![Randall Strickland](/img/default-banner.jpg)
- Видео 85
- Просмотров 678 440
Randall Strickland
Добавлен 16 ноя 2012
BLUE RIDGE MODEL A CLUB TOUR TO CRAIGY SPRINGS VA
TOURING THRU THE BLUE RIDGE MOUNTAINS
Просмотров: 593
Видео
MY FORTY YEAR OLD TROYBUILT GARDEN TILLER
Просмотров 2,3 тыс.2 месяца назад
SHOWING HOW MY GARDEN TILLER STILL WORKS
MODEL A FORD ZENITH STRIPPED OUT GAS LINE INLET CARB REPAIR
Просмотров 8823 месяца назад
REPAIRING INLET THREADS WITH HELI-COIL
THOMPSON CENTER REMOVING STUCK BROKEN Muzzleloader RAMROD,[ SO I WAS TOLD]
Просмотров 2293 месяца назад
Bought a Thompson Center with a broken ramrod stuck in bore
MODEL T TRIP TO WALNUT COVE NC
Просмотров 8353 месяца назад
DRIVING THE FORD MODEL T TO A MODEL A CLUB MEETING
MODEL A FORD NEW ENGINE COMPRESSION TEST
Просмотров 1,9 тыс.3 месяца назад
LET'S FIND OUT HOW MUCH A NEW ENGINE HAS HOT AND COLD1
ONLY ORIGINAL ONCE 1940 FORD
Просмотров 7483 месяца назад
ONE OF THE BEST ORIGINAL FORTY IHAVE EVER SEEN!
Model A OR T CRANK GEAR INSTALATION
Просмотров 1,3 тыс.3 месяца назад
USING HEAT TO INSTALL CRANK GEAR
CHARGING MODEL T FORD MAGNETO MAGNETS
Просмотров 2754 месяца назад
CHECKING HOW MANY VOLTS MAG IS PRODUCING
TWO GREAT BLUEGRASS PICKERS PLAY HOW GREAT THOU ART
Просмотров 2124 месяца назад
PLAYED BY JOSH PICKETT AND SPENCER STRICKLAND
!929 MODEL A PHAETON, ONLY ORIGINAL ONCE!
Просмотров 1,4 тыс.4 месяца назад
SHOWING A MARC OF ORIGINALITY WINNER
FARMALL 140 SEIZED LIFT CROSS SHAFT FIX
Просмотров 4784 месяца назад
GREASE FITTING WOULD NOT TAKE GREASE
MODEL A FORD PISTON PIN BUSHING REPLACE
Просмотров 4824 месяца назад
REPLACING BAD PISTON PIN BUSHING AND HONING NEW ONE ON A SUNNEN ROD HONE
MODEL A FORD ROADSTER WITH MILLER OVERHEAD RAD NECK REPAIR
Просмотров 9795 месяцев назад
MODEL A FORD ROADSTER WITH MILLER OVERHEAD RAD NECK REPAIR
MODEL A FORD FULL FLOW OIL FILTER INSTALL
Просмотров 4,3 тыс.5 месяцев назад
MODEL A FORD FULL FLOW OIL FILTER INSTALL
FORD STUCK DISTRIBUTION BRAKE VALVE RESET
Просмотров 3225 месяцев назад
FORD STUCK DISTRIBUTION BRAKE VALVE RESET
FIRST START UP 255 MERCURY AND DYNO PULLS
Просмотров 5315 месяцев назад
FIRST START UP 255 MERCURY AND DYNO PULLS
WAYNE HENDERSON D-45 AT STRICKLAND STRINGED INSTRUMENTS
Просмотров 5087 месяцев назад
WAYNE HENDERSON D-45 AT STRICKLAND STRINGED INSTRUMENTS
MODEL A FORD REAR AXLE HUB BEARING RACE INSTALL
Просмотров 2 тыс.7 месяцев назад
MODEL A FORD REAR AXLE HUB BEARING RACE INSTALL
CHEAP AND EXPENSIVE DIAL CALIPER COMPARISON AND A SHORT TOUR OF STRICKLAND STRING INSTRUMENTS
Просмотров 2908 месяцев назад
CHEAP AND EXPENSIVE DIAL CALIPER COMPARISON AND A SHORT TOUR OF STRICKLAND STRING INSTRUMENTS
FORD MODEL T TOUR IN THE SMOKEY MOUNTAINS
Просмотров 2,2 тыс.9 месяцев назад
FORD MODEL T TOUR IN THE SMOKEY MOUNTAINS
Model A Ford Cream Puff Needs T L C !
Просмотров 6 тыс.10 месяцев назад
Model A Ford Cream Puff Needs T L C !
EVER WONDER WHAT THE INSIDE OF YOUR FRIDG'S WATER FILTER LOOKS LIKE?
Просмотров 2,6 тыс.10 месяцев назад
EVER WONDER WHAT THE INSIDE OF YOUR FRIDG'S WATER FILTER LOOKS LIKE?
What Happens When You turn The Key To Start HOW MODEL A FORD STARTER BENDIX WORKS
Просмотров 1,3 тыс.10 месяцев назад
What Happens When You turn The Key To Start HOW MODEL A FORD STARTER BENDIX WORKS
MODEL A ZENITH CARB THROTLE SHAFT BUSHING
Просмотров 90310 месяцев назад
MODEL A ZENITH CARB THROTLE SHAFT BUSHING
I've seen several videos installing the Mitchell overdrive. When you remove the rear-end, that seems like the idéal time to remove and restire everything onthat rear axel. Your all over it! Ya got'r done.😊
What a great car! Just maintain the mechanical aspects. Repair as needed and keep the rest original. Enjoy the hell out of it!😊
Ok so you are removing shims and not adding. I’m so confused on this part of the engine .
@@darrinwi yes remove shims to make the bearings tighter,
I'm asking this question out of shear ignorance. After a block is no longer servicable, is it junk? Could it be used for anything, or is it dumpster bound? Thanks! Interesting video. 😊
scrap metal unless you want to sleeve it back to standard
Thanks glad it helped
Great video!!! Very helpful. I’ve searched high and low for information on how to replace the rear main seal only to find out that the Model A doesn’t even real rear main seal per se . Now I know what direction to go. 👍👍👍👍👍
This helped a lot thanks for making this
I hope their air bags are working, 'cause they're running pretty fast in those old lizzies. And I gotta say it: those are some real pretty legs on that fiddler!
Thanks a huge bunch my friend. I just went through the very same ordeal. I was stumped but your video pulled me out of it.👍👍👍
Where can I get a oil filter system for My 30 A.
most all the model a venders has them,I get mine from Synders
Outstanding musicianship. 👍
😛
I've listened to this several times.She has some very tasty bow work here that I've not heard before.This is just outstanding.
The person from the MS, are you from Nita Yuma?
Great video, you are a expert mechanic on the MODEL A FORD, I have a 1931 TUDOR, I have been trying to get it running, I have installed rebuild Zenith Carburetor, new points, condenser, plugs, set timing, I have fire from coil, points are firing, fresh gas, the car just won't start, it's turns over fine, it just like trying to start with switch off, I've owned this car for 19 years, it's only been a few months since it was running, any advice would be appreciated, also what are thoughts on Electronic Ignition on a MODEL A, enjoy all your videos, THANKS.
I’m not big on the electronic ignition, I still use points, if you pull coil wire out of dist. And spin it over do you have a blue spark?
I would also check the connection at the amp meter if they’re loose it will cause problems with starting
I would also disconnect gas line at carb and see if you have a full stream of gas flowing
And to eliminate a problem with carb squirt a little gas in the opening of carb and then try to start
@@randallstrickland8204 I will be working on it again this week, everything you mentioned I've done except for ammeter, good spark at coil and points, steady gas flow, I'll check the ammeter and let you know what I find, THANKS.
Hello there- Thank you for posting this, there aren’t many videos showing this process. Do you happen to know the part number on that reamer so I can better my search?
She's unique as it gets!❤ Naturally talented--
I got a book from the library titled - Eric Claptons guitar . It was a non fiction featuring Wayne Henderson during a build and commissioned guitar gift for Eric Clapton . It was more like a daily routine of Wayne's days while constructing a Dreadnought guitar for Clapton and then Wayne delivering it to Clapton. Interesting book . That was back about 2002 I believe.
Yes I have that book also my son was working with Gerald Anderson at that time learning to build and was there when book was being written
What a talent!
Impressive! These were sold mostly in Mexico. In person, I've only seen one in the US in my life. I actually never knew the engines were from Perkins. Yours looks to be in really nice condition. 👍
Who. Is. Driving, jed. And. Granny. Clampett?
Contact. Info. ?
May I add.............SHE.........is beautiful!!
I always wondered how that works, thank you!
I absolutely love it. 🥰
This is brilliant. I was looking at doing this on my TA14 but this looks much better. I have all the Kwik Way tools to do it. What is the part number of the shell end mill and do you use the same one for A and B? It looks like you had to modify it in the gap under the cap.
Loved that bird.
Bet that AC unit blows fuses trying to keep the temp down on the hot pickin’ and playing in the workshop! Fantastic!😊
I’m in love 🥰
Beautiful and talented - not you Wayne. Cheers from the Mississippi Delta
85-140 gear oil
What type of oil/weight did you use in the steering box?
👌👌😊
Awesome video! Thanks Randall.😊
Another great model a video, think a for keeping on
As a fellow Strickland, I enjoyed your video. If you hadn't identified the location, I could have believed it was here in North Alabama.
Beautiful view. and great tour
Thanks for taking us along for the ride!
Real nice pictures of the farmlands on your tour.
I love these type of events. Great footage 👍
My Dad has a 31 Model A Roadster. He drove that from Joliet Illinois to New York City in 1939 with my mother t see th Worlds Fair. Can you imagine 30 mph on Rt 30 all that way.
That super cool I'd like to have one
Where did all the classic cars come from?
i have the same troy in my barn , they were the best , much heavier than the other pony and newer types ..just a all around great tiller ...
Yes they are!
I have a Garden way pony, smaller tiller, maybe older, a bit finicky but it still tills. Oats and field peas are another good cover crop that can give ya a little nitrogen.
Man, we started the same thing 3 years ago. Compacted clay in an acre field. And you aint lying about how hard and how much time it takes. But we are doing it anyway. Your garden looks great! Clay is hard to work, but nothing better for retention of moisture and nutrients which are hard to come by sometimes. I dont think a soil test can say anything but you need nitrogen :)
yes we just have to keep feeding our soil,I forgot I"ve also planted soy beens to!
Marina and wayne just great job and loved your thunderbird, from daniel boone national forest cabin on the hill big howdy
Thank you. That thunderbird is Wayne’s
i had that bolt break off and got stuck in the flywheel what a mess i took the starter off and worked the flywheel with a crowbar until it popped up and i grabbed it I also pulled out another bolt as well and a lock washer with a magnet on the end of a coathanger through the starter hole got lucky i didnt have to remove the trans great video too
Yes they can be a bugger sometimes
Sir that's a nice tiller.Oldie and a goodie.Thanks for sharing.
Thank you glad you enjoyed
Looks great Randall! Do you silage tarp the garden between seasons to suppress weeds? Fellow farmer. Keep uploading👍🏽
Thank you. No but I planted rye and red clover and there was no room for weeds over the winter
Great garden! My 45 year old ServiceStar tiller just quit this year. Tines locked up but there may be a fix!
Hope it's not to bad to fix!