How to Revive Your DJI Batteries - Part 2 More Information
HTML-код
- Опубликовано: 21 авг 2024
- In this video, we'll show you how to revive your DJI batteries using the CP2112 debugging board!
If your drone's batteries are no longer charging, this is the video for you! We'll show you how to revive your batteries using the CP2112 debugging board.
Part 1 - • Revive Your Drone Batt...
Phantom 4 & Mavic Pro - Battery repair video • The Quick and Easy Gui...
Batteries Supported with the CP 2112 Debugging Board
* Mavic Air
* Mavic Air 2
* Mavic 2
* Spark
* Mini 1 & 2
* Osmo Plus
CP2112 Debugging Board Kit - Available directly from us, please email orders@webuydronessa.co.za for pricing & more info. #southafrica #only
The Kit will include,
* CP2112 Board
* Flash drive with the software
* Relative Cables for pinning into the battery.
For International viewers who require the software, NO you are not buying the software ,by donating we will offer you technical assistance via email while you trying to recoveryour batteries , If you do NOT want to donate thats also fine , you on your own then :).Feel free to leave a small donation even if it's one dollar or 10, once donated email us at orders@webuydronessa.co.za and we will We Transfer you the software
Donate Any Amount here on RUclips
Email us once donated - orders@webuydronessa.co.za
Technical Support - repairs@webuydronessa.co.za
Thank you for watching, please consider subscribing it really helps the channel
Thanks, you guys are amazing!!😎
Thanks!
Thanks, it's very helpful info
On a Spark battery if I get the error, just connect external power brick 12v 1.5A to the LHS(next to SCL) pos and neg pins and let it charge for a bit and the error will go when wired up and connect to software... No need to perform "open heart surgery" with battery.
Hi @bobf3598. That does work when there is enough voltage in the cells correct. Unfortunately it is not always the case, and the battery will have to get opened to " wake up " the cell if too low. Those pos and neg pins go through the BMS first, so if the BMS has switched off the CHRG/DSCHRG parameters, then it will never push voltage through to the cells.
most detailed video :)
Danke!
Heh Dave; thanks so much for sending over the software, much appreciated. I will post here results, good or bad!
Only a pleasure Greg , let us know if you need any assistance
am grateful
Any chance for this to also work with the DJI FPV Drone battery? I have a couple that went "all lights blinking" and won't charge. :(
Not at the moment , but hopefully in the near future yes i am sure.
Hey guys, I got the dji battery killer software from you. It’s about 8 files, but I can’t get it to open and install. I think it may be missing a file. Can you provide some better clarity on how to proceed? Seán
I disassembled my Mavic Air batteries and charged the 3 cells in each one "by hand" with a 5V supply until they were over 3.6V - that was enough for one battery to remove the PF1 and PF2 flags according to the procedure via the app. But for the other two batteries at that voltage - even up to 3.8V - the app returned the message "ERROR: Could not perform SMBus read 0x00". Those two batteries needed the extra "jolt" of being momentarily connected to the original charger (until the charger light turns red) before I could overcome the error and continue through the "Unseal->PF1 clear->PF2 clear" sequence.
Same question here before i buy it myself
Perfect. And correct, if the voltages are good, and you get the read error, either plug into original charger for a few seconds, or short the positive most pin of the last cell in the series with the positive pin on the charging port of the battery for 2 seconds. Either way works. This "wakes" up the BMS and the CP will then read/write etc as normal. Glad you got it sorted
@@hkprogram837 Hi. What question do you have?
Great Info,thanks, where can I download software please 🙏
Did you manage to get the software?
Thanks
I have two Mavic 2 pro batteries which are unused but refuse to take a charge. They have been on the shelf too long I think. Can these be revived with the methods shown here
Hi
The method for Mavic Pro batteries is in this video. ruclips.net/video/kg1g2aWtz4Y/видео.html
@@AshrafRogers thanks. I’m a bit wary of cutting open a lipo battery 😨
Mavic 2 Pro batteries do not need to be cut open , they actually open relatively easily
@@webuydronessa good to know. Do you have a video showing those being opened? I’ve already donated just hoping to see the software soon
HI i WOULD LIKE TO BUY THE TWO BOARDS FROM YOU PLEASE THE DE BUGGING BOARD AND ALSO THE BATTERY BOARD FOR THE MAVIC AIR
Thanks for the video. I have 2 spark batteries that the software sees, but both error when clearing PF2. All other steps work fine, just "Clear PF2" errors and then no change when charging. The software gives me an "ERROR: PF2 is not active" message.
Hi. So what steps do you follow?:
Read Info - unseal - Clear PF 1 - Seal.
After clearing PF1 a light on the Spark battery should slowly flash. Then switch off the battery in which the led light on the Spark battery will flash rapidly, indicating successful reset of the BMS. Then put the battery back on or put on charger.
If you clear PF and you dont see the light flashing quickly, clear it again.
Also Note, the voltage of each cell needs to be 3.5v at least for the PF to clear successfully. So total voltage minimum 10.5v minimum
When connecting the Mavic 2 battery and the CP2112 communication port, a message like this (ERROR: Could not perform SMBus read 0×00) appears and the connection is not possible.
Hey. Apologies for the late reply. Have you managed to sort it?
If not, you might need to give the battery a small charge with the original charger just to " enable " it. This only needs to be plugged in for 5 seconds or so. Thereafter unplug and plug back into the CP2112 board and check. Failing that, the cells might be too low for the bms board to function. The cells should ideally be 3.5v each. This can only be determined by opening the battery itself and manually checking each cell. If you are still stuck, give us a shout. Thanks
Is there a chance you can make a debugging board for the TB60 batteries I have 3 dead pairs, not swollen and they didn't even get to 100 cycles (they are supposed to give 200 cycles)
Hi,
you
Thank you!
I’ve gotten “device successfully opened device successfully configured” but can’t read info or unseal, am I doing something wrong?
Hi. What model of battery? What error do you get when trying to read the info?
Also, the cells for the battery need to be at least 3.5v per cell, thereafter the software will read it no issue and you should be able to clear the pf
Will it work with Ronin-M battery?
Hey there, I have donated, but received no code for the software only donation receipt.
Thanks very much, please email us at orders@webuydronessa.co.za
Guys !! dead batteries you only need to disconect the cable from the cells that go to the board or if its soldered , desolder it and solder again !!! I done that to many old fimi v8 2018 versions !!!
This does NOT remove the PF Flag on the BMS board , this method has to be done with DJI batteries , if you do not remove the PF flag the BMS board will not allow any voltage into the battery , yes maybe your procedure works on other brands but not DJI
Getting SMBUS read error, have tried to power +/- pins from external power supply with 9 and 10V, to no avail. What else to try? Cells seem to be drop dead, stored for 2 years, pbly too low to even let the supply voltage get through to support the cells 😞
Hi. Unfortunately if is does not hold any voltage at all, then those need to be discarded yes. Depends on the battery and cell count, 15~17 volts is needed to get the 4 cells up if its a Mavic 2 battery. This would allow them to get to the "required" 3.5v per cell which equates to 14v. Then the CP2112 will easily get rid of the PF flag and re-enable charging etc.
Thanks
Need the software. Gave a donation. Have the confirmation. Didn't receive password to download. What now?
You need to email us at orders@webuydronessa.co.za
hey south africa got snow yesterday!!!!
please how can i get this board?
any joy with the mini 4 battery's
u know how to reset cycle count..??DJI MINI 2
Yes we do
I made the connection without opening the battery and connected it together with its charger and was able to restore one, but my other battery recognizes it and reset its parameters with the software but it still does not turn on its LEDs or charge, what could it be? is for mavic 2 pro and the battery model is FB2
hi.. nice video... any chance to work with matrice 300 / 350 battery? thanks. best regards from Argentina.
Unfortunately not
Does anyone have a solve for the DJ Mavic 2 Pro Batteries that fail because they haven't been charged?
Yes this method works for them too
Hi
Thanks for videos,
I'm one of the unfortunates that has 2 mavic 2 batteries that won't read, so I'm opening them up.
You say in the video put voltage into to the battery slowly, so I'm sure are you starting with low voltage or amps your not specific with the settings.
Thanks again
Hi. So for a Mavic 2 battery, I believe max charge is 17v +-. I usually use about 16volts, but minimum amps. I go about 0.50 amps. Slowly get it up to about 14.2 volts (each cell minimum 3.5v ). Thereafter the CP will detect it and is also safe to clear the pf flag as the voltages are above the needed requirement before flagging. Just be careful making sure you have the poles correctly for charging the cells collectively.
@AshrafRogers brilliant thanks just got one back to life I did 16.5v 0.5amp 30 mins.. if only the cases opened easier, that's the hardest part
i click the Unseal and then Clear PF2 , and Smoked / burned the CP2112,
WHAT 😕 !?!? Was everything connected correctly?
@@webuydronessa yes this is insane and believe me , i am super experienced with CP2112 and electronics in general , the sequence was the cause?
@@webuydronessa the issue was that i connected the VCC to the Battery +
@@gc9n Thats so unfortunate. Never ever connect VCC on the CP boards for this procedure.
Hello, please what is the name of the cable/connector to link de card ev2400 to other card ? Where I can buy it ? Have you got a link ? Thank you
Hi. The ev2400 can only be used with TRB software, which no longer exists. The CP2112 board is a fraction of the cost, and the software needed as in above video works for almost all models anyway
hey my Spark Batteries fully charge but ''fly time'' is about 10 minutes. will the cp2112 reset my batteries back to factory? the 3 wire plug, am i going to use a USB CABLE ? and are all usb cables color coded the same? just want to know which usb line is which,,,thanks
Hi. Unfortunately you cannot get capacity back with using the CP board. The cells are ultimately a consumable item and suffers from wear and tear. Im unsure what you mean regarding the usb cable, not all usb cables have the same color coding. Thanks
Thanks! Can I get the firmware please 🙏
I made a donation to get a password to download software -- and havenot recived any password is this a scam????
No its not a scam ! Have you emailed us at orders@webuydronessa.co.za
Hi what about if i want to make battery mode with 3600mha or 4000 mha battery cell,it can be created battery with Mavic Air 2 and 2s cell. Do i need software for the capacity of 3600mha or 4000 mha
Can be done yes, but only capacity change. You can change cell count but the firmware of the device would need to be hacked to allow no errors from the BMS.
Download the last public version is February 2022 called "dji battery killer"
Hi thanks for the vid. Would like to try this out. Sent my donation and needing the password. Thanks
Thanks very much , password has been emailed to you
Hi good day, i followed the instructions step by step ,but what i have noticed, the battery voltage for each cell is over 3000mv in the video. I have a brand new mavic 3 battery and cells 4 and 2 read ,1 and 3 read 790 mv . Unsealed cleared the pf and pf 2 , got the first led to blink when i pressed cleared pf2 then it stopped. Any help will be greatly appreciated
Hi. Battery cells will need to be balanced. The reason the pf flag triggers, is exactly due to voltage differences. Minimum cell voltages for cells are 3.5 for the pf to be cleared and for it to be able to be charged normally
@@AshrafRogers how to get them balanced ? I would like to get this battery working
@@bernardharewood1686 Please send an email and i will give a more detailed explanation. Details are in the description
@@bernardharewood1686 You first need to charge the 1 and 3 cells until they are around 3.5V to match the 2 and 4 cells.
@@stevehoge how do i do that without opening the battery
Hi, I have purchase this board. But could not find app. Can you send me any link or app file, please.
Hi. Did you send us an email? Thanks
do you have to solder the cp2112 debugging board with the pins mine came separate?
Hi. Did you manage to get sorted with the above? Thanks
Hello friends.
I bought a mini 2 and after the first flight I went to recharge the battery and the following message appeared:
"Battery error. Contact DJI support. ERROR 30074"
Also appeared:
"Battery cell damaged, discard battery and contact DJI support. error 110004"
That's why I came here and purchased the items to try to recover my battery that wasn't charging.
I managed to carry out the process in this video but unfortunately I think that there is no solution for my case. Because 2 cells are dead for some reason.
Battery Cell 1 Voltage = 4079 mV
Battery Cell 2 Voltage = 4308 mV
Battery Cell 3 Voltage = 0 mV
Battery Cell 4 Voltage = 0 mV
Does anyone know if it is possible to do something in this case?
Hi. Apologies for the late reply.
No, the mini 2 uses a 2 cell battery, so it showing 2 cells @ 0v is normal. The problem you are having is you need to balance those cells. 4.3v and 4.0v is a big difference and the BMS will activate the PF flag every time. Once those 2 cells are equal in voltage, then that battery should be ok. You will need a balance charger to do that
@@AshrafRogers Hello friend. How to balance a DJI battery? The closest I found was the imax B6 V2 but I don't see how to make the correct connection to charge and balance the battery. Will I need to open the battery to balance the cells?
Thanks for your response.
@@Djalma_JunioHi. Send us an email and I will send you pics of where and how to connect the balance charger. Email is in the description.
Good morning, how do I get the software needed for this? Thanks
Please email us at orders@webuydronessa.co.za
error could not perform smbus read 0x00 dji spark help me
Then the battery voltage is to low for the board to read , you need to get the battery voltage up on all cells before attempting to read it
@@webuydronessa It also does not work with the charged battery. Any advice? It is a Mini 2 and there is no power button either
@@kangaroo-nm5nn Hi. Have you managed to resolve the issue you have with the mini 2 battery?? If not please send us an email. Thanks
i need it urgent
Did you guys ever get my email? Can you please respond as soon as you can. Thanks you for your help. 👍👍👍
Hi,made a small donation.can I get the software please? Thankfully
Thanks so much , sure please email us at orders@webuydronessa.co.za and we will We Transfer you the software
Я не знаю вашего языка,но в видео интуитивно всё понятно,нет лишней воды.При перепаковке батарей происходит его блокировка,но мне при разблокировке надо ещё прописать новую ёмкость,например было 2250 ма,а надо выставить 3500 ма.Если вам не трудно,могли бы мне объяснить пошагово как это сделать.Заранее спасибо,всего вам хорошего.
Hi. If you need to change the capacity due to new and different cells replacement, you can use the newer version of Battery Killer to calibrate and change capacity etc. We will be posting a video on how to use the new version very soon.
Thanks
@@webuydronessa Спасибо за ответ,буду следить за публикациями.
I sent you an email, and I'm hoping you can respond as soon as possible. It's regarding a donation. Thanks again for your help. 👍👍👍
I did not get my password. Is this a scam?
Have you emailed us at orders@webuydronessa.co.za
No, it's legit! I got my download from them successfully but it's also available on other websites if you search for "DJIBatteryKiller".
No I did not sent email to you
Ok just pop us an email , once we have that we will We Transfer you the software
I payed a dentation of $4 to get the password to down load the program and I GOT NOTHING THIS IS A MONY SCAM RIPOFF
It's definitely not a scam ! Have you emailed us at orders@webuydronessa.co.za ?
Our emails and website where down for a few days this week due to the hosting server having crashed , if you did email it might have gotten lost, please email us and we will send you the software
Is there any way to also know the battery chip?
Thanks!
Danke!
Is there any way to also know the battery chip?
Thanks!
Thanks!