Видео

@@cesargonzalez6828 yes it is highly recommended, air pockets will form throughout the cooling system unless it is bled properly. It’s a fairly simple process that anyone can do from home!

@ can you share the link ?

@@cesargonzalez6828 For the aluminum flange here is the link, it’s also in the video description as well: thespeedcave.com/products/n5x-n2x-aluminum-coolant-hose-connector-mickey-mouse-flange And for the coolant any blue European vehicle coolant will work, we like to use Zerex G48 blue

The cylinder head on all of the motors this part fits on is aluminum, not magnesium. So it’s simply mating aluminum to aluminum.

@@shadow679king6 shouldn’t be melting unless it was either a cheap O ring or your engine may be running excessively hot. Best bet is clean off the mating surface where the o ring and new fitting sits as good as you can and reinstall a brand new kit. We now only use and recommend Uro Parts brand which is the one sold on our website, listed in the description

I bought the part off Uro I’m not sure why it melted the whole thing didn’t melt just a piece of the bottom part so u recommend I buy a new o ring or a new outlet flange ?

@@shadow679king6 Uro Tuning or Uro Parts? One is a website the other is a manufacturer

Mb I got it off ECS tuning. Is that company bad ?

@@shadow679king6 From one company to another I can’t really speak on their quality, but I will just say our Uro Parts brand flange kit that we have been using for years on our website is half the price of theirs and we have not had any issues. You did also mention that the bottom half was the only side that melted, this sounds a little bit more like a pinched O-ring during install rather than it actually melting. If an O-ring is pinched when installed and car runs, when the O-ring is removed, it will have a very visible flat spot which could be interpreted as having melted.

@@mikespeed3928 rear diffuser is a FancyWide E9x M3 diffuser, just slightly altered to fit 335i rear

@@SpeedCave thank you!

@@mikespeed3928 hardly any, but any time you have a straight pipe on these cars you will get some degree of rasp, it will vary depending on which downpipes you have too. However this system does a good job of mitigating it with the cross X section in the middle so even with full catless downpipes and no resonators it sounds miles better than any other straight through exhaust I’ve heard.

@@SpeedCave thank you soo much. I really do appreciate. How would you compare or rate this to the Turner Motorsports Valved exhaust? They have very similar and identical design and setup

@@mikespeed3928 The main thing about Turner’s valved exhausts that I don’t like is pneumatic valve control. This means an air compressor is running in your trunk which sometimes you can hear through the backseat but more importantly it takes a few seconds from the time you hit the button to actuate the valves open and closed. Bomiz is electronic which is immediate, and when you look at brand new cars from the last few years such as BMW for example, all of the factory installed valve systems are electronic, none are pneumatic for a reason.

@@mikespeed3928 Also if you decide to go with Bomiz send me a DM or email, the E9x 335i systems are on backorder but I can get you a discount for the wait.

@@SpeedCave I appreciate you. You're the real MVP 😎

Thank you! These are the 513M forged OEM wheels from the F80/F82

Its more reliable than you think Gallardo gen 2 and after are more reliable than most cars no common issues at all or problems, unlike the mental health of most people now in days😂

Its more likely to get impounded than broken

Good luck on the install! If you are interested the part is sold on our website as well, link in description

@@SpeedCave say it fits for 535xi well see

Should be $150 for the full license including both diagnostic and coding

Yes fits E92 just as well

@@SpeedCavethanks

Hello, this part does not apply to those engines as they use a different type of plastic hose fitting

@@SpeedCave Thank you for the feedback. Do you know whats the coolant hoses called that connects to plastic flange on N46 E90 as there's 2 pipes and mine seems to have some corrosion on the slimmer pipe since that flange connector has 2 outlets.

@@AvenNaidoo-qj4oh Yes that plastic flange should be BMW Part # 11 53 7 560 130 however please double check fitment to your exact vehicle as there may be different variants. This motor is not in the US so my familiarity with them is very limited.

@@SpeedCave Awesome, thanks for trying to assist. Will double check here in SA.

That’s crazy

They are called long reach angled needle nose pliers, and thank you!

Yes of course, that’s the same brand I had on when I installed this exhaust!

Sometimes clients have provided their own flange from eBay or AutoZone/ Oreilly’s and I have had the most issues with the O-rings on these versions. Name brands although more expensive typically never have this issue.

Having the issue of it not going in all the way imma take it home and try freezing it

These ones are from KG Splitters on Instagram! Just uses self tapping screws to attach

Yessir it will fit assuming it’s 2006 or higher

Did you get it without taking fan off ? Maybe you chose to use a breaker bar ?

@ yes I didn’t need to take the fan off

Thank you!

Thanks for watching and glad to hear