Видео

When cutting the cable housings, it gives a cleaner cut and make your life a lot easier to use a dremel with metal cutting wheel

do they have a model that would work for the 4070 ti super

19:06 You should have connected your fan to the motherboard or fan controller if you're doing this kind of mod. It will free up more power budget to feed your GPU core. Yours have a 320W max power limit. On all Nvidia cards, the power limit includes consumption from RGB and fans. By having the fans draw power from elsewhere, your GPU can clock higher since it is bouncing on/off the power limiter. The core demands more power, but it is power limited.

Thanks for the video. The music list is rather incomplete, I was only able to find one track which is a shame because I like most of the tracks you used. Are you able to make the list complete? Thanks in advance!

Did not fix the one end of one of the fan mounting spring thingies. It's not in the screw hole where it should be :P

why on earth should anyone run fan speed over 2000ish rpm ?

Nice video ! Keep doing 👌 i was buying the same but did you forget one copper ? Next to the other one like on the technical instruction from raijintek ? can i install it without problem ? Thank you for showing us

How thick did it end up to be? I so need this setup 😂

Will it work with the AMD RX 590?

know this is old but a Thermal Grizzly KryoSheet would be great on the gpu chip and you wouldn't need to replace it, tho it is conductive only down side so by careful if you do go with it.

hello! same exact card and I just ordered this cooler! wanted to know if you think it's needed to get something to keep down the copper heatsinks, or you had no issues with them thanks for the well made and informational video btw :D

You got a part number or link for the rockshox fork?

i doubt it would have any positive effect for my evga 3090ti ftw3 ultra, but i am sure there is something (outside of watercooling)

what crankpuller size did you use ?

what pedals do you have?

Interesting improvement. My Zotac 3080 heatsink seems pretty good though, I run 3 92x25mm noctuas on it and at 40% (~750rpm), they can keep it the core at 80°C while pulling 270W. (Probably ~60% for 330W.) So your stock cooler doing as high as 78°C with those insane 3500rpm fan speeds seems really bad? I don't remember but I think if I ran the stock zotac fans at 100%, the card would stay below 70°C 🤔

Really suck the HP 3080 card has a hard BIOS limit of 320W and minimum fan speed of 30%. Ironically undervolting gets you more power/frequency headroom. I own the card i deshrouded it and zip-tied noctua NF12s on it connected to the mobo and controlled by Fancontrol v144 in the OS and undervolted to 0.9V @1845mhz . It no longer sounds like a jet engine but still maxes out the noctuas at 1500rpm and can reach 84C. The default cooler is built on min-maxing off the fans aka minimum amount of cooler mass to maximum fan speed just to barely hold it in spec. The morpheus 8069 at 145€ could buy you a better cooled card. Its cool for tinkerers but the price to performance isn't really there.

I switched to the 8 speed 13 to 32t Freewheel instead. 32 is almost as good as the 34 and you get to keep your 28t, and dont have a huge gap between 1st and 2nd gear.

The temperature drop probably had more to do with the original thermal paste being dried out. However, looks like it'd be a worthwhile mod for the noise alone 👍

I have an XFX Merc 6800 XT. It's about 8 months old since I got it, but after seeing this video, you made me consider butchering the card and void the warranty for that nearly 20 degree reduction. Wow

Wish they made a 360 one that would slow down the fan by even more

i think the fans are in the wrong position. you put them to release air to inside the graphics card instead releasing the air to out side of the card

damn that was impressive

Tires , mega range..and a generic ebay hollow fat crank 2x and use 20 tooth small . Then this bike is 2x the bike

I was so excited when this finally dropped because my Gigabyte Gaming OC cooler is loud as hell and barely keeps my 3080 in the mid 70s in an air conditioned room, but 170$ for a heat sink!? Got damn that’s double the price of the old one!

to remove that stuff from vrams use a pencil eraser itll rub it off quite fast

Music too loud (imo 🤷🏼)

Maybe I should have gone this route, considerably cheaper than liquid cooling, although I went cheap as possible on this loop I have yet to build, waiting on pump reservoir, which for whatever reason hasn’t shipped after 6 days

hi my vantus 3080 noctua mod in game 70c chip 90c mem 1200rpm 320w, stok 68c chip 88c mem 1800 rpm 320w, 2800 rpm over curva sheit

2800rpm 120mm fan is super loud man.

I am thinking about doing the mod as well with my HP 3080ti. Right now i simply have 2 P12s strapped with zipties on the original cooler. I'd like to know if you tried to keep the original metal bracket or is it to thick to fit under the VRAM Cooler of the 8069?

Why did you need a adapter for the fans to install it on your GPU? isnt it a 4pin PWM anyway?

Will this work with 4090?

Can you turn the fans down to ~1000rpm and still play under 90c?

These forks have massive bushings failures and many people say that rebound adjustment almost not working at all. I was going to buy Giant Trance X with this fork, but when I googled all the info I realised that I will have to throw this fork in the thrash can immidiately after buying, so I chose Marzocchi Z2 which also has indistinct rebound adjustment, but at least no bushing problems (though they are very small compared to Fox 34). So both RS and Fox say you're too poor to give you a nice fork if you only have $500.

Video is much appreciated. I wanted to jerry rig a 8068 (10 series variant) on the 30 series a while back. A lot of custom work but appreciate the company offically releasing new one. Question, would you try Noctua A12x25 for accoustics and performance?

Hello, Im planning to do the same for my RTX 3080 SUPRIM X. Can you tell what is the thickness of the memory pads ? I want to put Gelid GP-Ultimate.

Great video. Just changed out my freewheel with the sunrace. Like the lower gear for climbing. Changed out the shifter as well and everything is dialed in for a 50# dolomite lol. Did you buy the Malus in black or did you have to paint it?

im using dell 3080, the stock cooler is fine until im running raytracing stuff. deshroud it with p12 max and the issue is solved. non raytracing temp is mid 60 while raytracing is low 70

Be careful when you buy this cooler i have it and use it on my amd rx 6800 xt and Cooler does not fit! I was forced to mod this cooler and cut off a bit of it. Left side of gpu die on this Cooler i was forced to cut off a bit.

Super nice demo vid. Thanks! And the numbers at the end!!!

I've just ordered one of these to replace the awful blower style cooler on my Gigabyte RTX3090. I've had to underclock it by 50% to keep the noise levels tolerable. I'm hoping that this will be a good solution. My case is windowless, to aesthetics don't matter at all to me. Going to have to choose fans and adapters though.

This is the weirdest and intriguing 3rd party cooler I've seen. It's neat to see a heatsink instead of watercooler setup though, especially because it seems to be pretty effective. Also I just want to say that when putting thermal paste on a gpu die, it is pretty important to get it all covered. Unlike a cpu with an IHS, the gpu die is just exposed so any spot that's not covered will get hotter. BUT yours seemed to spread evenly enough to keep it stable so good job!

Why would you dump money into a $500 bike? It is what it is. An inexpensive fat tire bike that works just fine.

Do you know the rear dropout of the malus? I have one I’m going to convert to a rear hub motor ebike. Everything I’ve read says 185mm or 190mm. I measured with the tire still on so I was kind of eye balling it but it looks more like 8” / 203mm to me if I’m measuring correctly.

Shoes by?

Nice video! Just recently bought an Axum as project bike and enjoying it so far. Was planning to pop open the BB to check the grease and bearings b/c I've heard a few horror stories of the condition from the factory. I used to tear down my old Rockhopper yearly, so my confidence was high. I decided to practice on an old Schwinn Ranger that we had that had never been torn down/rebuilt to try out some new tools. Took it apart with zero issues, shockingly. Confidence was still very high. Went to reassemble and the threads on the drive side were shot. No idea why. I never crossthreaded it and they were shot as hell. Now I'm second guessing my skills. :O I bought a threadless BB to rebuild the Ranger as a backup bike for my son. No way I'm paying to have a Ranger retapped.

Rule #1: Always remove the dork ring.

The Axum doesn't have a master link, you'll need a chain breaker.

Please tell me what size and what tool you used to pull the bottom bracket out please!