Видео

I made my own blast gates. 1/4” tempered Masonite as the slide, as well as the filler around the pipe opening. Used a 2 x 6 and cut an angled opening at pipe O. D. then glued the angled cut back together. The angled cut gives more glue surface. Then carefully glued the 2 x 6 to the filler, one on both sides. The filler is made with the 1/4” tempered Masonite of 3 layers. Top and bottom piece is 5” square with 4” opening cut in middle. Then for center, a 4 1/2” x 6”. This is the slide. It’s made, sized to cover the O. D. Of the pipe. The 6” dimension is so you can grab slide to open and close. I also drilled a finger hole for easier grabbing. Then just fill in around the slide to complete the blast gate and glue everything in place, except for the slide😂.

Three years on from the making of this video and it still is the most detailed on the effects of doing these mods and where the likely ceiling is on ROI. Thank you!

9:58 your like me, get to caught up in looking at the tools or project I forget what to tell the camera. I also just keep talking and leave it in the script 😂. Nice shop, I love getting ideas for my distant future shop build.

Thanks. Something i can listen to vs reading. Helps out alot. Will you be covering all Procedures of ASTM level 1 testing?

i bought mine and having difficulty wiith the install.... haha, maybe i will use the templ1

Hi Matt, thank you for the video. The manufacturer states that the kit of 4 castors, can hold up to 920 lbs.; (I assume, 230lbs. each). My bench is about 330 lbs. When I engage one castor on one corner, about half of the bench's weight (165 lbs.), will be resting on that one castor, until I am able to engage the second castor. In your opinion, will that be too much temporary weight for the one castor? Thank you.

the green one is better and only a little more

So is the 880 lb. total based on dividing the 880 by 4? In other words, 220 per caster? Thanks

Mistakes were made you must be in my shop 😊

Blanks???

Well equipped playground! Love it

Where can I get instructions and template? Did not come in box when shipped. Company had been non responsive when requested. Steve

Nice shop! GO BUCKS!

Blanks!! Nice shop too!!

buy cheap buy twice---buy better buy once. USA MADE

Blanks.. Very nice shop!

I notice your Sawdust Nation flag on the wall!! Josh and Nap are the best!! Nick is now rocking with us at PwnCNC support!! Look forward to seeing your spindle setup!! #pwncnc

What is the amp draw on the motor? Is it above the listed on the motor?

Nice job. I'm looking to build a mezzanine level above a yet-to-be built finishing room and was going to do the stairs just like you did. Already got the winches. But you gave me some ideas and I like that you put a handrail on it. I might have to put my drinks fridge up higher like yours, too. I have three overhead doors and have not had any luck finding an insulation solution. In the winter, most heat loss is through the aluminum doors, per a thermal camera, they are glowing red/orange! Did you order the doors with the insulation already installed?

I just picked this stock system with Oneida separator up at estate sale for $100, only really using for a cnc right now but do have a small garage shop I see doing more to later. What was the Wynn filter you used and did it snap right in or are those clamps an additional cost

GREAT shop, you have a lot of real nice equipment

I have those dust collector components. I eliminated the fan discharge port first! And that 5" flex, and that separator. If you look at it, the flange is offering a 25 to 35 % restriction, the flex is restrictive big time and the "separator" is designed for 5". Even sized right, putting a separator in line, after a primary filter, is wasted space....

$179 now (may 2024) -- totally hoping they go back on sale so I can snag a couple!

Funny no one ever say size of build

Great shop

Everything is pretty cool except for that hat!

This should be awesome for my bass cab!

Nice. What size is the floor space?

Nice one bud!!!💯💯💯💪💪💪

6'' Main trunk line for your dust collection reduced to 4'' for you drops or is that 5''?

👍👍👍👍👍👍👍

Looks great!!

Wow what a great work space Matt! 😃

Sweet shop Matt.

Very nice shop Matt. Love that pencil dispenser. I’m going to have to get one.

I'll take some blanks, please.

Nice one bud, that sure has a lot of T-Nuts in that assembly!!😂😂💯💯💯

Cool. Like to see that it in action!

Nice one!

🦾🦾🦾🦾

I always imagine that in the factory where these precise and highly accurate , millimetre perfect , tools are manafactured ........that every now and again they have " dumb down day" where they manafacture a batch of imperial ones 😂 . Imagine an environment where precision is down to the thickness of a hair for millimetre perfection, but every now and again you are forced to manafacture a batch of tools where you use your shoes , or close one eye and stick your tongue out to do the measurement spacing , just to satisfy the imperial " ahhh it's close enough" market 😁

Good video but lose the loud music brother. It's annoying. Think, usually the woodworkers are not intro metal or heavy rock music :) Just do the process in silence . It is more enjoyable, etc. Just my opinion. Thank you.

We put this together and had issues with the drawer only pulling out halfway. Is there a trick to it?

You lost me bro Hopefully you’re belly doesn’t get caught in the table saw

Thanks for sharing the find...repeatability is a good thing...

Very well done I may use the same techniques thanks for all the measurements

What radius bit?

Very informative. Really digging that song you have going on in this clip too. Who is that? Thanks!

Excellent video, thanks for the clarity. I’m trying to brainstorm how to add further power. I’m wondering if I took a second regular two stage system and after disassembly, mounting, etc, then duct that system right into the existing ductwork and filter, would that increase the power substantially, decrease it, or I can’t guess what else. I would really appreciate if you could give me your thoughts on this (would work, won’t work, really stupid because xyz- that’s ludicrous, whatever). Thanks!