Sinclair Garage
Sinclair Garage
  • Видео 21
  • Просмотров 240 320
Dodge Ram Heater Core Flush
My 2009 Dodge Ram has been blowing warmish air for a few weeks now. This video I'll be flushing the heater core in attempt to restore maximum heat. I also will be flushing the entire cooling system and replacing the thermostat and then refilling with new antifreeze. Lastly, I'll be installing a new blend door actuator since the current one sounds as if it has stripped gears when operating.
Просмотров: 119 048

Видео

New Wheel Bearings & Motor Mount Saga
Просмотров 875 лет назад
Installing new axle bearings in the Ford 8" and also explaining the issue with 1967 Mustang 289 engine mounts that are specific to 1967 #FordMustang #1967Mustang #ClassicCars
Yukon Paint Peeling! Tailgate Applique Fix
Просмотров 5826 лет назад
25k miles and already have paint peeling issues!? I show you how I fix this without having to pay the body shop big bucks. Not for everyone, but I'm happy with the results
Making My Jeep Great Again!
Просмотров 66 лет назад
I start to tear down my Jeep for a refresh. It's time to repair some rust and then repaint the entire body. I give an over view of my plans for the Jeep.
Brake Caliper Piston Dust Boot Replacement
Просмотров 23 тыс.6 лет назад
I'm all about saving money, so we replace the piston dust boot on the caliper versus replacing the whole caliper. It's a fairly straight forward install that sounds worse than it really is
Mercury 90hp Carb fix Getting the Pontoon Lake ready!
Просмотров 50 тыс.6 лет назад
Summer is here and it's time to hit the water. Replacing carb floats and changing lower unit oil on Mercury outboard.
Mustang Clutch Install Wrap Up!
Просмотров 6 тыс.6 лет назад
Finishing up the Clutch job in the 1967 Mustang. This video will include installing the flywheel, SPEC clutch, ARP pressure plate bolts and then bolting the transmission back up.This will end the winter upgrades that I had planned and we will move to the next project!
I could have lost a wheel! Trailer bearing replacement
Просмотров 166 лет назад
How to replace the bearings on a untility trailer.
You Need To Try This! Getting the Mustang ready for the new Clutch!
Просмотров 856 лет назад
We continue on phase 2 of the Mustang winter refresh. Modifying the exhaust and removing the pilot bearing in a cool cheap way.
What I have got myself into? Removing the transmission
Просмотров 1116 лет назад
Removing the T-5 to track down high RPM vibration. Throwing in a fresh clutch and other routine maintenance items while it's pulled apart.
I can't catch a break! Another Leak!!!
Просмотров 1616 лет назад
We tear into the front of the 289 to fix antifreeze leak
Garage Check! What Tools do I use?
Просмотров 116 лет назад
I give a walk around of my garage and show you what tools I use.
Part 5 IT RUNS!!! 289 Engine Finale
Просмотров 2,3 тыс.6 лет назад
The 289 is back together and ready for it's first start up!
Part 4 of Mustang 289 Engine Assembly Installing Pertronix Ignition
Просмотров 1,6 тыс.6 лет назад
Installing the electronic Pertronix ignition on my 1967 mustang 289
Part 3 of Mustang 289 Engine Assembly Installing Intake Manifold
Просмотров 7 тыс.6 лет назад
Installing the Edelbrock 2121 aluminum intake manifold
Part 2 of Mustang 289 Engine Assembly Setting Valve Lash
Просмотров 26 тыс.6 лет назад
Part 2 of Mustang 289 Engine Assembly Setting Valve Lash
Part 1 of Mustang Engine Assembly Installing Heads
Просмотров 1,6 тыс.6 лет назад
Part 1 of Mustang Engine Assembly Installing Heads
Mustang Engine Tear Down -- Additional Issues Found
Просмотров 1,9 тыс.6 лет назад
Mustang Engine Tear Down Additional Issues Found
It's time for some winter maintenance!!
Просмотров 76 лет назад
It's time for some winter maintenance!!
Mustang is down for the winter :( Blown head gasket
Просмотров 4336 лет назад
Mustang is down for the winter :( Blown head gasket
Hello Youtube!
Просмотров 186 лет назад
Hello RUclips!