- Видео 49
- Просмотров 207 178
MattAnonymous
Добавлен 7 мар 2006
How to easily remove window glazing at home
I've struggled to remove window glazing safely until now. I wanted to pass along a technique that has made the process much easier. With just a simple garment steamer and a putty knife, the glazing practically falls off.
Leave the steam on an area until the glazing becomes soft enough for the putty knife to easily cut into it. Do your best to stay away from the glass. The real trick is only using the putty knife half way up the glazing.
Leave the steam on an area until the glazing becomes soft enough for the putty knife to easily cut into it. Do your best to stay away from the glass. The real trick is only using the putty knife half way up the glazing.
Просмотров: 3 816
Видео
Italians singing at Oktoberfest 2015 in Munich, Germany
Просмотров 5438 лет назад
Luca, his neck vein, and his buddy belt out some Italian tune.
Makerfarm i3v printing its own replacement parts
Просмотров 1109 лет назад
Printing in ABS first at 75 mm/s then 2x then 3x. The gunk on the bed is ABS I applied to solve adhesion issues.
Robert Plant & Band of Joy Misty Mountain Hop Bonnaroo 2011
Просмотров 9113 лет назад
Robert Plant & Band of Joy Misty Mountain Hop Bonnaroo 2011
Robert Plant & Band of Joy Gallows Pole Bonnaroo 2011
Просмотров 7913 лет назад
Robert Plant & Band of Joy Gallows Pole Bonnaroo 2011
Conan introducing The Dead Weather at Bonnaroo 2010
Просмотров 26414 лет назад
Conan introducing The Dead Weather at Bonnaroo 2010
Trombone Shorty and Orleans Ave Bonnaroo 2010
Просмотров 14014 лет назад
Trombone Shorty and Orleans Ave Bonnaroo 2010
Saturn SC2 front end noise. Wheel bearing? CV joint?
Просмотров 20 тыс.14 лет назад
Saturn SC2 front end noise. Wheel bearing? CV joint?
Playing with Google Voice and possibly the fabric of space and time.
Просмотров 63114 лет назад
Playing with Google Voice and possibly the fabric of space and time.
AdvMath program I'm writing for Livescribe Pulse
Просмотров 1,6 тыс.15 лет назад
AdvMath program I'm writing for Livescribe Pulse
New Orleans French Quarter dance moves that stop traffic
Просмотров 58615 лет назад
New Orleans French Quarter dance moves that stop traffic
L297/L298 Stepper Controller/Driver controlled by iduino
Просмотров 6 тыс.15 лет назад
L297/L298 Stepper Controller/Driver controlled by iduino
Nopi Drift Moroso 4/6/08 Orange s13.5
Просмотров 1,7 тыс.16 лет назад
Nopi Drift Moroso 4/6/08 Orange s13.5
Blud's formatting it 💀
Annihilating it lol, that drive is complete fucked now
What is the model number for the garment steamer? Thank you
OMG ty ty ty
Thank you for the video, this is a really difficult thing to do. So easy to break the glass or severely damage the soft timber frame. I have been putting it off for so long because of the thought of having to re glaze all my windows. I will give this a try :-)
Glad it helped! Good luck!
lol... whoops!
Fucking hell. I come looking for engine (lifter ticks) and find this. Thank fucking god mine is not making this noise.
So basically you have only two input pins connected to Arduino , one for the STEP and other for DIRECTION ? What about the clock pin and enable pin ? I was thinking to pull them up to VCC. What software, firmware are you using for your 3d printer ? Are you running your motors by sending Gcodes from a software like 'gcodesender'. Please let me know
Added it to the description.
can you share the circuit?
ok, my saturn is doing this. We've had to replace the passenger front end 3x. GET IT CHECKED by a mechanic u TRUST if you don't know for sure, especially if ur a lady, some mechanics WILL take advantage of ur $....DON'T drag ur feet, u will end up spending MORE $ if you wait.. do NOT replace bearings IF it's your cv axle, replace them AFTER the cv axle being they're no good, or u'll be buying them again, we did this and they went out in 1 day. Replaced: tie rod, hub, wheel bearings, now cv axle.
uh ya she's done bud, major blowby and a rod knock.
Warped rotors, my sc2 is doing it now because my cv boot rips and got grease on them.
hook up your pcv hose and it wont smoke like that or leak oil ...
Turn the engine off before you throw a rod through the crankcase!!!
yeahh ummm ur fucked
@mrstartup371 you mean LS1
the spider isnt eating the fly, its packing it up to eat later,
uh oh!
put a fart cannon on it and you wont hear it, or just go with open headers, exhausts are for pussies
have you blown the head gasket is that all that steam and fumes coming out?
the flux capacitor has blown!!!
Your sure is not a steam eng!???! LOL~
Sounds like the flux capacitor is loose. Should be able to get a replacement at autozone.
i have a 96 mazda protege and my car makes a sound like this but u cant really hear it tell 30 mph and up i was told cv shafft couse i knw i have one goin out and they said that it could make that noise also
Sounds nice ;)
Lol! One of my all time favorite videos on youtube!
RIP!
RIP little engine guy
lol who is the dumb shit who said its a Chrysler engine......LAWL go back and watch your honda videos!!!
@lordbemylight Wrong.
It's a Chrysler engine...not uncommon.
tick tick bang bang bang boom
@2000jeepsahara HAHA
How do you fix rod knock?
what time is it? rebuild time!
Definitely was the wheel bearing.
SINGLE SLAMMER... LITERATELY
GET THAT WOODPECKER OUT !!!! o.0
sounds terrible. make it go faster... lol lets see how much of that block we can destroy in under a second
Knock Knock! Who's there? Connecting rods, that's who!
@2000jeepsahara Fuckin love that! lmfao!
@2000jeepsahara haaahhaa nice one
whack a great big door knob on the the engine head, fire the beast up and you got yourself a remote knocking shed door.
Whos there? Heavens Door? thats a knocking shop or shed. Trade it in ,you can tell them its a knock off..
i think its a loose spark plug.... lol
@2000jeepsahara roflamo!!! where da hell you get that from hahha
Sounds like a diesel engine!
Should have just floored it till it locks or throws a rod..
wheel bearing man... better change it or you'll be doing the hub too.
should put a brick on the pedal and see how long it lasts!