I really liked this video. You made no assumptions of my carpentry knowledge. You laid out every detail fully. I like the easy tips that made the installation easier. Good Job.
I have a kitchen island with two doors on the bottom and two drawers at the top. The drawer on the right is fine but the drawer on the left always falls off the track. Since there is no divider wall in between the drawers, the center slider tracks just hang in midair attached to a plastic backing plate at the rear. I replaced the bottom mount brackets on the drawers and the side brackets (they are actually not attached to the side panels either just hanging in midair) and I put the drawer back and now the drawer is stuck about 2/3 of the way in. I can't pull it out or push it in any further. It looks like it came out of the track so I pulled out the backing plates and it still won't budge. Any ideas how to get it out or fix it?
yeah as long as you know the sizes you need. I would keep a close eye on them to ensure its the right measurements. I've heard they can be pretty sloppy with cuts lol
Fantastic job...!!! Im sure your wife is VERY APPRECIATIVE...thanks for putting this video up...will have to DIY this myself with minimal tools...I dont have a handy husband to push around...!!!! Just kidding Jess...😂
I’m not a wood worker at all, but thanks to following your video step by step, I now have a solid new drawer from scratch. Thanks.
Heck yeah! Awesome job 👏🏻👏🏻👏🏻 sounds like your a woodworker to me
I really liked this video. You made no assumptions of my carpentry knowledge. You laid out every detail fully. I like the easy tips that made the installation easier. Good Job.
Nice man. Much better drawer getting that full 21, now Jess is going to have replace them all just watch. :)
The 3in1 Workshop 😆 don’t you say that! Lol
Great vid! There are a bunch of ways to install slides but yours was new to me, I like it. Oh, and be nice to Jess! 🤨😅
thank you! there is sooo many ways to make drawers and install slides it blows my mind and theres no harm in friendly banter haha
Excellent video making something that seemed harder to me more able to try myself now, thank you.
Thank you!!
You nailed it in the intro. Good job!
😆😆 thanks
Great video good quality voice over
Mark. TheBuilder thanks I appreciate the compliment 😁
Nice I wish I had someone to redo my kitchen
☺️☺️ thanks for watching 🙌🏼
I watched this video to see the dog. The boots!!
hahaha fair enough!
😂😂😂 not the beginning haha
You're going to piss your wife off more when you scratch her glass stovetop. Protect your surfaces, dude LOL
👌👌👌
🙌🏼🙌🏼
Hi
My drawer box is 19”
Do I need 18” or 20” slides
Thanks
If the inside of your cabinet is 19” i would use a 18” drawer slide
Yeah I'll just use that massive saw table I have lying around
any table saw would work. You could even use a router bit. No need to be negative, there’s many options
Slide update. Sounds like you went from a Honda crx to 454 Chevelle. 😂
lmao 454 chevelle allll day!!!
I have a kitchen island with two doors on the bottom and two drawers at the top. The drawer on the right is fine but the drawer on the left always falls off the track. Since there is no divider wall in between the drawers, the center slider tracks just hang in midair attached to a plastic backing plate at the rear. I replaced the bottom mount brackets on the drawers and the side brackets (they are actually not attached to the side panels either just hanging in midair) and I put the drawer back and now the drawer is stuck about 2/3 of the way in. I can't pull it out or push it in any further. It looks like it came out of the track so I pulled out the backing plates and it still won't budge. Any ideas how to get it out or fix it?
Can I have them do the cutting part for me at Home depot?
yeah as long as you know the sizes you need. I would keep a close eye on them to ensure its the right measurements. I've heard they can be pretty sloppy with cuts lol
Fantastic job...!!! Im sure your wife is VERY APPRECIATIVE...thanks for putting this video up...will have to DIY this myself with minimal tools...I dont have a handy husband to push around...!!!! Just kidding Jess...😂
After he dissed her on RUclips?! I don't think she appreciates being bad mouthed all that much.
👍👍
Thanks!
@@TwoMooseDesign You're welcome. Take care.
Too much for me. I need to go to school for this
I noticed you had enough money to spend on fancy equipment for your shop area that you use.
yes? I build furniture for a living. thanks for noticing
😂