Видео

Terrible fake video

Please answer I took the old one and a friend tried to start the engine without chain tension it just ticked not full start could it make problems?! And after changing the chain tensioner do I need to rotate the engine?!

What the reference of the resistance?

Can u guys believe i tried to do this at Home, and the screw did not come out? I sprayed with wd40 and the head of the screw is fucked now.. so no way is coming out now… ☠️ and i was doing it the right way

I have a P306A fault code. Is it possible that solenoid needs to be replaced?

Can’t find the protool app please help ?

The first version of this used to be serviceable with a rubber o ring and tabs to click into place, They switched to just welding into place to save money I guess during manufacture. Must have been cheaper to weld than a 3cent o ring. This method doesn't always work and you end up replacing the valve cover any way. Best to do it with valve cover off using a heat gun to gently break the weld, clean thoroughly and find an o ring that fits and reinstall new one as intended. I used to do this as a mail in service when valve covers were well over $1K but they have dropped so much its now affordable to replace entire assembly. Do this when you replace the valve cover gasket. Not a difficult job, average person can do it in a few hours with lots of preparation and watching how to vids before getting into it.

I just wanna ask a question about ds4? The engine light is on and gives an error on the screen P0016... Is this one the crank sensor on video should i change Or is there another sensor.. After change Motor engine Light will off Or not? Thanks for your answer and help from now

Grosse galère pour remplacer la batterie - un grand merci pour votre tuto

4 years later, this is suoer useful. Thank you

P0012 A Camshaft Position Timing Over-Retarded Bank 1 The fault sometimes comes on. This is helpful. The band screw on the back pipe faces backwards, making it difficult to access, 😢 but I'll give it a try.

Hahaha, how do you access the radiator?

Does anyone know the size of the oring? Mine is leaking oil and I'd like to buy the new oring prior to disassembling it...

Thanks for the vid. One reason I chose this car was because I thought it would be easy to get to everything. This is definitely unexpected!! Sheesh!

Cambiato batteria grazie a voi , in pochi minuti e senza fare danni. Video preziosissimo

Nice video. I just replaced mine. Unfortunately it still whistles at idle?😮

any change in sound after installing new one?

Can you pressure down this old timing chain tensioner onto a weighting machine. See how much down force it take to push down the plunger by 2 inch. 20 or 15 or 10lb of force? Then compare it to the new tensioner. BMW owners change their timing chain tensioner once every 60,000 miles. But never says any testing of old vs the new tensioner. Thanks

Hello, whats the recommended plus for the 5fv motor? NGK or Bosch?

Wow 😢 , my Nissan pulsed was the best take me no than 2 minutes to change it ‼️‼️

This is wrong procedure

another reason to change the entire rocker cover at 100k right?

Nice video! What were the exact symptoms of the problem before you decided to replace the CCV valve? Did it definitely get better after replaced it? I want to pinpoint the problem. have same engine

Citroen - 'Creative Technologie'...

What battery specification does the original car use?

Would it be ok if we didn't go through the diagnostic tool re-set?

Thank you very much for the video. It help a lot.

You really did a good job, personally I would go this route since I recently replaced valve cover gasket, not worth it removing vavlve cover again. Perfect fix and don't see anything wrong if done correct and clean. Good job.

Monse desconecta la batería

This video is the best thankyou so much I’m in Australia so not many people know anything at all about Peugeots and videos are very limited and after half and hour of searching it paid off

What software and ODM device do you use?

Hello sir, how many transmission filter on this car.? Why mine 2008 nissan teana j32 is only one filter.?

Great video,

Have any filter?

So can I go to the pick and pull and find a 328i and just yoink it’s fuel pump control module and replace mine with it and be done there? Or do I need to code it still?

On my 2011 Legacy, the usual 3 warning lights are on and the error code is for a glow plug. P1380 I can erase the code using my obdii reader and then I'm good for as many starts that day as I need so long as engine remains warm. If engine goes cold or I don't start car until next day, then the 3 orange lights come back on. Car has 275,000km on clock. I think glow plugs were changed before - not sure. If this were a glow plug issue then wouldn't the warning lights come on every time I start the car? The fuse linked to the glow plugs is fine. Might I have an electrical issue rather than a glow plug issue? The plugs probably do need changing but even the local dealer told me - if I can live with the warning lights then that's best. The car always starts fine even in the cold. DPF has been removed. Any advices / comments appreciated

Thank you

Can you make a video how to replace the headlight bulb, the xenarc ds1 35w on the ds5

Is there a simplier solution than using diagbox ,, are there any obd faultcode readers that can do this ?

Do you know by any chances the specs for the bolt oil level bolt? I was thinking in doing this and installing a magnetic one to catch eventual metal shaving debries that may accumulate over time

Really good

Is there no filter to change ?

Oil - rowe 9006 or ravenol atf-ws

Thank you so much for your video!

Many thanks also, its amazing how many ppl you have helped just by doing a simple video and deciding to share it with the world for that,, thank you. Will tackle this job in the next few weeks.

This was cringe!!!

Does the cap screw on the valve cover or does it just need to be pushed all the way down?

I just found some heated seats I want and I can’t get to the front bolts. Asked the guy up front and they indeed don’t have or want you bringing in a way to add power to the car. I have a Milwaukee m12 battery I will try tomorrow and see if this works. Thanks!!

Is the blower positioned the same on all cars? or is it in the passenger footwell on European models? also, when testing the blower at the contact while still in place, is it a simple two pronged plug to connect + with + and minus to an earthed point when testing straight off a12v battery? Many thanks for making the video 👍

Its not thp