Видео

Thank you very much for providing such valuable course free on youtube.

Please your video says how to download proteus not the guide so please change your video topic.

How to configure ultrasonic sensor with renesas

How to program dataflash ?

Sir please reply

Sir please reply me

How to interfacing with rl78

Hello How to using Hal outputcomparedelayedcall back?? Thanks🎉🎉🎉

After Long back brother

Dear when one cannot buy hardware, how can buy Proteus simulation software as per my little knowledge it is very costly. Is proteus is free for students and hobbies. If yes share the link i will be thanks to you

could you please upload a full lecture about johnny five,i'm confused on setup of johnny five

ESP-12E is SOC

I2C ,SPI ARE ON BOARD COMMUNICATION METHODS.

Thankyou so much for this great and wonderful lectures. Hoping there might me any paid courses by you. If any please share. Explained very clearly. And we understood very well.

Tôi muốn read Code Flash renesas của Rl78 có được không

How to read the sensor using renesas controller cs+ ide using interrupt

thank you sir i understood now

Stellaries icd is not seen in option of debugger selector i did all the procedure include downloading driver and also add on. but yet it not seen if there is any one here faced same problem and know to solve it, it may be helpful.

i have a problem with debugger i can't get in my selection of debbugger tho i did all procedure

God on Earth

There is a corerction ...ADC timer interrupts are not considered as software interrupts they are hardware interrupts .system calls are only considered as software interrupts .

Thank you so much, I just completed the whole playlist. You are an amazing teacher.

Thank you so much, today i understood how to pass 4-bit data

instead arduino i use pic18f4550 .during this configuration i can receive data by uart from bluetooth and pc usb port but can not receive data from sim900 module

where is the link?

Good one

line 1: fatal error #1965: cannot open source file "TM4C123.h" , I have included the CMSIS headers from Github and using in CCS

Will this arrow pointers and SYSCTL works in Code Composer Studio ?

Very well explained. Thanks for your efforts to make such a knowledgeful video. God bless you sir. 🎉🎉

Thank you.

Sir can we convert decimal to hexadecimal by first decimal -> binary -> hexadecimal

Does CKE and CPHASE is same or different

Hi sir, I would like to know if I could get source code for my project?

Harmony 3 isnt compatible with MPLab X IDE, what other projects folder can I use does it make a difference? Can I use Application Project's Folder?

Sir I am facing to send a string in RL78\G14 Microcontroller, Please send any reference video or link.

i purchased iot course from your website but it is still locked

Did we need to download all 4 software? Please reply

Bhai course kaha se lu apka

Hello sir.....i know that this video was years ago and i just started following your videos. I am having a problem when I press debug, It goes to startup code and all step buttons are greyed or inactive and only an X red button is active. Could you extend any help?

Thank you, but. why is machine cycle equal to 4/20MHz ? where is 4 from ?

Hi bhai I need help, I m trying to connect my nodemcu to my computer but it doesn't connect to any of my port.

Can i use input? I haven't found it, please help

sir i dont have teva c series lunch pad and stm 32 nucleo how to learn this course

Sir I need your help sir I am purchasing NUCLEO-F446RE - STM32 Nucleo-64 STM32F446RE Development Board after purchasing how can I test whole board whether it is working completely or not sir . Please help me.

hello, sir i am having issue when i am trying to load this program in picsim lab..i have made the changes according to picsimlab but still getting no response when switch is pressed....

When I ran the simulation, both 7-segment LEDs ran at the same time. For example, 72 is 99 and 56 is 66.

Embedded linux videos podunga bro

1:37 OOuch!!! was unexpected 🤭🤣

10/10 explanation ❤❤❤ Really u made my day cheerful. Plz keep it up explaining each and single topic in details like this one. Now i am liking, commenting. And subscribing 🎉

Hello I want your help, Recently I have purchase "STM32F411 Discovery Board", I found that its driver is not visible on my neither Windows 11 laptop nor able to debug on MacOS (its prompting; NO ST-LINK DETECTED) after lots of research I'm thinking to try with "ST-LinkV2 dongle" but want to know does this ST-linkV2 can work to connect Window11 with STM32F411 DISC board??? because on website its given those ST-linkv2 software are for windows7/8/10. just wanted to become sure from an experienced person like you, before purchasing ST-linkv2..... Hoping for your response. thanks with regards