Видео

Wow my truck looks good compared to your. Thanks for the video.

replaced that ho, but started leaking again a couple days after

I missed tge rc part in beginning, so I thought ah he's like a airplane towtruck guy ,who brings his boy with him to work,then I hear you were the pilot,and when you were describing the touch n goes in dark in a glider recounting your crash I was like omg hes crazy😅😂 feathered right full throttle I was edge my seat like and your ok ? Haha just great dad bein a great dad ,I feel bit silly for that😂

What a gangster 😎🤘

.....and that, my friends, is how it's done. Great video.

I just love how you say what color wires you're hooking up so everyone knows what to do. SMH did you sense my sarcasm? This is a terrible help video. 🤬

super realistic video, thank you. Most of these trucks look like this by now anyway

Yes they got one. U got pp cut it out yourself

Thank you

NO. You only needed to clean out the little hole near where the vapor leaves the cover. This system pulls in vapor (thick with oil) at the bigger round hole (square on the new cover - [3:13]) and draws it through the cavity formed between the actual valve cover and the thin plate under the valve cover (the plate which has the two aforementioned holes in it). As the vapor passes through this chamber it cools and the oil in the vapor condenses. The condensed oil then drips out the little hole before it leaves the valve cover. If the little hole is plugged the oil can only go onward to the intake manifold which leads to smoke. You didn't need crappy $44 valve covers, you needed to clean the little hole. I found this out while researching my problem. My problem was there is another hole which limits the amount of air pulled in by the intake just as it leaves the valve cover. This hole was plugged on mine (corrosion and sludge) which meant I had no air flow at all. This caused me to get oil leaks and it degraded my oil with combustion crap. The best solution I've found is get a 2003 valve cover which uses an actual REMOVEABLE PCV valve and remove the valve. Replace the valve with the new insert available that looks like a PCV valve but it actually has no ball in it, just a hole. Don't forget to clean the 2003's valve cover's little drain hole. Google this part number GM Genuine Parts 12567915 This is the thing that looks like a PCV valve, but isn't a valve; it's a metering device that looks like a PCV valve.

Ignore the trolls. If you're not too familiar with the 3D printing community, there are a lot of what are known as "Bambu Bros." They are insufferable and you never really get used to them. There aren't really too many Creality fans, but one of those wandered in as well looks like... Like you say, you're learning and you'll dial the settings in with experience. These printers are nice and super capable. I have two, one with the DIY enclosure and one bone stock, though I still put the drag chain on it, I suggest you make that one of your first prints, it will help in the long run even if you don't want to use the enclosure.

dude must be trolling...

Oops, then I am happy with my k1 max when I see your prints, I have it for 3 weeks now. its also plug and print but much better, if i see your prints i wouldn't recommend it. I paid 300 more but that is reflected in the quality.

The building has supports on it too. That's why there is no door or windows. If you peel them off I'm sure it will reveal a wonderful little surprise for you!

How much that gasket cost?

I love it!

Www.tssalez.com Take a look and see if you like our little store :)

Thanks for the video, it was a lot of help figuring out to unhook everything from the actuator when it is pretty tough to see.

Video not helpful. Did not clearly show hose going to pcv valve. Removed a lot of stuff but didn't show it. Didn't say what model or year had the pcv valve integrated into the cover or why. Sounded surprised about something every time he turned around. Not professional at all. Felt like I was watching an episode of "Bubba's Garage".

Maybe the rings.

Beautiful color

If it's about a Briggs and Stratton, what's all this boat engine and RC plane stuff?

Why wasn't Bill a part of this!?

I would switch your oil to the Valvoline Restore and Protect 5w-30. It’s guaranteed to remove 100% carbon buildup around the rings and all throughout the inside of your engine after 4 oil changes. It’s a lot better than any Dexos on the market and it’s cheaper.

Probly a broken governer

By now if it’s never been installed then it’s about time for a coil cleaning job what a dumb idea,that should be a recall

I ran that red wire into a fuse tapper put two 20s in it and im not getting nothing. It is plugged into auxiliary power

You’re correct. That model year they deleted the cabin air filter. However, there is a kit and instructions on where to add it back. You will have to cut open the area that you showed. And, then install the filter and close it up with the cover provided in the kit. We found out because everyone on the crew was trying to figure out why grass and pollen was blowing through the vents.

You got it!

great video bro helped out a lot. Was rolling at the humor parts lol nothing funnier than someone calling themselves a ding dong. subscribed.

Thank you. I tried this and it worked.

Jesus Christ you ran 30 psi through stock internals?! Did you ever have any metal shavings in your oil when you changed it?

Which color wire is the cigarette lighter wire

Excellent!

Looks like you went through the wheel well to get to cooler,,,right?

Did you connect the cigarette lighter wire (that goes into the AC control unit) to the ignition switch of the new harness?

Dude where can you get that transmission for 75? Are you thinking before Biden messed everything up? They tell me 1600 and if it doesn't work might have a replacement and no cash refunds

Great VIDEO clearly and throughly explained everything!! I took the part to the store with me and we immediately notice it was bigger and wouldn't fit. The one I needed was $210 more but it took 10 minutes to install. I love how you provided the sizes of the tools that were needed. $ STARS!!

Ya thanks for making these videos it helps to understand the engine removal

I didn’t know that yellow thing was adjustable. Good video

Thank you for making these videos about Mercruiser 3.0. I am working on one and these videos are giving me a confidence boost.

No one wants to here your storys!

I've got a 99 and I'd never sell it let alone give it away. Best truck ever made. Still has the original exhaust!

Weird they put Toyota on a hyster

What a cutie!🎉

Good for you buddy. Im happy for ya

Your kids children will own this one day. Great find!

you really make my day, i have similar problems i have been trying for days i just follow your simple method and it work fine thanks man. ❤❤❤

Hell yeah

The air filter is built in with the oil pan