Видео

Thanks for your feedback..you can find it as gearbox repair kit.

@krisfix1983 👍

Lifters tapping probably. You can find a solution for Lifters. Put that and drive the car for a few days .see if something is changing

Oh ya, it's a manual.

@@Rabarbersq Anytime mate

@@Rabarbersq thanks

@@userrefcd2432 hi mate.check the chain

I've done one few days ago with rattle noise and was the chain ..replaced and all good

@martvermeule the car from video had only 60k miles soo dosent matter mileage..if you hear noise rattle and is from chain I suggest you to replace it .otherwise will be to late for engine

@@krisfix1983 its not a rattle noise

@martvermeule what kind of noise ? Usually this engines have a small noise like a tapping

@@krisfix1983 I see a you tube about the rattle noise my engine don't make that noise the engine runs nice only it use oil about 1 liter at 3000-4000 km I buy the car by dealer and he say that is normal for this kine of motor my older car Renault 1,6. 16 v don't use oil and have 270000 km

@martvermeule is not normal like dealer says. Engine worn valve seals in time this happens can be lot of reasons .keep the service on time

@@martvermeule check the chain

@@krisfix1983 the chain is replace by 78000 km and mij car have now 169000 km

@ionuttoma8733 hi mate. Thanks for appreciate my work. If you have compression and there is no misfire should be only chain .if there is only chain rattle and nothing else yes is chain

@@krisfix1983 I didn't try to start the car, I just checked for errors and I have DF101. And the right patina or how to you say to this tensioner for chain, was broke. I will buy tomorrow a new chains kit and I will try to start the car. Thanks again

@ionuttoma8733 tensioner is the common problem on this not the chain itself..usually when chain snapped 1 or 2 teth engine is not running right . Will misfire and usually valves broken

@sporismiha hi. can be same problem hard to say ..check my others videos and see how lifters was checked to be sure

I'm having this problem right now, on first start up my engine sounds fine and healthy until it approaches operating temperature it starts ticking! @sporismiha did you solve this in your case and if so what was the problem in the end? Like I said, what you have described is exactly what's going on with my car! Hope to get a reply, fingers crossed 🤞

Something Around £400

@@adrianmitchell2635 you are welcome. Anytime

Hi .this noise can come for a few reasons. First check swirl flaps noise can be similar , second put some valve lifter solution and drive it for a while to see if something is changing. If nothing changes remove the lifters cover and see if are playing. Thanks

@@krisfix1983 Where do i poor that solution in to?

@@erdeijill8438 in oil

@@krisfix1983 great! Thank you! Will try it! Hopefully fixes the noise…

Common problem on this .

You welcome. Anytime

Hi mate. Any unusual noises like chain rattle?

@@krisfix1983 Thank you for reaching out Mate. There No unusual noise on the engine and also it doesn't take oil have no smoke but i think the first owners doesn't change oil regularly.

@@RafaTe-wn7sc drain the oil and replaced. Before put a new oil and filters flush the engine to remove oil residual..be Verry careful with this engines make the oil service on time. No more than 5k between oil service. This is my advice

@@krisfix1983 Thank you so much I really appreciate your effort to answer my questions I hope you will make a detailed video based on my question. Thank you again

Check the timing chain.

Swirl flaps, coil pack,or chain snapped

Check the compression as well

@krisfix1983 thanks is there any way for me to send u the vid?

@@itzsaif2575 send it on my email cristiandr04@gmail.com

Yes mate.i have a video when was checked ✔️.

Is a normal sound for 1.2 tce

Forgot to mention .there is one metal pipe wich have a bracket on turbo. Right side 8 ml size ..you welcome

@@krisfix1983I managed to take everything besides the front intercooler pipe, I can see there’s a clip there on the plastic, how do I take that one off as I don’t want to damage it?

@@R3VollveR the one on top the egine? Have 2 clips .with a screwdriver pull easily on both sides and you can take it out..don't take them off just pull like 1 cm and unclipp de hose

Thank you very much I managed to replace the turbo using your tutorial 👍

@@R3VollveR you welcome ( cu placere

Hi mate.i will do my best to make a video to explain you maybe tomorrow. You don't need to remove the engine .you need to remove the hose from air filter goes to turbo , wiring clip , the clamp holding the turbo to manifold wich have 10 mils size if I am not wrong..on turbo there are connected 3 metal pipes 2 on top wich have 2 bolts/each 13 size and 1 on bottom with 2, 8 size bolts wich are heavy to remove as no to much space .for me was easy to remove turbo as I had to remove the manifold ..sorry I hope you understand what I am explaining. After you remove all this be careful as looks like is welded is so hard to take it out from manifold ..a heater gun heat to manifold and after hit turbo easily to comes out

@@krisfix1983Are all bolts accessible from above or I need to get down under? Do you have a Facebook page to get in contact with you? Thanks 🙏

@@R3VollveR send me your number to.contact you. After you can delete the message

Dont get down under..all from top

You can see in video mate .not swirl flaps. Hydraulic lifters

@@krisfix1983 wheres the after video, you said you'll make an after video so we can see the difference.

Tell me!! i know how painful can be 🤣

Maybe new ones .not this one .this is vauxhall /opel Vivaro 2012

@krisfix6794 OK thanks I have this problem and mines a 2oo4 so I'm guessing it'll be ok

new blade old fob@toppertruhio

can you explain, my barrel just stopped turning today frost ?

@@radiorocksolidradiorocksol9112 your comment doesn't make sense

Thanks mate

Sorry for late reply..easy if you done this before. But you need to remove some parts

Hydraulic valve lifters mate this was the problem. There is a video posted with the problem..swirl flaps was removed and all checked

😅😅

Yes mate.brake fluid dot 4

@@krisfix1983 thanks

Water water 😂

Hi..add some hydraulic lifters solution and drive it .see of something is changing.

@@krisfix1983 Hydraulic Valve Lifter ?

@@isbath yes .if not working needs replacing

To late for this mate

It doesn’t at this stage I tried it in my Z10XEP noise only went once new tappets and chain installed

Unfortunately the customer decided to leave the car and buy another one ..sorry

No.after 2011 shape probably

Permanent

Find a fuse diagram for Mercedes vito and you can find the location

Hi mate...First remove top cover and move the lifters one by one and if you see play on them be sure the noise is coming from there..remove the cover , coil pack all bolts around and check .if everything is OK there and nothing is playing check the intake manifold swirl flaps. You can see a vacuum on right side with a pipe on it .that one adjust the swirl flaps in intake manifold. If the noise goes away problem is from there .please send me a video if is possible.noise can come from injectors as well if not to loud.

@@krisfix1983 Thanks, great advice. Will have a play and take it to the garage if I get stuck

I have same problem Corsa D 1.2

​@@paragoninternational7052 this is a common problem on this engines.1.3 diesel much better

No i think yours is normal they do click abit

Hi .really sorry but the customer didn't want to go further to be fixed. Soo no video

@@krisfix1983I have one fully broken and rocker hit into spark plug well, so got to repair hole and replace. I really need advise how to take out cam without taking entire chain off

@@DanSmith27 unfortunately you need to take the chain out to remove the camshafts. You need a blocking Timing tool find on ebay around £15 and you can remove the chain without problems

@@krisfix1983 ah I thought I could lock the sprockets at top and take the one cam out, it’s the exhaust side, that sucks!

Hi mate..passenger side under glove box left close to door ..pull it .most of them red colour