Mostly DIY
Mostly DIY
  • Видео 14
  • Просмотров 59 941
DIY Oil Catch Can for Toyota Starlet ep91 Glanza
I had a few universal oil catch cans before but, some ebay ones are non-functioning(no air oil separating elements inside). Then I decided to make one for my car, which is the best option, because I can customize its shape to my requirements. Please enjoy my video. Feel free to subscribe, like & share. Thank you!
Просмотров: 484

Видео

HONDA XR250 Restoration19:13HONDA XR250 Restoration
HONDA XR250 Restoration
Просмотров 3,2 тыс.Год назад
This is a short video of my 2004 Honda XR250 bike restoration. Bike was in very bad condition when I bought it. There were rust on it's frame and many parts needed attention and care. So I decided to fully dissassemble bike and make it look brand new again.
Classic Mini Cooper Mayfair edition0:58Classic Mini Cooper Mayfair edition
Classic Mini Cooper Mayfair edition
Просмотров 983Год назад
A short video after detailing my buddy's classic masterpeice. It's a 1998 mini cooper with 1.3L efi engine with automatic gearbox.
EP91 Glanza short clip0:07EP91 Glanza short clip
EP91 Glanza short clip
Просмотров 131Год назад
Two Glanza cars in a wedding parade.
Homemade Workbench2:17Homemade Workbench
Homemade Workbench
Просмотров 1112 года назад
This is the one i build for my home garage using basic tools such as arc welder,cutoff mechine,angle grinder,ect.this one may not be the best option for you but you can get an idea from what i did for my specific requrement.custom made tool cabinets,workbenches are comes in handy when your work space is limited and you need to utilize evey inch of it.i could not record a full in detail video be...
Toyota Starlet ep91 fuel pump replacement10:18Toyota Starlet ep91 fuel pump replacement
Toyota Starlet ep91 fuel pump replacement
Просмотров 5 тыс.3 года назад
This is a demostration video of how to change/remove toyota Starlet EP91car in-tank fuel pump and this process is almost similar to most of the Toyota petrol cars which are haveing in tank pumps.My purpose was to upgrade my excisting 190lph pump to a 255lph one.in that case i went for a used lancer evolution oem one to support my future fuel requirements.It's simple to do and only required few ...
Valve stem seal change without lifting cylinder head11:59Valve stem seal change without lifting cylinder head
Valve stem seal change without lifting cylinder head
Просмотров 9 тыс.3 года назад
i had bad leaking valve stem seals in my car and it was causing white smoke a lot.i thought without removing cylinder it's imposible to do.but after searching i found some people tried to do the job by inserting a rope into combustion chamber to keep valves remain closed but instead of inserting foreign objects to the combustion chamber i realised inserting compressed air is safe and practical....
Starlet Glanza turbo flutter dump1:35Starlet Glanza turbo flutter dump
Starlet Glanza turbo flutter dump
Просмотров 8 тыс.3 года назад
This is a very short clip of how my car runs after intalling my home made ram manifold which contains how my cars turbo spools,making flutter/stall noises,BOV dumping noises while driving...enjoy! specs:CT09 stock turbo running 0.8bar,4e-fte engine,custom made exhaust manifold,downpipe,full exhust,FMIC,intake,stock ecu/fuelling,lsd g.box,short shifter... please check my exhaust manifold build o...
PRC road trip 2021(non-official)5:15PRC road trip 2021(non-official)
PRC road trip 2021(non-official)
Просмотров 1273 года назад
Note:This isn't the official PRC(Pocket Rockets Club) official video of 2021 road trip!!This video is made by me for fun. Recording gear:Yi 4K action camera, Audio tracks in this video, LiQWYD - Sunny, Ascence - Konnichiwa [NCS Release], NEFFEX - Best of Me , bensound-creativeminds.
DIY Dirt Bike Stand5:41DIY Dirt Bike Stand
DIY Dirt Bike Stand
Просмотров 19 тыс.3 года назад
This is how i made a maintenance/parking stand for my Honda XR250 using junk car scissor jack.This can be used on any type of dirt bike for maintenance/parking purposes.using scissor type car jack is NOT the best idea because it can lift the bike but not stable due to it's mechanical play around hinges.that's why i had to fabricate two additional support square structures to make it super stead...
DIY TIG welding table10:35DIY TIG welding table
DIY TIG welding table
Просмотров 4524 года назад
Hi welcome to my channel! This video is about how i made a small welding table for my TIG and ARC welding requirements.Most of the structure parts were fabricated by using 1.5inch zinc coated square tubes.metal sheets are 2/8inch thick and used 12size welding rods all the time for arc welding.I'll be happy if you can get some kind of idea for your own welding table project from this.Thanks for ...
Bench bleeding brake master pump.2:59Bench bleeding brake master pump.
Bench bleeding brake master pump.
Просмотров 1934 года назад
This is a guidence video of how to bench bleed your brake master pump and this video demonstrates the way i did it.By following this method you can save most of the time that you are about to spend after replacing brake pump.The whole point of this process is to get ready your master pump unit air bubble free prior to install... Music tracks used, Song: Fredji - Happy Life (Vlog No Copyright Mu...
4E-FTE DIY ramhorn CT9 turbo manifold4:044E-FTE DIY ramhorn CT9 turbo manifold
4E-FTE DIY ramhorn CT9 turbo manifold
Просмотров 10 тыс.4 года назад
This is the very first exhaust manifold build by myself using few basic equipments and a Retop TIG200 eco welder.Note that i couldn't use inert gas back purging method which gives the best possible inner surface finsh because i dont't have additional inert gas supply equipments at the moment.I strongly recommend you to back purge while fabricating SS manifolds/tubing.that's one thing i learned ...

Комментарии