Видео

Were they running it with the cab up lol I never seen such a mess

Thanks for the video!! Lot of help!

Can't seem to break the right side loose because of all the nuts on it. Any ideas?

Thanks! I have the same problem.

I am by no means an expert on Duo cone seals, but the Caterpillar ones I have done expressly state they must be dry. The only allowable lubricant to assist with installation is isopropyl alcohol, because it will evaporate and leave a perfectly dry surface with no residual contamination. The only place oil is required is on the metal faces of the sealing surface and they are very certain to point out not to get oil on any other surface while putting it on the faces. I have to imagine other manufacturers of equipment would be the same. I can’t see how a duo cone could work properly if its slippery. They rely on the tork from the oring rolling up the ramp. 🤷🏽

Way bigger than Festus's mule . Draft horse Donkey cross for Super mule ? Beauty

HOW MUCH ?

Nice

How does she work?

Take fine grit wet sand paper to the mating surface of the glass bowl that should help stop leaking

I have run john deere , champion, sany, cat graders but never before a komawtsu, never heard of them...i have heard of komatsu..ahhh the joys of woke english

Any ideas on getting the lines out, lines push all the way in but won’t release when pulled.

Do you have to lift the bucket before lifting the cab?

Good video. Any ideas on how to clean the radiators from inside out? No reverse fans on mine. Can you access radiators from belly pan below radiator compartment?

Mine keeps running after I turn it off and I can’t figure it out.

Just leave the hardware in the rocks for the next guy 😂

Caterpillar216B3 bobcat ac not working

They push as good as a D6

It goes bad because it doesn't have a filter between the diesel tank and the pump. It has one after the pump. So, if you put a filter between the tank and the pump, the pump doesn't break (it doesn't get dirty).

Do you have the part numbers for the kits?….Greaat video!

Nice Lathe!

Sir, this helped much to understand duocone seals in a practical way, thanks

Good grief…you ever heard of a pressure washer!?

How do you RECONNECT them though?

You need to learn how to make a video correctly buddy. You showed us nothing. Poor video

Wrap the hoses with that plastic spiral protector. Has made a great difference on mine.

Thanks for taking the time to show this repair!!

Thanks for taking the time to make and share this video

Nice bro

I was like dang this guy sounds like he’s from Utah - sure enough ha ha me too

this isn't a skid steer

Thast a rap!

I like and thank you, you are the man, great job

Thanks for the video, I am doing the same repair on my lathe but when I pulled the two halves apart the gear slid down and I don't know where neutral is. would you have a picture of what your neutral position is? Did you get it back up and running?

Was needing to replace the seals in mine and stumbled on this video while looking for another issue. Thank you for the well detailed visuals.

cannot be shot off when engine is hot why?

Update video did this work for you?

Good description

Why did you not put a diaper under this?

nylon gun cleaning brushes work great

Have you ever seen the case that sits on the 3 dowels crack? I have a machine with a cracked one, haven’t pulled it apart yet.

Sir please help,our cat 306.5 the travel is not working,left and right

❤❤❤❤❤

Thanks i have to reseal a cat skid 262d anytime soon

Hi there, I am a subscriber to your channel. A year or two back your did a video on your cat track loader. I’m having trouble with my cat 226b hand throttle. The throttle quit working the other day, and now I only have the foot throttle, which I do not like to use. Would you mind showing a novice like myself how to replace that hand throttle cable? There are no tutorials out there on how to do it.

680 case ck bake dis

Off on your pricing buy a lot

Can i do that on my hyper v too?

Nice job!

Just did one on a 314. Bit of a job for sure. Thanks