Видео

Thanks for sharing your knowledge

Hey Steve great video. Watched it through and have one question. The hose that's coming out of the skis engine compartment goes into where exactly? I have the same 2 skis but they don't have a hose like that

Hey I own an Indy 500 swapped trailblazer quad. I was wondering if these have crankcase oil and if so how do you check and change it?

Hey I own an Indy 500 swapped trailblazer quad. I was wondering if these have crankcase oil and if so how do you check and change it?

Can’t you just cut the wires at the trim senders and splice them? This would be after verifying the pass through wires are good.

Thank you for this video. Save myself 😅❤. We out of dishwasher liquid and I tried dawn soap and ended up with lots bubbles and caused of this error... I watched your video and able to fix it before I tell my husband what happened 😂😂😂. Thanks again

Amazing video Sr. Congratulation!

That is an ace guide! Thank you. I have a 2008 130 GTi and plan to put a SOLAS on over the winter.

man i was confused, the GE fridge i'm dealing with has much thinner and has a half drawer compartment that I fit stuff in but next time I opened it there were icecubes ontop of my things. I'm surprised how much real-estate they use for this icecube drawer.

Thanks a million. I saw your video after getting a $300.00 estimate for repair. You made the steps so simple and easy I thought, I could do this!!! My boyfriend got back from the gym and I said let's try this!!! we did and succeeded!!!

This GE bomb should be labeled, " SHIT BOX FROM HELL." I've never encountered an ice maker so difficult to work with.

Thank you 😊

Hey question. Did you have a blinking green light? When I do the factory, reset my icemaker will make ice, but it won’t dispense it. Light will stay green until it’s time to dispense then blinks green letting me know there is an issue.

How do I remove the heater tube assembly from the top of the freezer? I wiggle and giggle it but it does not come out. Looks like it should just slide out. Part is wr02x20621.

Jst ordered the very same model for similar reasons. THanks for posting the help!

What’s that plastic yellow piece?! That’s where mine is leaking

Tie a string around cord end to pull it through the upper cabinet hole, if u are alone! I put a sturdy box on the old metal plate, over the stove, to hold the microwave up higher. Put a towel under the metal plate to orotect stove top. Then I may prop it up higher with books, to reach the correct heighth, so it can be screwed in while resting on box.

You just convinced me to get a vasectomy.

My old boiler looks similar to this one, and it's leaking slowly today. I wasn't sure if I could just replace the valve as I did on other water lines since the drain valve is attached directly to the hot boiler. Thank you for the video and now I can replace it the way you did with confidence!

Did you reuse your old holes or drill new holes being you used smaller screws? Thanks!

Hi. We have a part that may fit your machine. We're happy to offer you the product completely free of charge in exchange for a video review. Are you interested?

College student here who used dish soap and was scared to annoy the landlord - thank you SO MUCH for this tutorial. People talk about how environmental or social activism can help make the world a better place, but this tutorial is right up there in my eyes 😂

DuBuque Station

Well covered. Thanks..

Второй год хожу с неисправным тримом вы меня вдохновили на замену

Casey Lane

Well done video !! Thanks!!

Video helped me realise I'm going to buy a different brand to replace my leaky GE

Watching a number of these broken cable videos lead me to believe these are fatigue failures. Many flexes cause the cable to crack. Solution: engage the cable only once per day. If you come to a place where you would stop the blades from turning (loose rocks, etc.), just leave them turn and raise the deck to clear instead.

I just made 4 of these docks! I used 12’ 2x8s for the frame. The movable winch is genius engineering! They work great. I appreciate these videos with creative ideas. Nice job and thanks.

You're the man!

Thanks man

August 2024. Just bought a brand new one of the same model. NOTE: have a small torx driver handy. The screw on Steve’s junction box was Phillips head, but mine was torx. And I had to initially break it loose with a wrench to keep from stripping it.

Thank you for a very clear and concise presentation.

STEVE - I looked all over to find info on the handle for this dishwasher. Thanks for your easy to understand and calm presentation. MUCH appreciated!

You had us at Step 3: Moving the cat!

Great explanation

Steve, can’t thank you enough for this install tutorial on the Whirlpool WDT750SAKZ3 ! Very professional, great job ! 👍🏼

Thank you so much for the tip I fixed my dishwasher

A good method to remove the wear ring is to use a blow torch just and heat it up and use a flat head screwdriver to pry it it comes out easy

I have similar issue but it was cut with some gap, how to replace whole flat one

Thanks....got the same dishwasher coming next week...now I know what water line I need to buy, thanks....ps: by your right hand jewelery, you"re an engineer...me too buddy.

Thank you. I couldn't figure out how to connect my water line. I was about to go crazy 🤪. Thank you buddy!

Brotha, thank you for this video and thank the universe for the contributors that helped you with figuring out a solution. I was about to go buy another coffee maker lol

amazing vid my dad got a new dishwasher after I used it, i got this error. Managed to fix it before he got home and now I don't have to get yelled at as he's none the wiser plus now when it happens to him I can say "maybe its the drip tray"👍

It’s been 4 years. Has the freeze/thaw cycle moved anything?

We’ve had the newer version of this model for about two years and ice maker stopped working a few weeks ago. We replaced the ice maker thinking that was the problem, but still no ice. Looks like we’ll be trying this next. Thanks for the informative video.

I've been roofing for almost 50 years. First thing you should have read the instructions, should have at least 5" offset .You said you used 6" offset, looks like 3" at the top to me. Someone said you put your nails too close, that's because your joints are too close. You voided warranty. Actually, you vary with your joints. Those nails should be 1" from the end. That looks like a 5/12 pitch to me, easily walkable to me. I just roofed my house 7/12 and 9/12 pitch. I walked the 7/12 but used jacks on the 9/12. A little steep but I have seen people walk them. Would make me a little nervous if is 3 story. I hope you don't take this personal, you're a good guy for trying to help people. Maybe you should watch video and read instructions first and learn the safe way. This can be dangerous work. I have seen people fall more than once. Luckily nothing serious. There has been results of people dying from falling from roofs. I always say work smarter, not harder. But #1 is safety first.

I have that door part 2 on list GE dishwasher my brother put extensions on both sides for that flap since it's not a part you can get. It's been riveted on and part of the door. Mine is still leaking but you've give me some ideas.... Thanks. You are very analytical person, patient, and somewhat relentless! Good for you.

Great video , it helped me tonight to fix the same problem. Thanks