Видео

@@dhanyak.m9088 technically, if under stitch is a problem, it is usually top threading that is the problem...remove thread and rethread everythinh

@@dhanyak.m9088 pinne pressure foot should be up when you thread...

@@dhanyak.m9088 നാളെ വീഡിയോ ഇടാൻ try ചെയ്യാം

Glad it was helpful! Hope to add more videos soon

@@snehajabalachandran1771 മെഷീൻ തൊട്ട് ഇരിക്കണ്ണം. അവിടെ ഒരു ridge ഉണ്ട്.

@LittleEllysElizabeth അതല്ല doubt. Needle ന്റെ പരന്ന സൈഡ് പുറകോട്ടാണോ മുൻപിലേക്കാണോ ഫിറ്റ്‌ ചെയ്യുമ്പോൾ വരേണ്ടത്.

@snehajabalachandran1771 പുറകോട്ടു.

@@LittleEllysElizabeth OK. THANK U😊

Needle പ്ലേറ്റ് ടൈറ്റ് ആയിട്ടെ തയക്ക്...ചിലപ്പോൾ ബോബിൻ്റെ കേസ് screw loose ആയിരിക്കും

@@gafoorgp5055 checkthat it iss not in bobbin winding mode.

Yes, it is!

@@sonug9391 Thank you. I started in 2023

Singer 3321 is good, but I am not sure of 3505. But have heard it is good since it has a metal body. Kindly confirm

@@rajupradhan6475 I bought it for 1450/- inr from amazon

still good

@@LittleEllysElizabeth thank you

@@aysha.m.p4397 evide kudungi?

@@lakshmivp753 you're welcome

Happy to help :)

Of course

ruclips.net/video/Sgnh9BAYAMo/видео.htmlsi=Pl8a68LE94dhReUh Have made a small video. Hope you will find it useful

0-3months - 3.5" finished shoe size 3-6months - 3.75" 6-12 months - 4 1/8"

@@alpanaagarwal7289 sorry. I lost this plant when I didn't pay much attention to it. I used to get a few hours of afternoon sun.

Depends on price. Around 2000 INR on Amazon India. Check description or community posts for links

Hei. Thank you for the detailed comment

Thank you so much for this detailed trick for rotary blades 😊

Happy to help ..good to know that my amateur videos are helpful to few people

i would only recommend olfa/fiskars brand without checking.

Yes. but the stitches will be better if there is some stabilizer.

Hi...can you check my latest community post? The link is there.

Thank you❤

Adjust the tension and width....lower the tension..and use interfacing or stabilizers

@@LittleEllysElizabeth thank you sooo mush 😊. That really helped a lot

Thank you for your kind words. That frame is called Q-snap. I got this from America. I think the website called threadshop.in had these..but they are expensive.

Hei..thank you for taking time to leave a comment. I was also so scared to play with tension in my early days...and this was something I discovered accidentally...

Thank you

Thanks! Will do!

@@LittleEllysElizabeth doing great😀😃

Thank you

278 might be a good match

Also check 289

😀

ruclips.net/video/p-_C6s56bZs/видео.htmlsi=EkWs6S_I9az3uu2E

മലയാളത്തിലായിരുന്നെഗിൽ നല്ലതായിരുന്നു

Are you talking about zigzag stitch or doing pico for saree?

@@LittleEllysElizabeth zigzag for saree using this machine footer

Will try. Next week

amzn.to/3OaJ3ly

കട്ടർ മാത്രം പോര. മാറ്റും വാങ്ങിക്കണം

amzn.to/3UgcXIL

Let me give a try and get back to you

Hello again, After tested several thing. I found that the following worked for me : Using a thinner thread, and a sort of paper support that I ironed on the soft tissue (if the tissue is to soft), and the « A » foot, and I took (this time) a lot of care (when threading the upper thread) to guide the thread around the thread guide pulling the thread through the pre-tension spring. This is very important ! Attention that the thread go down in the gap between the two blade, which is the pre-tension spring. Before I did not put it correctly. And also, I noticed, the tension of the thread is important when winding the bobbin. I hold it slightly between my fingers and used I higher speed (between middle and low). And I checked carefully that there are a certain tension in the thread when pulling it. Both for the upper and lower thread. And also, for the lower thread, when inserting the bobbin, I noticed, another thing that is important, that is to make sure to hold gently with one finger on top of the bobbin when you draw the thread, following the arrow markings into the stitch plate thread guide from A to B and finally to C. (See Manual, page 9, to be found on internet, see internet site below). Then I tried different tension from zero to 7, and found out that, for me, tension 5 was the best option when sewing letters. And, finally it worked, I succeeded to write my name perfectly. I never thought that you had to be so precautious about the threading, the tension of the thread, the tissue support, and the type of foot. (The manual can be found here: www.bernette.com/en/models/bernette-sew-go-8, Or more precisely here : www.bernette.com/assets/uploads/general/Downloads/User-Manual/Sew-Go/EN/5029008.0.04-IM_sewgo-8H20HEN230630.pdf) //Fredrik

@@hansfredrikjohansson8742 Thank you. Have pinned your comment so that others can find it easily

I am not sure if you had a question...but thanks for the comment