Видео

Please have somebody hold you camera of use tripod...I'm feeling sick

Thanks for your input, just starting now. Cheers

I did this too it was wasn’t bad actually quite nice actually. That front mount literally like done in 7 minutes not including lifting the car a joy to replace.

Hi. Is that a big "s" pipe at 15:36 underneath the new part replaced, a coolant pipe? It broke on my car while having the smaller coolant pipe replaced. It's pouring coolant out and kinda crumbled to pieces right at the engine block 😢

Some Bullsheet ! Damn unreal

13mm hex or 13 mm tex??

13mm hex or 13 mm tex??

So stupid making that hard

Thank you for the information. 👍

Thank you for the tutorial. Took me almost 3 hours with no power tools… it should not be this hard to replace spark plugs man🥲

This isn’t 1998: it maybe 2008

I've seen a few videos of this process now, and I'm amused at how many times the actual process of inserting the new fuel pump gets edited or cut all together like this one. Not once have I seen anybody suggest removing the fuel filter canister from the new unit until the bottom part of the assembly is down inside the hole. That makes the job much, much easier to do. The fuel filter then just pops right on once you have the bottom part of the assembly in. Without doing that, it wants to hit the sheet metal flange and makes insertion of the new pump very difficult.

Awesome video, my 2006 gtx 215 ride plate screw cracked.. need to replace ride plate. Im ready to follow your steps 😂😂. What did you use to scrape off old glue from bottom

Thank you so much, It was so helpful video. my Dad and I replaced 4-mount after we watched your video May the God bless you.

Damn .. the pitman arm removal is what I needed to see

Great video. I found my ride plate at Water Works plus pipes and rubber o rings. I also wanted to include I used a smaller copper pipe cutter (after removing the cutting wheel) to squeese the ring clamps. They are stout so I also used small channel locks to turn the wheel to compress the spring. Once you get them placed over the clamp and tighten by hand they stay in place.

I also have a system too lean at high load. I was beginning to think it was the oxygen sensors lol

I know this is a few years later, but what was the wire you had to reconnect? Thanks again this is a great video

oh man, i really don't want to flush the heater core, i have LPG conversion done and there's a lot of extra stuff running around that area which i don't want to touch. Would it still be considered a flush without doing it?

How long have you been a "mechanic"?

Hi! I have a 2014 hyundai elantra limited, but it is Korean built. Do you happen to know if the parts are interchangeable, or do I need one for a Korean built? The part has been harder to find. Thank you!

God Bless You, because You are very Skilled and shows that You have the Right and Appropiate Temper and attitude, I am Transmission Rebuilder and Used to be a Transmission Installer back in the Eighties for 15 years!

Awesome video dude !!! Thank you very much

Don't need to take pictures. Just watch the video. How about those injector clips. What a pain. Breath on this stuff and it cracks. Oh well. Almost there! I'm going to try and rebuild the fuel injectors.

I laughed because I came to look and see how to install that hose that you broke haha, I did it the exact same way with a tiny bit of pressure against it, my question is where does the other end connect inside the Fender well?

You are amazing! I have been suffering through working blind on my towncar suspension and now I finally have the info I need.

Combination Valve - Compatible with 2008-2014 Volkswagen GTI CBFA

What’s the market adjustment?

Does it matter witch one first???

Thank you for the step by step process. About to start replacing all the spark plugs

Superfine!

Ohhh Vegas!! About 3.5 hours away lol good to know 😄

What’s the part number for the air intake hose ?

I cannot believe what a chore it is just to change out the spark plugs. Shame on them.

do you know the part number for the hose that cracked? I can't seem to find it online.

ugh i need a 2020 Hyundai Elantra video!!!!! 😭😭😭😭😭😭

Excellent video! Thankyou!

直６のターボか・・・いいエンジン

LETS GOOOO

LETS GOOOOO

Just a quick note. My brackets are attached to break lines. Releasing the bracket from below will not allow you to remove the intake with brackets. It is a 14mm passenger side and a 12mm drivers side my middle one was not attached either. A ratcheted box end was my solution. Good luck it is a jobs but well worth it

thanks for sharing this hard to find info. Any details on a check-valve location?

thanks so much my friend you were very helpful

Thank you ! Big help

Must feel amazing. Good for you man :)

Jeeps are not reliable vehicles every mechanic ive ever asked said the same do not buy a jeep

A very niece video tutorial, even the mishaps and small errors help you to expect similar encounters or even improve if at all possible. I give this video a 10 of 10. Thank you bud!

You should be looking at fuel tank pressure pid, watch pressure on your autel, if your losing pressure so fast you hear a hiss you'll be able to identify that on scanner.. I would say you with the compressed air are absolutely stressing the system to potentially its limits. Good strategies with your soapy water.

AWESOME VIDEO! One question is how did you replace the seal? It looks like it's got some type of snap ring holding it in.

SO proud of you!