Видео

amazing work bro, you should have shielded the guitar. just the aluminum pickguard aint gonna do much without shielding the pickups holes

I heard a rumor about a boy falling to his death in the ice plant. Any truth to this?

Hi whats the brand of the Pickups? Thanks

Is it fine if i remove the shorting bar and connect everything back together? Asking this because my safety switch does not work when the bar is installed,i assume the wedges on connectors are not lifting the bar up.

I just watched your whole build series!!! Very nice!!! Got some great ideas for the build I'm about to do, and confirmed some of the ideas I already had in my head!!!!!!!!! Good stuff!!!

Hey bro. How much youd say the engine weights?

Put new pups in while you’re at it.

Great Job, can i Send you now my TE62😊 Greetings from Sweden Michael

Market segmentation is total BS

Do a video on the fighting

Great set of three videos. Unfortunate that you were not successful. I have been asked to look after one of these. Hope it starts and works. If not I can learn much from your efforts.

Достойно уважения!

I think I would have lengthened the front out like a 4 :30 and then used a straight pipe or something to go through the hood and put a radiator on it off of a 430

Where did you get your service manual for the 393?

wait u didnt crown and level the new frets?

I was able to get mine to work by turning the ac to cold while the car is on. After I shut the car off, i removed the climate control fuse for 30 seconds, reinstalled it then started my car and the actuators recalibrated.

21:00 thanks for showing intonation tool for floydrose!

Nice job. I am surprised that you didn't think of upgrading the pickups as those were the other weak point on that guitar for me. I thought the fret work was ok personally. I did end up selling my Jem Jr as I could buy an RG550 for less than the cost of the Jem Jr and the parts for upgrading it.

Very well done, thorough and clear. I will disconnect because I mostly you the machine to do chores around the property. If mowing and I want to get off, I will shut it off. Thanks.

Ну хоть бы почистил бензопилу, а то все пишут все равно грязной будет. Нет не все равно, как попилил, почисти, так и прослужит дольше 👍👍👍

Do u not have any needle nosed pliers or what?? Lol

what mm drill u used for drilling guitar?

Did you have to chance the locking nut as well?

Very good job Very Informative!!! Thank You

I brought this October 2024 its a struggle to use with the batteries not lasting 5 minutes each

Fantastic video! For others not so skilled, I'd be concerned about using a crow bar and possibly elongating the insert holes in soft wood. Drop a screw in there or use a longer bolt with washers. I also wouldn't free hand the drill. That hole needs to be straight. You don't want to be leaning the drill left, right, or tilting front or back.

Quick question what size of drill bit did you use?

That's a lot of work and you must have felt like a million bucks when it moved for the first time!

That's an actually pretty good setup!

It's amazing how much you can learn from watching a video rather than simply listening to instructions without the visual. This is one of the best how to videos I have ever watched! I came away from it with the confidence that I could, in fact, troubleshoot this myself. It turns out that the electric was never getting to the solenoid because of the handbrake switch - the handbrake wasn't engaged (sheepish grin)! Thank you tightwadproductions!!

Красавчик

Great video. How did you resolve the loose bridge bushings?

I have a pretty severe side slope on my front lawn about 35° that runs parallel longways with the house..... If I pull that 4 prong bar and lean way off the side of the mower or walk next to it with the mower deck engaged would it still stay on? Thanks for your input

Dang! Can I send you my guitar neck for that amazing work?? I'm serious! Or can you recommend someone?

It’s a 300 not a 3000 😒 I’ll tell you just for one of these for free that hasn’t been ran in at least 6 years.. drained the fuel.. removed bar and chain cleaned it a little switched to on hit the primer 6x pulled the choke and fired up second hit.. I’m in total shock.. thought a full field system replacement was needed just to see it it works anymore. Echo def has my interest now after this experience.. prob gonna swap out the 14” bar for the smaller one though it’s not a lot of HP even for a 14” bar.. but low key might be the best unknown gem for regular around the home stuff..

Talk man

???????

Nice work, so the Gotoh fits right in without any modifications beside the wider insert for the trem posts?

a luking for store jn toronto for guitar harley brtnton mark

Fog light thing worked for me couldn't believe it! Thank you so much! I have been driving without AC for a month because I couldn't find time to mess with it lol.

what a cool place to visit and a really cool gentleman.

I wonder if this applies to a hybrid? Were gonna try it. The AC cuts out every once in awhile. Thank you for taking the time to post this video. Very helpful.

Nice work. Could you please discribe Every product you used to clean and derust everything? Thanks, Paul

Looks like your really enjoying that car. Very nice Model A!😊

One of the "must do'" with These Budget Jems for me Is I redo the neck in birchwood casey gunstock oil. Hate the way they feel and look stock. With the gunstock oil they feel a lot more expensive And in my opinion look better.

Good job

Got this one also re

Such a wonderful job!

Well, got in my car and no air. Worked the day before. Came in and watched your video. Went out and turned two clicks and wala, it worked. THANKS lol

Two-clicks worked for me, 2010 Fusion SE. Just stopped working a few days ago, glad I tuned in to this. Thanks also for the showing the HVAC scanning info.