker back on due to the excitement I got for making it finally work.
I don’t think the “short pads” sticker is necessary . If all the functions and chimes are working I’d say you’re good, but keep the sticker for your next replacement if you’re concerned. If the chimes/beeps aren’t working, that means the back plate is on upside down. There is a shielding sticker on the back plate that prevents the clip from making contact with the metal and if it’s on upside down, there won’t be any chimes. Definitely avoid cranking down the screws. Snug them in. Start each one and then go around or to opposite corners tightening each one gradually until the gasket is compressed.
Great video!!!! Thanks for posting, I successfully changed my battery and I'm glad this vid was here since it was a tiny more complicated than I thought.
Very helpful. Two issues I am having. 1) The band is so inflexible (curved) that it is hard to pin it to a surface. What type of fastener / screws do you use to secure the band? 2) The battery cover is not only secured with four (4) screws, but there is protruding rubber from the band which partially covers the battery cover at both the top and bottom. It extends 1/16 to 1/8 on either side. While I can slip the battery cover underneath on one side, I am unable to pry up the rubber on the opposite side. Wish I could attach a photo. Any thoughts? Thank you.
If you have the same model of watch and are struggling with the band, I recommend removing the strap to make it easier. The watch band is held on with a spring loaded bar. You may want to get an inexpensive watch repair kit on Amazon, which usually has a watch band removal tool.
Thanks for posting this. I followed your method and was able to change the battery. The watch started with 12:00 time allright, however there is one problem, the Set/Recall and Mode buttons are not working so I can't adjust the time. Do you have any suggestion, how to fix this problem? It seems the button when pushed do not touch the metallic part and thus not able to push it inward.
Hmmm. Sounds like something is out of alignment. I’m going to post a video soon on different troubleshooting techniques including shorting the AC (All Clear) pads to the battery . When the watch is open, you should be able to see the buttons make contact with the metal pads inside when the buttons are pressed. Don’t shift the insides around too much though. Also check that the rubber gasket is seated properly around the inside perimeter or else the screws won’t be tight and the insides can move around. Recently my Start/Stop button stopped working. Turns out the metal tab underneath the Start/Stop button came unsoldered. Until my new one arrives, I’ll be using the broken one for time and alarm only. It had a good run though... I rarely take it off. 😃
@@historian2 If you'd like to know how to reset the watch by shorting the pads, I've finally posted the video. Cheers! ruclips.net/video/oNnxSqQ4hJY/видео.html
Thanks for sharing the tape idea. I haven’t gotten a digital expedition yet although I’m tempted ($33 on Amazon). It has a nice profile. While my Triathlon Shock is on the bench for a tear down (it took on sea water because I hit a button while underwater), I’ve been wearing my vintage Ironman... the one Jocko Willink made popular. It’s been sitting in a drawer for 6 years and just needed a battery. What I had forgotten is that a jeweler had worked on it last and dropped a screw only to replace it with the wrong size, which then fell out. Just as bad is when I opened it up, I realized the jeweler had removed the gasket so it is no longer waterproof. I’m now on the hunt for the correct gasket and screw. Regarding alarms, I typically use my phone. I probably have 7 alarms that go off throughout the day for everything from pet meds to breaking for exercise to “stop whatever you’re doing before the kid gets hangry.” Lol
If indiglo was very dim before the battery change, it should be brighter after a battery change. Just be sure to put all parts back together as they were (for example, if you put the back plate on upside down, the alarm/chimes won't work).
This was such a great video! I just got my new Timex Ironman watch so I saw your video on how to set it up (Also a great video)! Usually how long do you need to replace the batteries and does it turn off by itself when you’re not using it?
The watch is always on and battery life varies. When I train regularly or use the indiglo feature often, I typically get 1.5 years although I have gotten longer.
I wish I had found your video before I replaced my battery. I was struggling to unlatch the clasps that hold the battery down, so I searched on google, but did not see anything about it (and did not find your video at that time). I pryed out the latch with tweezers, but I seem to have damaged the clasps. They no longer dependably hold the battery in. I had a terrible time trying to put the back plate back on while holding the battery in place. So sad.
A big thank you Bruce. I was clueless as to the removal of the battery clip. Very helpful and prevented me from damaging the retainer. Thanks again.
Very welcome. Glad it was helpful.
Short and to the point - thanks! One additional tip that I learned about the hard way - note the orientation of the back (in relation to the face) before you remove it. You have to reinstall it the same way or the watch won't beep/chime/alarm. Who knew?
That is correct! I've done that too! Thanks for sharing that.
Yes, thanks Stephen for that comment. I though for sure I had broken my watch. Glad the fix was that easy.
Thanks for this tip, but I cannot hear it because of hearing loss, but it does annoy others when I can't hear it. Now I am gonna install it that way on purpose. 😁
I was recently told I have some hearing loss too and the doctor recommended a hearing aid. I said no because then I don’t have an excuse when my other half says I’m not listening. 😄
It's sad how many of these people that benefitted from this video didn't bother to like it, you rock, thanks again
Ha! Thanks Bryan.
Great video. Thank you for getting right to the point and not wasting a minute or two telling us what you like about the watch, how long you have had it, etc.
You’re welcome and that’s helpful feedback!
After scouring the internet for someone with the same battery compartment as me, I FINALLY found your video! Thank you so much!! I’ll definitely save it for future reference 💗
Glad you found it helpful! 😊⏰👍
You deserve nothing less than a standing ovation, with many applause.
Your perfect and detailed instructions worked perfectly on my Timex Expedition.
But on that model there is only one latch, witch makes things easier for battery replacement.
Again, many thank's.
Merci beaucoup pour les instructions!
Glad it was helpful!
Indeed, sure was brilliant!
Thank you. I am someone who like to tinker but when I went to replace the battery I couldn't figure out how to get it out without taking the whole watch apart. Now I can wear my waterproof sport watch... After 5 years.
Ha! Glad the video was helpful. When I tinker my approach is “I’m either going to fix it or break it.” And if I don’t try to fix it, it eventually ends up in the trash. There’s nothing to lose other than a little time. 😃 Regarding your old watch, I recommend conditioning the rubber gasket with a silicone based lubricant so the watch doesn’t leak and/or fog up.
I decided to restore life to my "Ironman Triathlon M661" (aka SLEEK 250-lap). When I reached step "unlatch to remove battery", I got stuck - until you showed how to press with a pin, alongside the battery-edge, in the clear space of the metal latch. Bingo! Not the same watch as yours, but it worked a charm. Thank you.
Glad it worked out! ⏰👍
Thank you for posting this video. I could not figure out how to get those latches off until I saw your trick with the pin. Much appreciated.
Glad the video helped! 😃⏰👍
Success! Thanks for the instructional video. btw... My grandfather was a renowned clock maker back in the day in Old San Juan, Puerto Rico. He serviced some enormous complicated clocks that are still standing in the Cathedral. So yeah. Failure to change a watch battery was not an option for me!
Ha! Great story! Thanks for sharing it!
Wonderful! Thank you... I had no idea how to release the latch! Your instructions are great!
So glad the video was helpful! The latch/catch is definitely the tricky part. I must have watched 10 videos on changing the battery in a timex ironman and none showed the latch, which was frustrating for sure. Thanks for the kind words and for leaving a comment. Happy holidays!
Thank you! Saved the day in resurrecting an old watch for the teenager to take the ACT without a smartwatch!
Great idea! Old watches do come in handy like that and I prefer them. I have a smart watch too and it can drive me crazy unless I turn off all notifications. If I get a text or phone call the phone’s buzzing in my pocket, the watch is buzzing on my wrist, and then I’m irritated. 😁
I watched 2 other videos and yours is the best. I like that it is short, but covers the key things. It was the latch that gave me pause--you clearly showed that I needed to insert a sturdy needle and push away from the center. Also I just noticed that your written description is extremely helpful and detailed. Wonderful job! Thank you!!
As an fyi for others, my ironman Timex is a little different than this one (possibly because it's a woman's watch and a bit newer): Re-latching the battery cover after the new battery was in place was slightly tricky in that I ended up using the needle to gently push down on the latch to get it to catch (instead of inserting the tip of the needle as I had done to remove the latch). Also, in order to remove the back panel, I first had to remove at least one of the straps (by getting the pin to release), as the edge of the strap helps to hold the back panel down. I'd also recommend that BEFORE you screw the backpanel in place again, check to see if the digital display is working. If it's not, then your replacement battery might be no good (try a different one). For my watch, the back panel is supposed to snap into position if everything is in the right place. So, take a good look at the edge of your watch before removing the back panel to make sure that you know how tight the pieces should fit together. (The first time I tried to put the back panel back, the pieces were not in the right position and that caused a gap and prevented the back panel from creating a seal, instead there was a gap that would have let water into the watch).
Thank you for sharing all that helpful info! 😃⏰👍
Ah the dreaded latch catch. I have the ladies version and your thorough instructions did the trick. Much appreciated! Now for a training run....
Thanks for the feedback. I did this video because the videos I found didn’t provide a good view of unlatching the battery. Thanks again.
The watch people at Walmart couldn't figure this out! Thanks!
Ha! Well, I’m glad the video was helpful. 😃
These instructions work for TIMEX Expedition battery replacement as well. Using the pin to undo the clasp was the key step I needed to see.
Thanks for letting me know! Glad the video was helpful.
Thanks! I can't believe there are 66K views and only 900 likes. Exactly what I need to replace the battery. Thanks again so much!
Very welcome! ⏰👍
Thank you this was very helpful, sales lady at walmart didn’t know how to open the latch and neither could I
Ha! Glad it worked out. ⏰👍
Ugh, I couldn't figure out the latch. Thanks for this video. You are doing God's work!
Excellent. Glad the video was helpful.
Thank you for the clear instructions. I watched a different video but was still struggling because it wasn't helpful. Thanks for doing it right.
Very welcome! Glad the video was helpful.
After watching many videos, I finally landed on yours! Thank you so much for the latch explanation, it made all the difference. This is the most thorough video found.
Five stars ⭐️ ⭐️ ⭐️ ⭐️ ⭐️ from me!
Thanks so much for the kind words! I probably watched those same videos and after feeling frustrated that no one showed the latch, I figured I’d make a video that does. 😃👍
Didn't have a clue how to release this latch to take the battery out untill you showed me.....Thanks!
Glad it was helpful!
Thanks for the video. I looked at other RUclips videos, but they did not have the level of detail, especially on removing the latch. I was able to complete battery replacement.
Excellent! Thanks so much for watching and I’m glad the video was helpful. 😃⏰👍
Thank you for the tip at 2:50 (ish) about that small clip that holds the battery - I was struggling to get power to the watch during a battery replacement on a similiar model
Glad it was helpful! 🕙👍
Thank you. That latch had me confused till I watched your vid!
Glad it was helpful! 😃👍
Glad it was helpful! 😃👍
Glad it was helpful! 😃👍
Video works also for a T78577 Timex watch. New tip. When I went to pull off the label, the guts of the watch came with it out of the case. Before closing the case, I had to put it back CORRECTLY. This is important. Eventually I figured out the four buttons must not protrude into the case, and must be in retracted position. With a small screwdriver blade, from the inside, I pushed the buttons out. THEN the guts slip in just right. One button popped out entirely, but it was OK by being slipped back in its hole. Also, take care the very thin gasket rubber ring is in its recess. From the start, I worked with the watch on a small tray, with a paper towel to stop parts rolling around. Lost no parts. Phew. Extremely useful. Before I saw this video, I had previously botched the job. After using the video I copied the URL, put it in a text file, and saved it in a directory with the pdf of the Timex instruction manual. One last tip, A previous time I tore up the phillips star slot in the screw. I used VAMPLIERS Stripped Screw Extractor Needle Nose pliers that are designed to really really do grasp the tiniest protruding screw head. Not cheap, but when you need them, oh boy! they are priceless.
Great advice and info. Thanks for sharing!
Wow, worked like a charm! I thought I would have to take it to a watch repair shop, until I found your video. Really great clear instructions! Nailed it ; ~ 0
😃⏰👍
Fantastic Instructions!!! Be sure to first assemble the tools as the video recommends. Made changing the battery super simple the first time.
Glad it was helpful! Cheers!
Thanks buddy, that latch had me spooked!
Many thanks, Bruce. Great guide. I followed your instructions and everything works brilliantly now, including the Indiglo. As you' ve often found, I didn't need to short the battery, but I see you have another great video about that, just in case. Thanks again.
Very welcome! 😃⏰👍
Regarding 4:12 tightening the screws, the screws should be tightened in a diagonal pattern rather than in a circular pattern. Tightening in a diagonal pattern ensures that the waterproof O-ring gasket receives even pressure whereas tightening in a circular pattern can cause lopsided pressure and thus potential leakage of moisture into the chamber. Tightening in a diagonal pattern is standard procedure for flange assembly as well as mounting lug nuts onto the wheel of a car.
Thanks for sharing that!
Same procedures with wheel nuts and rim/tire on a Jeep or any vehicle.
Got the back off......yikes. SO glad I found your page made it so much easier. Thank you.
Glad it was helpful! Thanks for leaving a comment!
I thought it was going to be more difficult until I’ve seen this video, thanks.
You're welcome! Glad it was helpful. Cheers!
Thanks for the short and accurate vid. I used to change the battery on a Timex Expedition but it was all the same. Easy-peasy once there were some clear instructions...thanks to you.
Glad it helped! Cheers!
thankyou, I was going back and forth on whether it would be worth it to replace the battery on my triathlon, watched the video and went into it, got it done with no problem
Excellent! Glad it worked out! 😃⏰👍
Thanks Bruce! I needed help figuring out the latch and this video was perfect!
Very welcome! Cheers!
I used your trick to secure the watch and it did help a lot to hold it still as well as the straps out of the way. Nice idea.
Thanks! Glad it was helpful. ⏰👍
Thank you so much! I love my Ironman and really didn't want to drop $50 for a new one just because the battery died. I am NOT handy but this video showed that even I could do it and I had no troubles along the way!
Glad it was helpful. I love my Ironman watches as well. 😃
My watch still doesn't work, I put the new battery nothing the old nothing, what am I doing wrong
These watches can be delicate so if a small piece breaks off or it’s not put back together correctly (for example the back plate is put on upside down) it won’t work.
This was a very clear and well done video. My Ironman is a bit different in that I have remove one of the straps in order to remove the case backing. Both straps lie partially on top of the backing. My battery clamp also has a small screw holding one side down. Additionally mine uses a CR2025 battery.
Glad the video was helpful. What model is your watch? Just curious.
Most excellent video, audio, and explanation! Helped make my battery replacement a breeze.
⏰👍
Great technique for removing the battery clip! I've been mangling those for years.
Yeah, the clip is the hardest part. One thing I didn’t mention in the video is it’s also a good idea to lubricate the rubber gasket to prevent it from drying out and stretching. I use a silicone lubricant and allow it to dry before reassembling.
I just ordered a bunch of watch gaskets. Once I determine the correct size, I’m going to post a full tear down of the triathlon shock.
Well done, thx. The latch had me confused, like others, thanks!!
Very welcome! I made the video because I had watched many videos and none explained the clip... it’s the trickiest part. 😃⏰👍
Regarding 2:26 instead of using a slant tip tweezer, I found that it is better to use a curved hook tip tweezer which can lift off the battery. A curved hook tip tweezer can also lift off the O-ring gasket for cleaning. I clean off the debris around the O-ring as well as the debris which has accumulated underneath the watch back. Also a curved hook tip tweezer is better for holding the tiny screws to position them into their screws holes.
Helpful info! Thanks for sharing!
Your video was excellent! Just changed my watch battery because of this video and your clear instructions! Thank you so much! 🙏
Very welcome! 😃⏰👍
Great tutorial! Would never have figured it out without 😊
Glad it was helpful! 😁⏰👍
thank you, I had an issue with he watch band overlapping the back cover. I slid it on sideways under the rubber watch band then tapped lightly with a hammer to finish aligning it.
Thanks. I was able to use these instructions to resurrect an old Expedition watch who's battery had gone dead years ago, so now I have something I can tell the time with while I look for a suitable replacement for my Pebble.
Awesome! I love my Timex watches!
Thanks for the video, I would never have figured out that latch by myself.
The latch is definitely the tricky part. Glad the video was helpful.
Thank you. Also watch your other video on how to use Timex Ironman. Very helpful!
Glad it was helpful. Thank you for leaving a comment.
If your watch ever malfunctions and you need to reset it by shorting the pads, I've posted a new video. Cheers!
ruclips.net/video/oNnxSqQ4hJY/видео.html
You are a life saver, my friend! Many thanks...
Glad the video was helpful. Thanks for leaving a comment.
Thanks! Was unsuccessfully wrestling with that bracket and was about to chuck the whole watch. Guess I'll keep it now 😄. Subbed.
The clasp is definitely the tricky part. Thanks for subbing!
Thank you. I only needed to know how the clasp attached. I knew it would be way too easy to destroy it, if I guessed wrong! lol.... good to the point video.
Glad it was helpful. ⏰👍
Thanks. Wasn't sure how to change the battery, so your video helped.
Great to hear it helped! Cheers!
Thank you so much for your video. I could not figure out how to get that battery clasp off!!
The clasp is definitely the tricky part! Glad it was helpful.
Thanks, man! Those little clasps threw me for a loop.
They always do! Glad I could help!
Thank you ... the latch unclicking part was most valuable.
Very welcome. Agreed that the latch is the trickiest part. ⏰👍
Pin! That was the trick. I tried the smallest tool bit I had and it was too big. Thanks. Easy enough once that was done.
The pin is the trick. Funny I just ordered a $20 watch repair kit from Amazon, and the only thing it didn't have? ...a pin. Ha!
WOW thanks. I got an old timex expedition indiglo from about 1998 from india off ebay as a WORKING watch but the customs description said REPAIR watch so I got duped. Back held on with elastic bands and crown fell out but at least I can EXPERIMENT because I got the BATTERY out so will be able to see if it at least ticks over with a new battery. SLIGHTLY more complicated and they have a second slot for a pin to get the battery out completely.
Thanks for sharing that story. I hope you’re able to restore it.
Thanks man I was wondering how to take the metal piece inside protecting the battery off
Removing the clasp is the trickiest part! Glad the video was helpful! Cheers!
Very helpful!
Short and sweet and still with easy, great detail.
Glad it was helpful! 😃👍
... and what about shorting the reset pads (as indicated on the sticker) as a final step in the process, prior to putting the cover back on?
Great question! I've only had to reset the pads once after a battery change and I've changed the battery at least 4 times without issue. Some folks have said I've simply gotten lucky... perhaps. Either way, if you'd like to learn how to short the pads, see my other video on how to do it (link below). ruclips.net/video/oNnxSqQ4hJY/видео.html
Thank you! I had no idea how to remove the latch
You are welcome! Glad the video was helpful. The latch is definitely the tricky part.
Thank you for posting this.
Came in very handy.
All the best.
Very welcome! Cheers!
Great video with excellent instructions for an otherwise tricky little battery change.
Glad it was helpful! Cheers!
Thank you for the video! Needed a new battery in my Timex also.
Glad it was helpful!
Clear and concise. Thank you!
Very welcome! Glad it was helpful!
Thank you! Couldn't figure out that clasp!
Very welcome. The clasp is the tricky part. 😃👍
Do you need to put the sticker back on? I finally got the digital movement in the right place after fighting it for a while. I found out I was tightening the screws too hard and it would “shift the movement” and or press the indiglo light on. Therefore making the buttons unresponsive. I forgot to place the sticker back on due to the excitement I got for making it finally work.
I don’t think the “short pads” sticker is necessary . If all the functions and chimes are working I’d say you’re good, but keep the sticker for your next replacement if you’re concerned. If the chimes/beeps aren’t working, that means the back plate is on upside down. There is a shielding sticker on the back plate that prevents the clip from making contact with the metal and if it’s on upside down, there won’t be any chimes.
Definitely avoid cranking down the screws. Snug them in. Start each one and then go around or to opposite corners tightening each one gradually until the gasket is compressed.
Cheers. Wouldn’t have figured it out so tiny clips.
The clip is definitely the tricky part. Glad it worked out.
Great video!!!! Thanks for posting, I successfully changed my battery and I'm glad this vid was here since it was a tiny more complicated than I thought.
Glad it was helpful. Thanks for leaving a comment.
Thank you very much! Your video is a huge help!
Very welcome!
Very helpful. Two issues I am having.
1) The band is so inflexible (curved) that it is hard to pin it to a surface. What type of fastener / screws do you use to secure the band?
2) The battery cover is not only secured with four (4) screws, but there is protruding rubber from the band which partially covers the battery cover at both the top and bottom. It extends 1/16 to 1/8 on either side. While I can slip the battery cover underneath on one side, I am unable to pry up the rubber on the opposite side.
Wish I could attach a photo.
Any thoughts?
Thank you.
If you have the same model of watch and are struggling with the band, I recommend removing the strap to make it easier. The watch band is held on with a spring loaded bar. You may want to get an inexpensive watch repair kit on Amazon, which usually has a watch band removal tool.
Awesome. Exactly what I needed. Thank you for posting!
Very welcome! ⏰👍
Thank you! The pin was the missing trick.
The pin is the right tool for the job! 😃
Just purchased this watch today
Congrats and enjoy!
Thanks for posting this. I followed your method and was able to change the battery. The watch started with 12:00 time allright, however there is one problem, the Set/Recall and Mode buttons are not working so I can't adjust the time. Do you have any suggestion, how to fix this problem? It seems the button when pushed do not touch the metallic part and thus not able to push it inward.
Hmmm. Sounds like something is out of alignment. I’m going to post a video soon on different troubleshooting techniques including shorting the AC (All Clear) pads to the battery . When the watch is open, you should be able to see the buttons make contact with the metal pads inside when the buttons are pressed. Don’t shift the insides around too much though. Also check that the rubber gasket is seated properly around the inside perimeter or else the screws won’t be tight and the insides can move around.
Recently my Start/Stop button stopped working. Turns out the metal tab underneath the Start/Stop button came unsoldered. Until my new one arrives, I’ll be using the broken one for time and alarm only. It had a good run though... I rarely take it off. 😃
@@BruceAlanR Thanks for your reply, will definitely check out your next video!
@@historian2 If you'd like to know how to reset the watch by shorting the pads, I've finally posted the video. Cheers!
ruclips.net/video/oNnxSqQ4hJY/видео.html
Thanks for sharing the tape idea. I haven’t gotten a digital expedition yet although I’m tempted ($33 on Amazon). It has a nice profile. While my Triathlon Shock is on the bench for a tear down (it took on sea water because I hit a button while underwater), I’ve been wearing my vintage Ironman... the one Jocko Willink made popular. It’s been sitting in a drawer for 6 years and just needed a battery. What I had forgotten is that a jeweler had worked on it last and dropped a screw only to replace it with the wrong size, which then fell out. Just as bad is when I opened it up, I realized the jeweler had removed the gasket so it is no longer waterproof. I’m now on the hunt for the correct gasket and screw.
Regarding alarms, I typically use my phone. I probably have 7 alarms that go off throughout the day for everything from pet meds to breaking for exercise to “stop whatever you’re doing before the kid gets hangry.” Lol
Very detailed, good work sir
😃⏰👍
Great video! What I'd like to know is, when you change a battery, would the light "indiglo" feature work again?
If indiglo was very dim before the battery change, it should be brighter after a battery change. Just be sure to put all parts back together as they were (for example, if you put the back plate on upside down, the alarm/chimes won't work).
Thank you! That latch….but now I am good!
Glad it worked out! Cheers!
This was such a great video! I just got my new Timex Ironman watch so I saw your video on how to set it up (Also a great video)! Usually how long do you need to replace the batteries and does it turn off by itself when you’re not using it?
The watch is always on and battery life varies. When I train regularly or use the indiglo feature often, I typically get 1.5 years although I have gotten longer.
@@BruceAlanR great, thanks!
thanks! the pin to unlatch was the key! :)
The funny thing is I just ordered a $20 watch repair kit from Amazon, and the only thing it didn't have? ...a pin for the latch. Ha!
These were perfect! Thanks very much!
You're so welcome! Always happy to know the video is helpful!
Thank for clear instructions
Very welcome! I’m glad it was helpful.
Thanks! Saved my sanity.
⏰👍
Great tutorial. Thanks for sharing.
Very welcome. 😃⏰👍
thanks man...couldn't figure out how to get that clip thing off so I could get the battery out....
Glad it was helpful! Cheers!
Thanks for the great video! You are a BIG help!!! 2 thumbs up
You’re very welcome. ⏰👍
I wish I had found your video before I replaced my battery. I was struggling to unlatch the clasps that hold the battery down, so I searched on google, but did not see anything about it (and did not find your video at that time). I pryed out the latch with tweezers, but I seem to have damaged the clasps. They no longer dependably hold the battery in. I had a terrible time trying to put the back plate back on while holding the battery in place. So sad.
Ugh! Sorry to hear that. I’m glad the video was helpful though.
Thank you. Clearly presented!
😃👍
Thank you.. Very helpful 👍..
Very welcome! ⏰👍
Thank you! Great Work!
Very welcome! 😃👍
Very helpful, thanks!
Very welcome! ⏰👍
Thanks a lot good video
Thanks! Cheers.
Beautiful. Thanks a lot.
You're welcome!
Mine is a t5k351and doesn't have screws but can't pop back off.suggestions
Is there a lip under the back that you can pry it?... gently.
This was really helpful, thank you!
Very welcome! Glad it was helpful!
Just got the watch, good to know
😃⏰👍
thank you - very helpful
⏰👍
Thanks! Exactly what we needed.
Glad it helped! 😃👍
Super helpful! Thank you so much!
Glad it was helpful. Thanks for leaving a comment!