Видео

Good afternoon here in Malaysia sir. I have a V 200 year 2012 diesel turbo 2.0 Gw4d20 automatic at 1207200 km on the clock... Few months back hade difficult starting issues so went to the local work shop as was recommended to replace all 4 glow plugs and was replaced. After replacing them aslo same issue difficulty in starting long time to cranking in order to start but when engine is hot she starts up find.. Went home next morning wanted to start her up... Same thing long time cranking until battery gone weak so took my dad's car and tried to jump start but she didn't start only cranking. So I decided to get her towed to my friend's work shop about 2 hours from my house. Was recommended to clean fuel tank and replace all related fuel filters and was replaced. Was also recommended to replace all 4 injectors and high pressure fuel pump was also replaced.. Just took back my suv and she's not running smoothly. The work shop didn't programme all injectors as they didn't know how and they don't know how to do so sir. Do you have advice on how to programme it and how can then do it? Please advise me sir

That a fluke 87? 😅

Thanks ledgen

Hi Chris, I know this a old vid, but where are the glow plugs on the 2012 V200s

Greatwall V200 Crank no start. No common rail pipe pressure. Hi Chris,have you ever had the subject problem ?

ear splitting intro, then can't hear anything you are saying

Brilliant video. I had one bank not working, supply & fuses all in tack and no signs of burnt or blown components. Just went round and re-solder many joints. And fixed it. thks

How do I load software

Shared

My car had a new sensor put in but light is still on. any ideas

Hey mate i know its been a long time since posting this video, but ive bought a greatwall x200 4d20 tdi and most scanners i use get the codes but mostly say see service manual or take to dealer. do you know of any scanners which actually show the codes information.

If you removed the two dowel pins from the top of the apron first, you would find it a lot easier to drop the gearbox without levering it and straining everything.

Legend! I watched this video when I bought my 336 (second hand) Yesterday my drive pin failed too. Will swap it out this morning. Thanks for the video very helpful

Your awesome thank you for your knowledge

Use a small slide hammer to remove the alignment pins between the top bolts to make access easier. Also, remove the spring covers from the leadscrew, they're useless.

I need injectors in my own great wall. How has the injector you bought performed since being installed? Just curious before I purchase the same one.

Spent on battery 's charger's, to me , I said , wait for discount prices.

It goes to show that Hafco lathes are shit.

Abs fault 2011 v200 code ?

Friend - Congratulations on the video - My MAKITA DC18RA charger burst components and I don't know the code to buy - They are the IC PWM with 4 pins on one side and 3 pins on the other position IC-1 - And the other one is likely a transistor in position IC -4 which is close to the (smaller) TR2 transformer -------- IT WILL HELP A LOT TO KNOW THE CODES OF THESE TWO COMPONENTS SO THAT I CAN REPAIR THE CHARGER - I appreciate your attention - Thank you

What happens if you change injectors but don't program them in with computer ?

this is my problem on my jig saw when i bought it blade clamp can i buy one of those!

Dove vi trovate??

My makita charger shows healty batteries as faulty . What could be the reason for it ?

I have a 2021 Steed and am told diagnostics ONLY AVAIL AT GW DEALERS here in Australia

aloy 7075 ?

nice

Hello👋🙋‍♂️ there Amazing and very interesting projects Super like👌👌👌 Thanks for sharing👍 Do keep posting new ideas Warm regards and best👍💯 wishes✨✨✨ The UnknownManCub 👍😎👨‍🏭

Did you have to bleed to remove air out? We are in a weird situation. Only cleaned intake manifold and EGR. To remove intake we disconnected fuel line to injector rail. Put back everything as it was. Bleed the system and no start. Bleed the system many times including the procedure for Delphi injectors by disconnecting electric connection to injectors and imv/pump. No luck. When we use starter spray it starts. When I do activation test on injectors hear the sound and crank it then it starts for 1 second. Because injectors operated and dropped some fuel. I don't know what has gone wrong. Any idea? One more thing which is also weird. When we do injector activation using Autel scan tool- we activate #1, #1 operates. but when we acctivate #4- 2 operates same thing with remaining ones. 2-3 3-4 Connection are correct we can't interchange. We had not done injector coding. Infact without putting the scan tool car did not start. Is it necessary to remove return lines from injectors for bleeding?

Great work.I would of put a thicker plate on the base.

i need that clamp so badly

Hi will this works on the new GWM ? 2021+ thank you

Very interesting and explained in plain English. Thank you

Thank you, helpful explanation for my next project.

The D is for Deluxe It has the dro and a quick change tool post that the standard 336 doesn't..

Thanx for this video! It gave me a direction where to find the cold solder. I was able to fix my Makita twin charger.

Nice video but holy cow, turn down the volume on the intro, my ears are still ringing from that!!!

awesome very impressive idea.

Where did you find the obd socket, looked everywhere 😑

How to reset the immobilizer

Does that have dpf set up plus tpms as well and how much does this unit cost

Gday, im sure the wife will be happy with that fix, I know Brass is expensive but would look great, I’ve been thinking about a 3D printer for a while now, not sure if I can justify the cost for the amount I’d use it, still thinking there, awesome job mate and thanks for sharing, cheers

Neat little Machine, nice Job.

Gday, what a beautiful little engine, very similar to what we had a school in tech class, you did a beautiful job cleaning it up, bloody awesome mate, cheers

Thanks for making this video I really enjoyed watching 😁

Gday, congratulations, the engine run very nicely, all the work pays off when they run for the first time, I’m looking forward to seeing what you build next, Cheers

Wow

Gday, the engine is looking great, I had to make 2 bases for the Webster engines and the Cincinnati mill done a awesome job on the wood, I’m looking forward to seeing the next video mate, Cheers

Hi we had 2 bad injectors replaced them but now not getting any power to any any injectors so no start any ideas

Coming along nicely Mate :)