Видео

Steve, at 5:50, when you set up 3 curves each selected by one switch position, isn't it simpler (and same result) to have one curve and set input to "Switch A" in general (not a specific position of Switch A)? I have mine set up this way, and I don't see any difference in end result. I can edit the three points, and Switch A moves the output across those three points on one curve. Maybe there is some benefit to having 3 flap curves and using only 1 of the three points on each curve (as shown in the video), but if so I'm not understanding what that benefit is.

Hi Steve. I have no issue setting up flight modes 0,1 and 2. What I need is a "fourth" flight mode. I created FM4 in flight modes. I assigned a two-position switch to it. Then I went into my mixers, aileron and elevators. I made sure FM 4 was enabled. I also made sure in the "trims" menu that I have made sure independent trims is enabled on each flight control. What is not happening is that FM 4 is not enabled on the main screen. What steps have I missed? thanks

I look at it as your just flying to fast to deploy or be using flaps but that's just me .

Is this a "per model" change, or is it a global change throughout ALL existing models.

Hi Steve. The latest firmware and Lua scripts I installed will not perform a calibration.

Hi Steve. I'm unable to calibrate the gyro on the TD-SR18. The latest firmware update causes the calibration to fail. I am using the latest scripts as well.

Hi - good video, but I also have the problem someone had below where when I edit a flight mode, all I get presented with is 'Active condition', 'Fade in' and 'Fade out' options. I have set all of the trims to 'Independent trims per flight mode', but no trim setting options appear. I think I have the latest version of Ethos running, as this was installed by the supplier I bought my FrSKY X18 from. Anyone any ideas?

get to the point

Great video! Really helped get my x20s working properly! I have got a question about flight modes? Have got x20s and using tdsr10 receiver. I’m running stabilised modes on FM1/2 And flaperons and tailerons (takeoff and landing) using FM 3/4 This works well for separate trims. But when I select FM1 or 2(stability modes) it overrides the other modes for flaps ( flaperons/ tailerons) Would be nice to run stability Will using landing flaps! Any suggestions would be much appreciated! Cheers Richard 😎

Thanks for hints!!! Its helped a lot ))

All good information for BASIC mode stabilization setup thank you. Now where is the advanced stabilization course? 😁 The TDSR12 manual says download / install three LUA scripts to use in setting up stabilization then a couple of pages later says you need to use RBmixer and a computer to configure ADV stabilization feature. There is very little current documentation and no tutorials I can find on setting up / using advanced stabilization. I am working on a model that I want to add stabilization to the canards on Ch 6&7 but documentation seems to indicate that must be done in advanced mode, if it can be done at all. Can you please put an advanced stabilization tutorial on your to do list?

Simulator is broken

How do i get your shit videos to stop showing up on youtube

Is there a kind of "panic" mode for us newbs?

Just getting to setup flaps on Ethos for 1st time - tks! Hey, is this simulator available from the Ethos app on Mac?

I have no seen anyone talk about the sr recivers with gas or turbine plane. How good are the sr tabelizer? Has this proven. Please help to provide video.

Thanks Steve! Look forward to it. I’m coming from spektrum. I’m hoping frsky doesn’t turn into those folks at least on how they market their channels.

Hi Steve, many thanks for your interesting tutorial. I followed every steps with my X20S + Frsky telemetry and only date, time and transmitter voltage are recorded. Nothing from telemetry although I get all data on my transmitter when flying. Any clue what I'm doing wrong. Thanks

Is it a gyro...?😮

Sounds like "pins" in the on screen instructions means antenna

Is it possible to explain right from beginning to the end how to set up the Gyro on it TDTDSR receivers please I’ll be appreciate it

Hey Steve, can you do this Flap to Elevator setup in flight modes. Looking for a way to do 3 positions, off, takeoff, landing. Can this be done using a premix? How would flight modes do this common setup?

My x20s is on 1.3.3 and when I run update it does not update the radio, any ideas as I’m stuck on 1.3.3

Link to simulator in the description is broken 😞

This is awesome 👏🏾 I think maybe this can help me in separating the gyro levels based on axis(pitch, roll, yaw)? I’d like to use my archer SR10 Gyro with the gains on each axis on a switch especially during my first flights so I can fine tune my planes better. Is this possible with my setup? SR10 and S20s transmitter? I’m used to doing this on my spektrum radios

Thank a lot for sharing. Any idea if the new frsky RS would work with Futaba receivers. I understand I ll need a module for it to work with spektrum receivers. Thx

hello, i have put my gear on channel 5 and it works, but the aileron also affects it. how do i fix it? greatings Nikita

On mine I see "Missing Remote Version"..... X20Rs, Ethos ver 1.5.6

Howdy. Question: I have been able to get the stabilization working in a test plane of mine. But when I've put it in an F-16 EDF, after the Self Test, the plane won't respond to any inputs when the Stabilization is turned on in the transmitter. The plane works fine with it off. But when it's turned on, the plane's control surfaces are completely non-responsive. Any tips? The stabilization seemed to work ok before I self tested. But once I've self tested that receiver, the stabilization locks up the plane. thanks!

Your explanation was too confusing. It would be nice. Just show how to make simple Elron and rather mix.

stuck with frsky thru the turmoil because of the link, not sure now

Nice work Steve love the videos,and Iam always learning something from them that is very helpful so thanks heaps for you eforts

For an electric engine I would also set "Trigger Value" to +100 so the throttle cut always works regardless of the stick position.

Will the new X20 RS fit into the transmitter tray available for the X20 S?

hey Steve i have the archer sr6 receiver it is not in the for stabilized receiver what am I suppose to use for it.

Looks sweet! the link is dead, can you fix it please?

steve is there any way to tie the differentail value to say a trim switch or pot so you can adjust it on the fly and not have to go back and forth in to the mix screen so you can test it in flight and add or subtact the value

Steve you never disappoint. Thank You!

Can I ask what mW should I have my 900mhz antenna at 25mW or 100mW or more

Steve, I’ve been trying to figure this out for the past 2 days to setup the same thing on the same plane. I cannot for the life of me figure this out. I tried the same way you did and it won’t work. Doesn’t do anything. Right now if I don’t plug in the single wire it works in forward thrust just fine. When I plug in the reverse wire it stays in reverse and won’t go to forward no matter what I do. Please help

Steve, I am running Ethos 1.5.6 and set up my countdown timer as you suggested. However I am getting no audio call outs during the countdown. Has this feature been removed?

That looks like the dogs' bollox i cant wait to get my teeth into that watching the video that looks so similar to the flagship tx's of my old favorite Radio & i agree the stabilisation of the Frsky rx's without question fly on rails 👍 & its the 2.4 & 900 that was why i moved to frsky.

You’re guessing on the amount of flap comp,use flight mode, which are trimmable

I think using flight modes will be a lot easier. Flight modes will allow the trim to be remembered between each flap setting from there can be easily re-trimmed versus guessing on the amount of compensation by using a mix.

How do you copy a timer and paste it in another widget? My three timers show up in one model, but when creating another model, there isn't an option to create another timer with the second model. It's like they're only available on the first model. Also, the throttle trigger option is not available. I have updated to the most recent ethos. Radio is a Tandem X20. Thanks for any advice. I'm stumped. JW from K C.

The link to the simulator doesn't work, for me anyway. It goes to a Github attempt but won't let me in, error 404 etc. Is there a simple download for this simulator?

Hello all! I Need some help. Good flying buddy wanted update x20s to 1.5.4. went to ethos suite and now his radio want come out bootloader mode. He took his battery out of his x20s and re connected and it came back on in bootloader mode. Could he have bad SD card?

That ID registration is for when your rc toy crashes into a car

That was really helpful information, thanks Steve! 👌👏👏👏

Why does everyone take forever to get to the point this video should be 5 minutes max