Видео

@@Sihotang-79 thank you 😉

@@MinhNguyen-wb9rx làm đúng như tôi , đúng lỏi ferrite lọc, thông số như đã hướng dẫn không bao giờ hư nhé

@@markyichen6195 250-300 turns, 0.5mm copper wire, use li-po battery or lead acid battery, 21 PVC pipe, length 2.7cm

@@markyichen6195 circuit diagram 04:46

​@@TNHcreative Thanks you for replying.. I am trying to build a similar cyclotron. But I am having trouble with the power supply, I am using two 18650 cells in parallel along with a voltage boost converter, getting around 20volts and 10Ampere but still the magnetic field around solenoid is very weak, I mistakenly used 1.2mm wire to make the coil with only 100 turns, thinking that lower resistance wire will allow more current so more emf..

​@@TNHcreative Why have you used capacitors in your setup..?

@@markyichen6195 You did it wrong, the booster circuit cannot be used because the instantaneous current is limited, I suggest 3 18650 batteries to produce about 12.6V, the capacitor in the circuit is to increase the ability to release energy instantly (in a very short time) for acceleration, my coil is designed with the above parameters will not overheat during operation but still enough to move the iron ball, you should pay attention to the sensor position too far from the coil will not have enough force. Good luck!😉

@@saanviii__739 ≈10mm

@@saanviii__739 it is called "PCB test board"

@@mr_biimusic6264 có cách điện nha bạn😉

@@TNHcreative2 con điện trở 10k vs 470r công suất nó bao nhiêu W vậy

@@mr_biimusic6264 470ohm(1W), 10k(1/4W)

@@jppmzsl thank you, i just have the hand drawing for my board, it is in the video if you need i will send it to you 😉. what is your gmail address?

@@TNHcreativethank you a lot

@@TNHcreative youtube doesn’t let me comment my email address, i will be trying to comment, so ignore comments that are senseless

@@TNHcreativejp.mendezsandoval

@@TNHcreativemendezsandoval

Cái này làm để bàn coi cho vui bạn😉

awesome 😇, that's what i was looking for 🎉🎉🎉

Great ☺👍

@@AnthonyJohnson-m4d I really don't understand what you mean 😅

@@Sihotang-79 Thank you very much ☺☺😊

@@wiwakepandey9136 Thank you for your comments to improve the product. 😇

@@TNHcreative will be waiting for the upgraded video of the table saw

@@ranjitbhatta1 8 मिमी आरा ब्लेड शाफ्ट, मैंने इसे नहीं खरीदा, मुझे वह स्टील बार मिला! यह पुराने पंखे का शाफ्ट है!

rod ka bare me nahi bol raha hu wo jisme blade fit huya hai black wala

Search on google : -Saw Blade Connecting Rod

​​@@ranjitbhatta1Amazon pe milta he jitni mm ka rod hai utni hi mm ka shank adapter search karo mil Jayega 5mm se 14mm tak

@@vimalv2045 PVC 60

great good luck! 😇

The machine runs fast, but when sawing it is very weak.

@@TNHcreative So if you attach a belt does it retain the speed ? Some energy loss will be there through the belt but one advantage is the " shaft of the motor won't get damaged ".

I have shown in the video, everything has its principle, why I use a small pulley in the motor and a larger pulley in the shaft. If you find your design better, please share with everyone. ☺

@@TNHcreative OK. Agreed.

Вы действительно понимаете мой контент? Пожалуйста, используйте свой мозг, чтобы прокомментировать!

@@TNHcreative чтоб такую срань смотреть, мозг как раз и не нужен, чтоб не задавать вопросы вроде:"а зачем мне делать циркулярку, когда у меня есть нормальная циркулярка?"

@@covyshka259 Отрегулируйте угол при резке

Bình thường mà bạn! 😅

50mm😅

thank you for comment😇

Thank you for watching the video😊, you can search with the phrase "Pulley GT2" online and buy it, all the materials I have are in the video, and the saw shaft is an 8mm steel bar.

Tegangan nominalnya 3,7v, saat terisi penuh menjadi 4,2v.🙂