Видео

Thanks. I’ll try tomorrow and let you know

Omg this was amazing it even in seized my caliper

Chalk gun 😭😭😭

U are amazing

My caliber is push all the way out would I be able to push it back in and just replace the brake pad ? At least for an temporary fix for a week

You’re a lifesaver because I’ve literally been working on my truck for three hours and the last thing I want is to have to take apart the brake line when I can easily press in the brake caliper piston. Cool trick.

What a load of bullshit,most cars today is screw back only.that gun wouldnt do the job

Such a ingenuos idea sir, thanks for sharing.

My piston compressor costs the same as your caulk gun.

Wasn't very tight, needs to be square or could damage the seal.Mostly stuck with rust and can be extremely tight.A method I have when aclamp will not dislodge the piston is to insert solid material A little less in thickness than the pads or the pads and the disc and gently push the foot break,the hydraulic action will work,once released a little the rust breaks and with a little perseverance the piston will go back.This is only a temporary fix,must be dismantled and cleaned up and repaired.Has worked for me.Charlie Aus

Tangalin lang yung bleeder para walang pressure kapag tinulak ang piston

Not the greatest, but it works. Use what you have. Great thinking. Love it

I usually use a C clamp but this is a great tip. Thanks.

C-clamp is what I use,, works great,,,🗜️👍👌💪🤠

You may end up w air in your lines holding that caliper upside-down

Jesus just use a pry bar and wedge it between piston a calipers I swear people make dumb things dumber

I'll be dam good job

Use a old big screwdriver & pry on old pads, Simple. C Clamp. Countless better ways.

C clamp and old brake pad

Chalk?

Great idea. I'm going to try it instead of my C clamp I normally use. Thanks for sharing.

Easiest way to get piston back in is use a c clamp.

Why lol , just get new calipers, remans, that caliper look bad dude .

... Abs?.

I consider that a bad tip ! If the piston is that stiff that you can't press it in by hand then it needs a refurb. You'll notice how easy a new caliper is by comparison. A stiff piston is going to give you a binding brake sooner or later. The atmosphere side of the cylinder wall will have a corrosion ring which simply needs to be sanded off. Add fresh silicone grease, all will be good as new again.

C- Clamp. So MUCH BETTER

Use a large C clamp

I just use the c clamp to compress it while the old pads are still on.

I just use a C clamp and one of the old brake pads.

I can almost feel and hear my knuckles cracking as I think of attempting that. I'll stick with the inclined plane on my c-clamps but if someone steals them, I'll caulk my calipers into submission. 😂

I can't take this seriously when the dude is calling it a chalk gun and not a caulk gun.

That's a great idea

I take the top off the master cylinder then a 2by4 with a c-clamp,works like a dream

That caliper needs to be replaced. Rusty piston will cause issues

Great idea the only thing is open the bleeder on the caliper that way your not pushing any bad fluid in to the master cylinder. Also the caliper will go back in easier.

Not if it has to be spun

Pushed worn dirty brake fluid back into the system.....the ABS control module and back into the master cylinder!

C clamp and 1 of the old brake pads

This entire video hurts my brain. Ugh. .. chalk?

I use a C clamp I think it's the easiest

Wow that’s a great idea thanks 👍🏼👍🏼👍🏼👍🏼👍🏼

I'm questioning if a caulk gun is strong enough. A 4" C clamp works well for me

It's a CAULK GUN NOT A CHALK GUN🙄

Block of wood + G clamp

Maybe I did something wrong.., cause now my caulking gun is 2" shorter, and the caliper is still stuck....

Bullshit

I've NEVER thought of using a caulk gun to retract a brake piston! That is a great one to add to the shade tree mechanic's tool box 👍

The Big cylinder next to that bearing is clutch pack. Replaced that along with all the bearings and off you go . There is some clearance to oay attention to .

Diabetes

From where? Looks so yummy, I HAVE to take my kiddo’s there sometime.