Видео

The video starts at 12 minutes

Is it same method for cigarette lighter model?

That was excellent and exactly what I was looking for. I have now successfully set up and re-paired my TPMS. Thank you

How i do the relearn in the internal version? i have to deflate de tires? Thanks!

Good video. But what to do when the tyre temperature is wrong on all tyres ?

Very well explained...thankyou. Is there a way to 'delete' 2 of the Sensors. I am putting these on a Caravan and only want to see Sensors 0 and 1. I would rather have Sensors 2 & 3 completely blank rather than have them 'flashing'.

Excellent video!

Thank you.

Thanks so much for your tutorial. A great help. I do still have an issue with the display showing the wrong values. Especially the C,* temp. They vary sitting still from 7C to 27C . Its like it's stuck. Could the sensors be stuck,?

Hi I have MG ZS 1.3 turbo , now I have facing the problem for TPMS fault . How to reset this fault . In steering wheel which button for Reset ? Can u guide me to sort it out .

is it ok to leave this turned on

Hi, mine still blinks and does not pair (all four sensors), I think I will get new batteries for each sensor and try again

Front left sensor one not responding

Tried your tutorial but still same problem tpms is not pairing with the sensor. Also tried to check the batteries with voltmeter no problem all all are reading 3 volts. What seems to be the problem. Thanks

How to change the pressure value shown at the display

.

Very helpful video

I have the same brand but mine cannot be reset. It can't go thru those 7 menus. Is there any other way to reset it?

what is the trouble shooting for 3 sensors showing 0 psi and one showing the actual psi? are the batteries going low?

Hi. I lost a sensor, and got a replacement which i bought online. Is there a way to sync/pair the replacement sensor to the host?

This the the tut that i was looking for!!!! The rest of the vidoes on yt were just unnecessary crap!!! Many thanks mate..

Thanks for the video. In my case I have the small cigarette lighter reader plus 4 sensors. One of them needed to be replaced and I had a spare but only showing flashing 00

It wasn't cooperating with me when I got it in from shipment so i did a hard reset from the manual but it only made it worse. It's only picking up the front left and rear right. Hopefully your video saved would save me from running it over. Thanks bro .awesome on point tutorial!

AT LAST !!!! Seems like the only person in the whole world that knows exactly what setting 6 means!! Have searched EVERYWHERE to no avail until I found your video..well done sir and a thorough "walk thhrough" of how to pair them..A BIG THUMBS UP to you😊😊😊😊😊

Thanks this is a good video. However I had already installed the adaptors onto the tyre stems. Now they seem to be stuck... Also I can only pair two of the tyres I kind of wish I hadn't bothered if it was going to be this much trouble.

Sadly there is no way to properly calibrate this toys. I went to the gas station, filled all with same pressure and then all the sensors are giving me different readings.

Can we plug all the 4 sensors first on tyres, after that we do pairing one by one?

in menu no. 6, My device is showing all zeros at bottom, it doesn't even show pressure, what could be the issue?

2 of my sensor showing same identical identifier? What is wrong here. Im talking about the option 6 in the menu . Tire 1 and 3 has the same identical identifier.

THANK YOU DUDE...Your tutorial save my live, it works like a charm, after trow 3 of this ones on the trash, for dont know how to solve this problems! Thank you, thank you alot!!!

Hello, the measurements of these devices are generally different. Even if all conditions are equal and tire pressures are the same, it shows different pressure values on the screen. Is there a calibration or +/- correction factor for this?

My sensor is stuck at one reading, it charges and discharges fine but never resets properly, I tried resetting but it just doesn't change the set tire pressures at all, what to do?

He doesn't get to the title topic until the 9 minute mark. You're welcome.

Brilliant instructions for pairing your Tyre Pressure Monitoring System. 👏 👍

Does this unit turn on & off automatically? My manual stated it does but It doesn't.

My sensor doesn't have any numbers on it 😭 and it blinks those numbers as zero only

I have the same sensor but on a motor cycle so only 2 sensors and a small main display....the front sensor will not connect with the main unit.....the battery reads 3v on my battery tester.....any ideas guys.

Hi just wondering if there is a signal booster as I have a large caravan that they are fitted to and when monitor is in my jeep I donot get updated information?

Well done sir. But in my case i did everything right but after I put Battery into sensors and cover its cap then trying to fit in the valve but nothing happens at all. No pairing . What should I do?

It worked.. thanks a lot. Mine was blank for weeks now fixed thank brother ❤❤❤❤

You are amazing man, help me more than instruction menu of the product, I'm your fan

What to do if one readout malfunctions? My unit is only two months old, all was fine but now but the RF unit is not communicating. The readout shows 0.0. I have tried to reset to factory settings, removed and reinstalled the sensor unit, removed and tested the battery (it shows 3,2 V) but nothing works. Seems like it's not the sender, I changed the senders from LF to RF and vice versa, but the RF readout remains on 0.0.

Hello, thanks for the great video. Is there a way to set the low pressure alarm below 17 psi. I wanted to use this on a vehicle with tire pressures around 12-15 psi so the alarm constantly goes off.

Hi sir, why my RL the number still not chnage eventhough i alredy fill in with air

I have the 2wd version for elecric scooter, working ok but shows wrong pressure. When tires are inflated to 4bar it showing max 3.1 for front and 3.5 bar for rear tire. Is this possible to recalibrate? Maybe sensors are broken :/

What do you think is the matter when the RR pressure on the reader just isn't showing anymore? This is just after about 2 weeks of normal display. What should I do?

Good evening, the video is very good. Thank you for giving us your knowledge. a query, perform all the steps but the sensors do not send a signal to the screen, what could it be?

Muito obrigado! Apenas o seu vídeo forneceu as informações que eu precisava!!

If only I had seen this last year before mine got so lost in the programming that I chucked it in the garbage and got a different model. Book instructions were impossible to follow. Ugh.

this was a great explanation on how to use this. I am wondering if you can answer a question.. my unit instuctions says "pressure copes 14-87 PSI". I am wanting to use this for a small tent trailer single axle. (I don't find the range anywhere, however hoping this is possible..) I am about to purchase new tires but I have read that often max PSI for trailer tires is 85PSI (and I have seen at least one that was 90PSI). Does that mean that this unit will not go higher than 87PSI? Therefore it won't work for higher pressure rated tires? Also, when I try to program the low end of the PSI, the highest PSI I can put in is 35PSI which would seem not to help at all with the higher pressure tires. I don't know much at all about tires, but any help you could offer would be appreciated. Thank you for the excellent tutorial!