Видео

What’s the logic behind running it that rich? Seems like you’re giving up a fair bit of performance. Great video though. Been contemplating the conversion myself. I think I’m sold now.

Good video, the kit is a nice one stop option for this conversion but just so you know you can get the parts from your Stihl dealer by putting the bar from HT pole saws on there. Every schematic usually has two sprockets or more. Out of all of those usually there is one that is a different pitch chain. I highly recommend this kind of conversion not only for these in tree limbing saws but also for your ground guys for their rear handled saws. The chains are cheaper, faster to file, and less exhausting to use because you’re shaving off bar weight. It’s not as dramatic as issuing a light weight 26” bar are a larger CC saw but even on those smaller limbing saws we naturally tend to reach away from ourselves while limbing so it makes a difference. Think of it like holding a 5 gallon bucket full of water near your leg vs reaching out fully extended with that same full bucket. You will definitely feel it. Nice intro song and keeping the content relevant and not click bait. Stay safe and keep climbing!

Does this have steering stoppers? mine seems to turns very sharp and the fork ends up hititng the radiator or frame

I have the same engine. Just finally got oil leak fixed, valve cover. I believe my head gasket is leaking a little. Still runs good n mows. But leaks oil exhaust side of engine n smokes sporadically. Kinda black on engine where head gasket is. Is it still safe to mow grass with it. I do take multiple breaks to let it cool some. Thank you. Great videos.

Spray starting fluid around the crank bearings and intake boot to check for air leaks on that 372 clone you're having problems with. Id bet there's an air leak.

Owned mine for about a week ride it every night. Love it. One distinguishing key elements is the handlebar width which is 21 inches. Typically wider than most scooters I see including the segway. This adds more stability for the ride which is fantastic I actually like it's more than the Segway ninebot Max.. I find it more fun, and at 30 lb much easier to carry around I call it two thumbs up for Evita

What grit is that sand paper?

I got this same clone saw, ran alittle like ass until I tuned on it and now I swear the thing rips like nobody’s biz it’s freaking nuts I’m beyond impressed

Where can this kayak be purchased? Who sells this?

I would like to see advance vs retard on the dyno as I've always thought you would advance a saw unless really upping the compression/squish area/decreasing squish height. On removing the muffler tubes, be sure the bolts are tight cause they end up in the cylinder if they back out.

I would like to see some of your poulans on the dyno. I just ported first two saws, a 4218 strato crafstman.poulan and a 4620 pp non strato. The 4218 was 14 seconds in the cut stock, got it down to 7. The porting was the last thing I did it took me from 9 to 7. From 14 to 9 was a combination of muffler mod, drilling the carb venturi out from 9.5mm to 12mm, opening up the slot between the fan and air box, removing safety rakers and optimizing the chain, unshrouding the air filter and intake, shaving the carb blade screws and shafts, timing advance. If you are starting porting like me these saws are ideal. I way overshot mark on my 4620 went from 143 to 165 on the exhaust. Still dropped from 6 to 5 seconds after porting. It was already muffler modded and optimized without porting. I cant believe it got faster, thought was for sure going to fall on its face. Got a lot more to say but got to go right now. Needless to say very interested in seeing these saws on the dyno and how close you can get one to that 543xp clone. Cool channel!

You the man

You are a absolute fucking retard you are trying to help people and don’t even tell where to put the timing marks

What chain are you running on the 295?

What is the app called I threw away my manual

What is the app called I threw away my manual

What handle bars are you running bro??

Well done!

How do I get the clutch off beside flywheel it won’t slide off or anything

did the 2005 airbox good fit ? i just bought one cr 125 2000

How did it hold up?

Lmk lmk

I found a bike like this on offer up… dude wants 600 $ …. What are things I should look for or do you even recommend it it’s a 2003 ktm 50 senior

Is it possible to for you to share where you got the arduino board and where you got the software? I heard you say some things, but having a hard time Googling where to get the Arduino and software. Thanks in advance

Get rid of the hoodie neck draw strings. Cool vid

I have the exact same cheap Chinese one I actually bought it like 4 or 5 years ago and I just actually learned how to use it by watching your videos. Thanks for the help

I just got one. Opened the strato port. It sounds and runs very good but haven't cut any wood yet. For 129 dollars it was a ridiculous bargain i couldn't pass up. Fun stuff.

So you don’t tighten the rock arms and leave them loose?

If you have a 46cc poulan I would like to see how it compares to that nh843.

My Neotech 843 carb isn't quite right. I can't tune it to run clean at high rpms in the cut.

Hey man quick question when you put the centrifugal filter cover on do you need to put a gasket? I pulled mine off and it had a gasket on it that was pretty messed up. But I can't find the gasket online.

Does kit come with both head gaskets

What’s your idle screw and fuel screw settings ?

Thanks for showing your experiences so candidly. I am a new climber as well, and learn a ton from videos like this. Thanks for putting it out there. Godspeed.

How do you know how to put the camshaft back in what if you put it in wrong

Is the oil pump inside of the cases ?

Nothing holding those clutch parts on?

What's great is that's what my grand kids call me too. Pepa....

Im having a similar problem. In theory could i just put a stop leak in???

Nice review! What size elbow did you use?

Good video sir. I just finished this on a Kohler CV 730 mine was a little easier. I put the engine on a Murray 40 inch cut. Plus it has dual exhaust. I had a valve job on both heads since I had both off. Not a difficult job. The CV 730 has hydraulic lifters so no need to reset the rocker arms.

Would be interesting to see how the 750W version does.

Nice!🤘👍

This work will get into your blood and you wont wanna do anything else. Looks like youre doing things right and taking it slow. Be careful learn your species and how each reacts when cut.

Definitely recommend watching August hunicke

If you add a knee adcender you can basically walk up the rope won't be so hard on you

Why was the tip white? Was it normal?

You might want to look into the zig zag you bought. They have updated it because the first ones with swivel (I believe) had issues and one person broke and fell. So just look into that before trusting it fully. The zig zags are great.

What sandpaper grit do you use to slide the cylinder head on?

If I was on a tight budget and just getting started, I’d put my money into a zigzag too! 😂 Nice job, keep climbing brother.