Видео

Why do you swap these out for a RoyPow in a later video?

How do i order a sensor from you?

I have a club car 48 volt why does every time i plug my power drive 3 charger in it hums real loud and trips my breaķer

I have an 07 CC with 4/12v batteries. Instructions talk about a blue wire connector under the cover in the battery area. Mine doesn’t have it. What do I do?

Great video. I bought a after market turn signal kit and im having a hard time getting the 9 pin connector on. I finally got it on. Followed there instructions. Cant get the lights to work. Is there a easy way to remove 9pin connector? Not sure if i have the 9pin connection the right way. The color wires aresnt the same on the connectors. Its a 2015 club car . Thanks for any info.

could you not just individually charge the on bad one with an automotive charger and see if that changes anything

Much thanks Wayne! Your blue & white wire splice worked for me. After installing a LiFePo4 battery, my cart was dead - with no idea how to fix - until I saw your video. Absolutely thrilled!!

Well done very informative

How do you confirm without a doubt that your batteries are just no good and need to be replaced? I charged one 8 volt battery for 10 minutes (because i was afraid of blowing it up) with a 12v charger and it got to around 5.6v but it kept dropping after removing the charger...did it need more time charging or is that a sign that the battery is no good?

I’ve got an 03 club car ds iq. I am trying to convert it over to lithium. Based on what I’ve seen and read I have the same cables as the precedent. I have jumped the blue and white wires, removed the other wires and OBC, and have connected it back together per your instructions. I connected the battery and have full voltage across the solenoid and to the motor even with the key out of the ignition. Furthermore, the cart will not move in forward or reverse. Have you seen this issue and do you know what the fix is?

Hey Wayne, good evening I’ve been texting you in regards of a power drive three my DCmeter seems like it’s stuck on 15 plugged in or unplugged. I do not hear a humming sound. I tested everything with a multimeter everything seems like it’s working or it has an home reading. I didn’t want to disturb you by texting you. I watched quite a few of your videos had subscribed wondering if you could help me out seems like you’re also in California.

Great video. Thumbs up!

What if charger does not stop charging? What is wrong? OBC?

Unlike others in your comment section, I wouldn't say "Perfect video", but I would say perfect content. Your camera operator has the shakes big time and makes it very difficult to view for long periods of time, making me dizzy lol. Anyways, thanks so much for the info, its exactly what I needed. Cheers !

My cart comes to a stop and the battery's our at 48 volts and I let it set for a while it runs and then comes to a stop again.

Wayne, thanks so much for the help you gave me yesterday with my battery and charger issue. I appreciate you sir.

Can this be done with. Lithium batterys

I replaced my mcor on my 2014 precedent but it still won’t move any ideas?

Wayne I have a club car ds it sounds like a little grinding noise every now and then I think it’s the left rear,it also rides like a little bumpy.any ideas ❤

48v club cart president runs great on low speed but when depress the pedal fully it stalls

48v club cart president runs great on low speed but when depress the pedal fully it stalls

good vid

My amp meter isn't moving but the charger still hums but when I meter the battery pack it's not charging. Not sure what to do

I’m totally inept at diagnosing what’s wrong with my PowerDrive 3 charger (same exact model as video). How do I know what part to replace?

Hi Wayne, I have a 95 DS and the yellow wire you were referring to, it’ll be extended (so it’ll be running from the solenoid to the main pack neg??) just clarifying. I already did the receptacle ground to the main pack neg and I deleted the gray wire with the yellow fuse thingy. Just clarifying that the yellow that’ll be cut will go from the solenoid to the main pack neg? Thanks in advance.

Where are you placing the leads?

Hey Wayne, Like your shows ! Have a problem 1996 Club Car removing Lead Acid 48 V batteries and going to Lithium 48V. It's installed and the computer is removed ! it has 6 wires= 2 Black,1 RED ,1 Yellow, 1Gray , and 1 Brown. Do I need to join 2 wires together ? the Computer is hard wired =NO QUICK DISCONNECT PLUG! RED goes to +of Solenoid [large post] , Yellow goes to Solenoid [Small post] , 1 black goes to Controller and the other goes to Charger plug,1 Gray goes to fuse at charger plug. Brown wire goes to front of cart maybe switch. Thanks in Advance!

OK, I had my charge three on my golf cart. 24 hours officially today and I can hear the batteries boiling but it’s not done yet. Still at 5 Amps unplugged it 2 batteries are at 10 V 4 at 9 V All we’re a little low on water yesterday before I started so top them off or raised them up using distilled water. Does it need to sit a while before you start charging them? If not, what would you check first to see why they’re not holding a charge?

Awesome set up! just curious,do you sell these carts,repair them or just deliver them to customers?

Thank you! Great video on changing out a speed sensor... should I replace the magnet as well?

wrong end. that's easy... need the one that goes on inside cart.. it gets loose.. heat ruins it.. that one is most likely bad too.

Thanks but? Why not show how to disassemble the unit instead of just jumping to the repair after you have disassembled the unit. Like how to get the big stuff out before replacing smaller thing. TY

Question for the teacher: I have an ezgo golf cart from 2010. When I try to move it, it sometimes takes 1 or 2 minutes to move. I just bought it. What could be the problem or is it normal?

are you still making videos? i need to lear how to do all the lubrication that is needed for a western golf and country 1999 mis green model.42 volt electric..hope you will show me how

Thank you for the information!

Thanks for the videos I have an idea for a video regarding mcors. Iv ordered 2 and I think they are bad, but I’m not sure. The ohms on one is 6.3-1.4K. The other was 6.6-.2k. From what I have heard if it reads over 6 your cart won’t work. A video of you testing/ troubleshooting the mcors would be nice. Thanks again!

Hello! What does jumping the 2 wire connector on MCOR do? I have a 2017 club car precedent with intermittent moving issues. It’ll work fine then stop working and work again. Saw other videos of bypassing the MCOR. Wondering if i can do that for a cheap fix.. just fixed a rattling loose brake pedal and a shorted horn. Thanks for the video and help !!!!!

Hi Wayne, I have a 2010 Precedent i2 that is not taking a charge. It has brand new batteries and the charger kicks on but it says it is charging at 0 amps. if you run the batteries down some same thing the charger kicks on but charger says 0amps. I have tried different chargers and still nothing. Could this be a bad OBC?

Thanks Wayne. What should I do if the last torque screw screw on the left of the pedal is all rusted and worn out? My drill bit ate all the teeth out.

Wayne, I have a 2005 club car precedent that continues to varie in speeds. Changed the moor and speed sensor. Any ideas?

Great video. Thank you for making it. It is extremely helpful. Only problem I am having is how did you mount the switch onto the dashboard? Does the switch come apart?

Did this on my ds and now it wont move at all. The solenoid doesn't click. I have the one thats like the precedent with the white and blue wires

Thank you so much on how to do this!!!!! I just got a 06 Club Car DS that wasn't running and after doing this we are roll'in!!!! Saved me some big bucks! thx again!!

Where is your positive and negative for the headlights

Thanks for explaining that OBC stands for On-Board Computer.

As a first time owner of a club car thanks for the video.

Great Video Wayne. Simple no BS help video. My Club car is running smooth through all speeds and it gave me 2 more mph. Thanks.

Old navy CTM2 here(ET2 ) and I like people that Know and don’t Guess!

Wayne--BIG thanks for this tutorial and for promptly shipping the potentiometer I ordered. It arrived this morning and in about twenty minutes my problem was solved. You saved me a ton of money and inconvenience! You have a new subscriber and I will be sharing information about you with my friends.😊

Thank you very much for this video which has been extremely useful, I ordered the parts and I have been able to repair my battery charger at low cost, fantastic.