Видео

Have i missed something? you have a relay to control a relay? why not just use the first relay on the switch?

Is that a deconstructed battery? I can't find any that fit that case without either building it DIY style or possibly removing the case off of say a redodo mini 100 ah. Could you give me more info?

what pelican case or type case is that?

Forever 😂 Nothing lasts forever.

Do you have to take the starlink out of the case or does it work thru the plastic lid? If it does, is the signal degraded at all?

Very cool, what case is that?

Good job, compact and simple.

Haha I saw your reddit post

Where did you get the mounting brackets for the Starlink?

Nice project. Any overheat problems with the Mini operating and the whole package in the sun?

Did you build it or buy it? If you built is, do you have a build video?

Neat. How do you power the starlink off 12V? Are you using a 12V to 48V boost converter or is this starlink 12V capable?

Very Cool! I was actually prototyping my own build with a custom built battery when I came across your video! some cool ideas very well built!

Doesn't the mini have a built in modem and router? The website makes it sound like a fairly all-in-one device

Looks pretty cool! Are you selling these?

7

I never noticed the facial hair on the bikini dancers 🤣

WE NEED AUSTIN POWERS 4 AND WE NEED IT NOWWWW

Why is this in my recommended. Not mad though😂

Replicating this because my Magnum AGS is a total POS

Can’t find one of these zss sensors anywhere, all the public files have been corrupted or deleted. Lost cause. Return of comma is imminent :,)

I’m considering returning it because it has some pretty bad ping-ponging. Did you ever notice any with yours?

Hello, can you sell ZSS to me?

Are there more than 1 relay output?

Is there an instructable or a guide for how you put this together?

cela fonctionne tu sur une prius prime tech 2017 ?

Wait a minute. What really happened?

What is this

It did not work well on mine. Probably because the lanes were not clear

Hello, it would be great if you could explain or point to some documentation where to configure which GPIO Pins are used by the generator setup. I see the cables, but not the SW configured. The rest is pretty clear and triggering a Relais with Venus OS is just what I am looking for. Many thx

Does it work on stop and go traffic?

I think a BlueTooth app would work if you have capability in your Pi.

Thanks for putting this info up. Over the years I have used gensets for portable work. Leaving the fuel valve turned on while unattended is risky, and not recommended by the manufacturer. The valve in the carburetor can leak, flood the engine, and in extreme situation the fuel will dilute the engine oil. Use a voltage controlled solenoid to eliminate that issue

Just started to get this vibration after crossing a cross road at high speed and the truck g’d out a bit, unloaded the suspension and came down hard on it. Suspect either the tires have moved off center on studs as I have stud not hub centric wheels, (methods) or the drive shaft got slightly bent, and is causing a harmonic vibration that seems to now be in the seats at around 70-75 mph. I hope it didn’t bend the output shaft of the transfer case or the front of the rear axle pinion shaft. I suspect it is a run out issue now, throwing an off center vibration into the mix. But need to check tires, then probably put up on jack stands and manual rotate the driveshaft as mounted and check with a mag-base and dial indicator for runout at the transfer case output area, pinion balancing weight, and then at front, center and rear of driveshaft. Run out is very critical as a slight amount will induce vibration. I worked in axle engineering at Chrysler’s jeep and truck division years back and we spent a ton of time trying to eliminate it in unit body Jeeps which proved very challenging. The pinion shaft is usually a big factor. Runout on it needs to be below .005-.007” any more and the vibration will be noticeable. And the drive lines need to be phased together correctly at the pinion to rear driveshaft interface.

Very interesting! How is the steering tourqe/rise time on the current official branches? Can a official branch make that route today?

have you got a link to the code you used for the Arduino?

where can i find your code for the arduino?

Can it do stop and go?

Nice video! Does it need extra hardware to do "stop and go"?

Looks good. I have a prius 2018. Does this make steering more precise?

I have the same problem , i just cant believe ford has so many problems and never do re-calls to all those problems. A truck cant just vibrate because thats how it was made is crazy. I pun new shocks, new tires, new rotors and took the driveshaft to get re balance. Still has a little bit of vibration. But o well is a ford.

I am currently building the same thing, thank you for the inspiration. The remote for my generator doesn't have a good diagram available online. Can you link me to the information you used on wiring the relay to the remote?

How do you know what the raspberry pi pin out is like im just trying to figure out did you program pin 40? Or is that stock venus os

Thank you for this video, it was well done and will help me troubleshoot my issues. I just want to make sure I understand your setup before I move forward. You just jacked up the rear tires, chocked the front tires, and then started "driving" your truck to test for these vibrations, correct? Just put it in drive and hit the gas? You don't need to worry about no resistance on the tires when it is up in the air like that? I want to make sure I am doing it safely. FYI, i have a 2WD F250. Thank you!

I have enjoyed your videos, explanations of how you stepped through these issues. Have you found an explanation, or discovered the VE.Direct pins on the Raspberry Pi’s GPIO? Thank you.

@Zorrobyte, I left a comment in your previous video about getting an update on the HTML5 touch screen based approach. I'm about to do the same thing. Would like to see your progress.

This is exactly my approach. I've got the raspberry pi running Venus OS installed with Multiplus 3000, SmartSolar 100/30 and BMV-712 connected. I need to get that display and I have a second Rpi ready to install the HTML5 app. @Zorrobyte can you provide an update on your progress.

You can run up to 6 relays now with the Venus software on the raspi. We have reconfigured the Venus relay control page to be on the front screen called switching .Also we have a interface done for this and to include I/O Analog inputs for temps and tanks Canbus VE direct etc. If any ones wants the information and schematics to how this is done the are open source just email me.