- Видео 19
- Просмотров 5 401
Cliff's Cuts
США
Добавлен 30 окт 2022
Milling the canoe log!
I've always wanted to build a canoe, so when I saw all the Cedar logs I had, I knew this was the time to do it. I had to build a canoe. it's now or never! This was the first step milling the log to make the boards to then have them dried and then cut into stripes.
Thanks Dean!
This is the Kiln that dried my lumber it is located in Poulsbo WA Dean Lofall Owner - Sawyer NORTHWEST SAW
www.NWSawmill.com
Thanks Dean!
This is the Kiln that dried my lumber it is located in Poulsbo WA Dean Lofall Owner - Sawyer NORTHWEST SAW
www.NWSawmill.com
Просмотров: 1 004
Видео
Sliding greenhouse doors barn doors
Просмотров 6611 месяцев назад
Just showing off my thrifty homemade sliding doors for the greenhouse
Listen to it purr!!
Просмотров 107Год назад
listen to it purr!! started up my slabbing chainsaw on first pull after a year or more.
green house scaffolding build 2A
Просмотров 32Год назад
the greenhouse is slowly coming together as I mill some lumber for the scaffolding.
That's what I call a good day! Crabbing with the guys
Просмотров 1,1 тыс.Год назад
In this video I'm taking a break from milling and spending time with friends catching some crab on my friends' boat
The Cedar that wouldn't Slid
Просмотров 74Год назад
In this short vid Lou and I are trying to get a big cedar Log out if my stack of logs.
Milling 1 /2 the big Doug Fur
Просмотров 321Год назад
In this video I show a little of want it takes me to mill a big log on my sawmill and a little repainting of the mill after winter and lots of use. hope you enjoy!!
Changing the blade on my TMG-PSM26 sawmill!1
Просмотров 2,1 тыс.Год назад
This vid is of me changing the blade on my sawmill with a slight interruption because my Go Pros battery died.
Putting a Log on the sawmill 1
Просмотров 42Год назад
with the help of my friend Lou, we show you how I put a log from my stack of Logs onto the sawmill.
Mixing and pouring the concrete footings for the right side of the TMG greenhouse
Просмотров 38Год назад
The weather has finally warmed up and dried up enough to mix the concrete up and pour it in the holes for the greenhouse footings. I have had the forms in the ground for weeks waiting for the weather to change. all the wood you see and will see for the left side was milled with my TMG 26in bandsaw mill.
JUST A DRILLING !!!!
Просмотров 25Год назад
I am working on the beam that supports the green house drilling holes to mount the brackets that hold it up.
Making a card scrapper holder out of a figured piece of scrap wood
Просмотров 39Год назад
I needed a holder for my card scrapers, so I used a figured piece of scrap to make it. used a high gloss spray polyacrylic finish. I found out the lights in my small finishing space did not like the camera much. give me thumbs up if you like it.
Man, glitter cleanup!!
Просмотров 20Год назад
After I plained the 2x10s I found the dust collector full and had to clean it out.
plaining wood for the greenhouse Made with Clipchamp
Просмотров 31Год назад
I had cut some 2x10s from a Douglas fir log, but they turned out wavy! The blade guides on the sawmill were out of alignment making the wood wavy ! So, the 2x10s needed cleaned up with the plainer. It was nice to work in the warmth of the shop. especially when I had to turn the thickness plainer blades around.
New owner of this saw and it is of such poor quality that it is unusable Do not buy its is a waste of money and Customer service will not help
Sorry to hear you're not likening your sawmill; I've cut a lot of lumber with mine. I don't think mine is a wood miser by any means. what's the issue with yours?
WOW!
🛶🛶🛶🛶🛶🛶🛶
THUMBS DOWN! Where is the commentary like what was in your sawblade change
My commentary for this video ended up on the cutting room floor. To tell you the truth I was really getting into playing music, it was a new thing I was learning to edit in the video at the time. and the teaching and sharing took the cut. Thank you for pointing that out to me and I will do my best in the future to add more commentary in. Is there anything you would like to see done or learn about?
omg could have changed 4 times by now
How would you have changed the blade? I'm open to suggestions. what type of a mill do you have?
Good video. I have a 26" Bozeman from Princess Auto which is almost identical to the TMG. It does take longer to adjust things on these cheaper mills but not bad once you do it a few times. It really helps if the tracking is still good after installing a new blade. My yellow guard plugs up as well but I have been running without it.
@@cliffscuts5948 same as u same way without loosen guides 10 mins tops goes on to the same place old came off almost every time
I agree the tracking can take time when it's not good. I think I will try running without that yellow guard also thanks for the idea. I also think that changing the blade, and setting the guides is so important for the correct and continued operation of the saw, why rush it, take the time you need to double check everything is tight and spaced properly. thanks for the comment!@@leftyleeman
Seems like a lot of extra work and time to losen off the guides??
Your right about the extra time, but if I don't move the guides out of the way I can't make sure the tension of the blade is correct. The check for proper tension is moving the blade no more than 1/4 to 1/8 in with my finger. The guides are in the way. plus, the guides are important to get a straight cut, and worth the time it takes to get them set right. thanks for the feedback.
@cliffscuts5948 does it not have a set amount of turns on the tension handle or a torque spec? Once the guides are set so you have the proper clearance, you shouldn't have to touch them. I'm not familiar with that saw but, simply pushing down on the blade with your finger seems a little Mikey Mouse.
The manual for the machine called out the 1/4 to 1/8 deflection, a set number of turns or a torque spec would be a great quick check to get going milling, but the finger method is a pretty common thing, I've tightened many an alternator and fan belt that way on cars and other machinery. also, my grizzly band saw calls out the same method for its tension check of the metal blades. once the tension is set and I stop work I turn the tension hand bar two full turns to take tension off the blade. and when I start up days later, I turn it back two full turns. that is unless I get in a hurry and forget to tension the blade and start the engine. If that happens then I replace the blade because I messed it up. Thanks for the interest I hope I've answered your question and I'll try to get the question into my next video for everyone to learn from. Subscribe and like !! Cliff@@SteveBowers-h5p
Amazing trip guys! Outstanding haul of delicious dungees! 🦀
it was amazing and they where delicious. it was the first time in three years we got any Dungees!!!
CALAMARI! 😆
lol
Excellent video!
Thank you very much! glad you liked it.
A small planter!
how does 9" x15" sound 9 inches tall 15 inches long in a V with the ends acting as legs to keep the body for the ground for good drainage?
Yes please!
Looks like you’re all set up to make something super cool for me!
thanks Brenda Private what do you consider cool for you. it has to be fast so I can take it to you in pinedale!
A small planter!
Your Grandson… He bullies me.. makes me feel like I can’t live *sigh* he bullies me bc of my how big my nostrils are when he can’t be talking 😿 I can’t do this anymore so I thought I would leave this comment… nice sawmill
sorry Yas Rawr did you want me to talk to him, or is that just a good rap rime?
@cliffscuts5948 it’s just a good rap rime i don’t know your grandson
Im friends with your grandson
thanks for viewing tell me what you like and dont like.
Well all of it was good the only thing I would critique is when you finish the project show the result
@@DrS4lt i mwill keep that in mind some things take time to build what would you like to see built
❤❤❤
how you doing sis
@@cliffscuts5948 I am good!
Bro fr got the coolest sawmill ever 💪💪💪
thanks for the comment keep watching !
woahh
thanks for the comment keep watching !
My first you tube video!!!