Видео

Thanks very much. I went to Lexus and replaced the gas cap because it would not tighten as it should be. The dashboard lights issue was still there with the car. Then, I went to Volvoline to have my oil change. I asked the guys to disconnect the battery terminal for few seconds. It was frustrating, the VSC TRACK OFF LIGHT AND THE CHECK ENGINE LIGHT were still showing. Last thing I did, was to go to Lowe's and bought a wrench. I was determined, and prayed that God please help me to fix my car dashboard's X'mas lights. Then, with the help of Lowe's parking light in the midst of darkness-- this evening, I used the wrench to unscrew the negative side of the battery. Wow, it was a 1-2-3 experience: turned on the ignition. The dashboard warning lights for the VSC TRACK OFF AND THE CHECK ENGINE DISAPPEARED! Praise Lord Jesus; He saved me from the weight of tons of worry off my back.

Looks good

I love it. But, I could use a lip flange for breaking suspension bolts while grabbing the square nipple poking out the bolt with a pair of vice.

Dude I'm sorry this was not a good video

HOBO Freight names these tools Icon because they are conning broke dick Popeyes into buying them under the false guise that they are the same as Snap On, the truth is all the Icon tools are cheap poorly done imitations of Snap On tools and they are made out of soft steel. Two quotes come to mind that nail Icon tools 1. A fool and his money are soon parted 2. Quality is not cheap, cheap is not quality.

Nice job.

The reason is your air filter cap .after replacing air filter most of fitters doesnt click it propper way. So system suckd to much air and mixing wrong fuel and air mixture ,foults bank one or bank 2 catalitic converter below treshold and so on. So air filter lid must be tight ,and maf sensor ruber seal not stoned or cracked . Gvv

Even after removing the bolt and clip from underneath I still can’t seem too free the antenna. Any ideas?

BTW, using too much product makes removal a lot more difficult! She did 5+ passes for the exterior glass sealant, and it should take maybe 2. Plus she said it smelled bad, but if you only use a few drops it's fine.

I just did this job to my 2 month (literally 2 mon ordered from factory) with Adam's products. I thought I could get away with just glass cleaner, but for ultimate clean do glass cleaner, clay, polish, then sealant. The better you prep the surface the better the results, and Adam's applies and removes pretty easily.

you need to wash a dirty car. The car needs to have dried dirt on it to see if the product works or not. The snow foam was running white of the car.

Please tell me how do your front springs perfectly fit the spring perch?!? I thought the Koni yellows were made only for non-ST and the Swift Spec-R were intended for the ST? ST spring end should have a different angle than the base model at the perch and should lead to a slight mismatch if used together.

Awesomeness

Did you ever find good casters for what you wanted to do??????

Thanks for the video, I need this real quick on the go

On the bottle it doesn't say 20ml per liter in a foam canon. It's says 20ml in foam sprayer! That's a Manuel foam pump sprayer.

Where do you put the jack to hold the subfram???

Always wait until the ring bell stop before crank any vehicle

Let me give u one advice, and when you disconnect the battery in a vehicle to reset and connect it back u should wait until the the ring bell in the vehicle stop Ring,then u start the vehicle,that allows the computer to re-learn all the sensors in u vehicle,I have 27 ,ears of experience and is a common mistake that people do when start the car

All those tools & no cutting wheel...dont take you car there

Mine have issues with the brake, it actually overheats and the breaks loose power. I believe its the break cable since the pads, disks and callipers are new

I'm probably going to do these eventually.. To easy not too.. I did the Steeda IRS Braces and that made a huge difference in the feel..

If your car’s not lowered why do you have the lower control arms mounted in the center hole of the LCA relocation brackets? With a stock ride height they should be in the top hole according to BMR?

Still saving lives

Wow what is the sprayer set up ?

This isn’t a permanent fix. I’ve already done it

thank you !

Like your vid. But you need to brighten and focus what you are filming thanks

Thanks for this video

Can the cap not be done in 1 full piece?

When you put on a new mirror, does it have to be programmed? My car is a premium with driver assist. Thank you

Awful design on these cheep cars. I’m having such a hard time pressing the button on the connection because of the location they stuffed it in

steven wimberly did it better but definitely doing this IN GREEN

What was that clicking sound and how the fukk do you fix it? I'm about to drive mine off a cliff it's driving me nuts

I have the green and the red one. Use them all the time.

What are the bolts that hold the mirror

Focus!

Right tool for the right job was not applied today.

Just wondering why don't you let your boyfriend on camera?

What am I doing wrong? I don't understand. I have this product. It calls for 2-3oz per foam cannon container which means an additional 8-10 oz water. I used 4 oz product, 8oz water. Foamed car. Used noodle mitt to rub around and clean. Not a single bead, not a single "sheeting" result. Next day, different car, added 5 oz product to 5 oz water. Foamed car. Noodle mitt to rub around and rinse off. Not a single bead, nor sheeting occurred. Cars are rarely driven and are pretty clean with good paint and clear coats.

Careful using this stuff. Wash off and dry quick! Otherwise spots will be left behind. The spots don't come off unless you use a cloth like you're polishing. After the mistake, I found it would have been quicker just polishing. Great stuff and car looks great from a distance. Look real close and it's a lot of work coming.

3:43 like watching a monkey fuck a football

Gas cap was tight. 10+ minute "rest" was all it needed. Thanks. (Side note, this will most likely delete both driver seat "memories", so, and particularly if you use both "memory positions", memorize (I do it twice our of abundant caution) the one that is "on" when you disconnect the negative terminal, then reposition to the other position and "memorize" it. )

dude wants to keep this up against the wall in his trailer and installs a shit desk plug in that sticks out of the back 3 to 4 inches. who are you kidding with this garbage.

Fast forward to 2024 and the gas prices now a $120 to fill your tank. It was a 160 a year ago. 😅😂

Thanks for making this!

People claim they do not go high up enough

Cmon man you need a bigger tool box 😂 me too man, me too

...should have made the front flush not the back because it looks like a bad minecraft desk...

Oh what 😂 I thought I was going to to see this thing rip around