Видео

Do you sell repaired ones to worldwide ?

Well done

Great video,,

Good work!

Hi could you test the actuators off the Infiniti Q50/Q60 turbos?

what are temp you are using to desolder?

Hello sir I have same issue would appreciate if you could let me knw hw to change those led lights

Muchas gracias por el vídeo! Me ayudó mucho en resolver el problema!!

except your work bench all perfect

Just wanted to reach out and say a big thank-you for this great nugget. Normally, I would go to my trusty old mechanic. But he is away for a month and a half and I need the car to work this week for some trips I have to take. Sourced the part at Repco, same day I called them. But it is closer to $120 rather than online where you can apparently get after market ones for about 30 bucks. The reason I knew it was most likely the responder, rather than the alternator is because I literally had the RACV around changing the battery a fortnight ago and he tested the alternator. Time to buy a newer car.

Any chance anyone knows the diesel timing control resistor value on 1kz Auto 4 pin ecu?

This is all quite vague and putting a huge amount of solder melting hot air over all the electronics as well as joints. For many this is a journey to disaster. I thought repair was a matter of identity and rectification but times seem to have changed.

Could you tell me the pinouts to turn on the panel at the counter? Thank you!! 

Hello, 2013 hino195 P0045 turbo solenoid a circuit open ?

🇧🇷🇧🇷🇧🇷🇧🇷👏👏👏👏👏

I bet everyone’s got this tester in their garage. Not much use for a DIYer

What function does that mar1909pd component have to do with the injectors???

Hello friend, I have that same icu in a 2002 Citroën C5, the signal does not reach injector 2 and 3, it comes from the computer. You will know which component you have to change.

How can I contact you

This guy makes it look so easy but trust me when I say soldering is an art and it is extremely difficult on such tiny contacts. You can tell the way he gets it done takes years of practice

I have pin 89 negative trigger always open when I check it it contact to negative ecu body ground also the other pin what do you think

Where is the chip

Thats work must be done as by the boy in the video , this job cost me 250 euros...

my car wont crank or start...the cluster is blinking red light and it displays -------- dashes. here is the video ruclips.net/user/shortsETwl56QN0BE?si=9_zo3q4xTOCHubo7

What are you using to melt the solder ?

I've got one of these ECU's and my part number is becoming very hard to obtain a replacement for - I only just bought the car but there are two capacitors which have clearly leaked and the areas around the base of them are black.. is that generally a sign they're too far gone? I'm in Sydney but would be more than happy to send it across the drink

Hi ! You can sell my this chip ? I from Poland. On Ebay or smothing like that ?

What flux do you use?

Sir aapne fluks kon si company ka use Kiya jb hm IC ko soldering krte h to IC ki aaps me leg ek doosre se touch ho jati h

ONE OF THE WORST WAY TO SOLDER THIS KIND OF CHIP ( HEAT SINK PADDED) YOU RUINED THERMAL CONDUCTIVITY

Does the ic10 store the other options that usually change when you put a different Speedo in. Also, does the ic10 store the milage? Are they readily available as a chip? I usually swap just the LCD display module over from another odometer, but I've heard once the driver is faulty you need a new ic10, as you replaced here. Edit. Never mind, just read the number off the chip and can get one from chine for £8 posted. Thanks, you are a legend

What's the cost and business address to send the cluster.

pretty cool.nice work

Sept. 2023 watching this video. Hi. Where are you located? Do you still repair these ECUs? My XC Barina dies when warmed up. Cool the ECU and she starts again. Would it be a bad solder/bond, or an actual diode or similar problem. More to the point, would the fault be visible?

Hey guys can you fix faulty holden captiva ecu . traction control light and abs being told its in the ecu not the sensors?

what are signs when ☝️☝️☝️ goes bad !?;😢😢😢

To je divne pajeni,tenky hrot a pajet od cipu a hned je hezky zapajene a ne tak cik cak do krize a zas odsavat moc zbytecne zkratovani .😮

The problem is not on BGA CPU, the power chip next to CPU must be replaced...

Hi very professional work I really interested I appreciate if you could advice for electronic components vechile borad repair do you schematic diagrams for all type and brand Please advice how can get these files and data Thank you

hi boss.what the value of R558?

Cool. By the way, Bri'ish, a'n't yo?

Pro tip: if you dont remove the solder from the pin pads you can get the chip to just drop in place w/ the heat gun. 😜

Love it, all the cursing 😂, you sound like me 😂😂. Great video thanks for the info and the laugh x

Love the content mate 👍👌

can I pay you to do mine the same way

Lol. Bad idea leaving pressured heatsinks on board, should be stripped down fully. If solder liquifies umder any chip with weight on it. Solder will bridge.

Weldon job boss, plz how do I identify ic that control ignition coil on Mitsubishi lancer ECU 2010

I'm from south Africa. How can I get the turbo tester? Can I please have emails or their numbers please

We just use a camera to capture the layout when removing anything from a board?

X-ray ???