Видео

i did that and now my engine is broken

Wait! What??? According to your demonstration it looked perfect, yet you said at the end that the propellor on this boat is "too deep". Are we talking millimetres here because as close as I could see, the bottom edge of the straightedge was exactly in line with the bottom of the transom? I'm trying to adjust the height of a Suzi 8hp 2stroke on a 12' tinny getting swamped by spray above 20kn.

I improved my outboard outlook with a small air cooled 4 cycle. The stern rides high and a little push does a lot. It starts easily and never has cooling problems. It rides too soft to slap.

Can I call you sometime and ask a question about my old Evinrude 1972 65 hp

Thanks for posting this video. Would lowering the engine help in reducing bow rise? I have a major issue with bow rise despite having followed the boat manufacturer’s recommendation with engine hp, weight and shaft length.

Thank you

Well explained. Thank you for sharing!

Hey Wally need a shave mate

On the vintage Honda marine fuel tanks there is a quick connect fitting that works like a light bulb. You push it in and turn. Do you have those fittings?

does #2 battery charge if running on #1 ?

Straight to point and no fluff. Thank you

Where can I get one?

Can this unit test an outbord motor with more than one spark plug? on the water?

is this same for the yamaha f25 the new one from 2017?

I replaced two prop shaft seals, after watching this video I now understand where my leak is coming from. My boat sits a lot. I may run some fuel cleaner down the carburetor to help clean things up.

I .have a 24ft cruiser with a pod .rolls to the right badly sometimes on take of . 200hp mercury .Cavitation plate has been set to the pod height which angles up and is higher than the bottom of hull would be about 100mm higher than bottom of boat. Would this cause this problem .Is fine once you get it on plane .Any thoughts on this welcome.

Thanks mate great info

Is it ok to run a outboard 20" on a 15" transom ???

Sir, how many inches will I give the transom height of the boat for better performance of this 75hp 2 stroke

Thank for sharing your knowledge. I always had a likeness for boat, I actually bought my first boat and your channel is a blessing. Thank you.

nicely done, thanks

can someone translate this to English please???

Hello, what if you have 3 cylinders? I'm running 1700 rpms at idle.. would I wrap it around each cylinder and adjust accordingly? TIA

Very well explained an simple thanks👍

As diagram shows 3batterys for the waterline duel battery switch

I don't understand wiring diagram what is the feed post for also you have 2 field tiny posts

Thank you for the info mate, in case I finished using the boat and prepare for packing it up,do you think its important to burn the rest of the fuel inside the carburetor as well? Or its not needed. Appreciate your help Cheers

well thank you very much sir

If those are the problems they shouldn't operate a boat this is stupid

Sorry bud can't hear you.

How do you adjust the rpm

Have a 6.6 gallon quicksilver poly tank. Bought new gasget for sending unit as it was leaking . Installed and still leaking from under gasget. Don't want to over tighten screws.

you forgot to mention the key cord emergency stop if beginners don't know about that and they don't have one the motor wont start!

So what propeller do you suggest for an 85 hp motor 16 footer boat?

Talk in inches....

Did you ruin the engine by demonstrating the bad position?

Thank you.

Thank you for straight easy talking and information 1/2 stickers don’t help much ✌️

Thank you sir 👍

Love how people don't read the instructions. Depending on how many raps made around the plug wire the rpms can change also not supposed to put a knot in it.

Just stumbled upon this coz my 95, evinrude 90hp has been a bastard to start and this should solve my problem, best short video ever. Will let you know how I go lol

Nice information Sir... it’s any matter if longshaft put on a boat instead gonna be short shaft...???? Any problem when it’s run..??? Safety question Sir... 👍👍... thank you very much

im just doing a refit, where can you find these stern brackets, new or used

when running your old out board motor should the gas cap vent be opened or closed

Thank you.... informative and helpful. Cheers..!

Great tip, thank you!

When comparing the height of the cav plate and keel, is it done with the motor trimmed all the way in or trimmed out?

Thank you wally short and informative just what I needed

I was waiting for the fly wheel to suck that wire up.

I sure appreciate the short a precise content. Please keep it up for new boaters like me. Can you please go over how the kill key works? Will an engine start without a kill key inserted? Thank you