- Видео 34
- Просмотров 121 200
ScubaTech Key Largo
США
Добавлен 9 май 2012
We are an "Authorized Service Center" and Sales Retailer located in Key Largo Florida since 2012. In our prior years we were located in the Miami area teaching and servicing dive gear. We re-located to the Florida Keys to continue our passion for the scuba industry which has totaled 38 years to date. We invite you too visit our shop when in the Florida Keys.
Brands we service and sell are Aqualung, Apeks, Atomic, Sherwood, Genesis and Zeagle. Hydro testing, visual inspection and regulator service are preformed on site, everything we do is in house. In addition, we also service lots of the local Dive Centers, helping them stay up to date with their rental equipment service needs. Tank VIP Inspector Certification is also offered for more information please call the shop at 305 900-0855.
We appreciate you watching and supporting our channel please don't forget to Subscribe.
Brands we service and sell are Aqualung, Apeks, Atomic, Sherwood, Genesis and Zeagle. Hydro testing, visual inspection and regulator service are preformed on site, everything we do is in house. In addition, we also service lots of the local Dive Centers, helping them stay up to date with their rental equipment service needs. Tank VIP Inspector Certification is also offered for more information please call the shop at 305 900-0855.
We appreciate you watching and supporting our channel please don't forget to Subscribe.
How to repair a leaking scuba computer quick disconnect.
Take apart the QD for your computer and change the o rings.
Просмотров: 319
Видео
Scuba tank boots will damage your tanks!
Просмотров 1,4 тыс.8 месяцев назад
A close look at how scuba tank boots retain water and allow corrosion to build up. Boot are very popular but can be harmful as well.
Scuba regulator full of corrosion
Просмотров 58811 месяцев назад
Ultrasonic cleaning of a US Divers 1st stage full of corrosion. Before and after
Rusty HP steel 100, brushing the interior
Просмотров 1,7 тыс.Год назад
This is a follow up from a previous video, which had lots of interior rust. I brush out as much as possible and see the results.
Scubapro 1st stage with broken hose end
Просмотров 682Год назад
The HP hose broke off and left behind the thread side in the body of first stage. After others failed to remove all that was left was a soft brass nub. I had to drill out and extract the remaining nub.
How to VIP Galvanized Steel HP Scuba Tanks
Просмотров 3,5 тыс.Год назад
Steel scuba tanks are subject to rusting at a rapid pace if water is allowed to enter the cylinder. In this video I show you 3 examples of advanced rusting in galvanized steel scuba tanks are 2 years old.
Aqualung Titan Regulator before & after
Просмотров 2,3 тыс.Год назад
Aqualung Scuba regulator heavy corrosion, results after cleaning.
Steel 72 scuba tanks, should we be servicing or not
Просмотров 3,4 тыс.Год назад
Steel 72 tanks have been around since the 1950's some are ok to service and some not.
A day at Scuba Tech Key Largo
Просмотров 1,4 тыс.Год назад
Join me for a day at my shop, I have two sets of doubles to work on and a BCD, Snuba hose and hydros all in the same day.
Scuba Tank HP 3500 SP 9791 Renewed
Просмотров 624Год назад
Scuba Tanks HP 3500 has been renewed and can continue to be filled and serviced.
Sherwood Phantom Avid BCD Review
Просмотров 7952 года назад
I review the new for 2022 Sherwood Phantom Avid BCD and give you my honest opinion of the features and fit.
How to Hydro Test a scuba tank
Просмотров 21 тыс.2 года назад
I take you step by step on how we prepare and hydro test you scuba tanks.
How to Clean & service Zeagle F8 Regulator
Просмотров 3 тыс.2 года назад
Zeagle F8 regulator and BCD was lost for more than 2 days and drifted over 3 miles underwater. Cleaned and serviced back to new condition.
What happened to Luxfer Scuba Cylinders??
Просмотров 4,2 тыс.2 года назад
What happened to Luxfer Scuba Cylinders??
How to clean exterior corrosion on your Oxygen Tanks
Просмотров 2,3 тыс.2 года назад
How to clean exterior corrosion on your Oxygen Tanks
How to Change a dive computer battery "Quick Tip"
Просмотров 8 тыс.2 года назад
How to Change a dive computer battery "Quick Tip"
Less than 90 seconds!! Scuba BCD Quick Tips
Просмотров 4572 года назад
Less than 90 seconds!! Scuba BCD Quick Tips
How to Rebuild Atomic 1st stage Scuba Regulator needs service
Просмотров 10 тыс.2 года назад
How to Rebuild Atomic 1st stage Scuba Regulator needs service
Spiegel Grove wreck, diving with Scuba Tech at Horizon Divers
Просмотров 7 тыс.2 года назад
Spiegel Grove wreck, diving with Scuba Tech at Horizon Divers
No air to diver!! Scuba regulator clogged
Просмотров 1,7 тыс.2 года назад
No air to diver!! Scuba regulator clogged
Din Only? Scuba tanks for 300 bar DIN, can't use yoke style regulator
Просмотров 3 тыс.2 года назад
Din Only? Scuba tanks for 300 bar DIN, can't use yoke style regulator
My tanks are too old?? can't get them filled
Просмотров 9 тыс.2 года назад
My tanks are too old?? can't get them filled
Aqua Lung Scuba Double hose regulators
Просмотров 9026 лет назад
Aqua Lung Scuba Double hose regulators
How safe is to use a sand blaster on the aluminum tank to remove the paint without compromising our tank’s integrity?
@@DiveScapeTVa sand blaster can be too aggressive because there could be some loss of aluminum. Loss of aluminum will compromise the integrity of cylinder. A gel type paint stripper is a better option.
Again. Great video!
Great video! Tons of useful information. Thanks a lot!
@@DiveScapeTV glad to hear you found it helpful. Thanks for watching
@@scubatechkeylargo 🍻
Hi. I have brand new 2023 scuba tank which was refilled once- inside it is like new- but it has approx 5gr of oil in on the bottom which stinks with old olive oil. It was refilled once. What shall i use to clean it from oil? Are there some rust protectors you add inside tanks after cleaning from oil? I have bunch of isopropyl alcohol and denaturation water.
Oil is very difficult to remove, Dawn soap warm water, Blue Gold detergent, Simple Green Cleaner are my favorite ways of cleaning tanks. You may to also tumble with glass beads. The valve needs to be cleaned as well, by disassembly and cleaning individual parts.
This is on my bucket list! To avoid silting, you can use frog kicks.
Good content
@@stevecoffey4884 Thanks for watching!
Love it!
Dacor 2250 after tumbling etc has clean rust pock marks approx 40 percent of tank safe to full fill or partial fill 1200-1600 psi?
40% is a large amount of corrosion, anything over 20% is considered a fail. I can't recommend to continue service on that cylinder. Thanks for the question.
Disculpa tengo primera etapa MKII y un US DIVERS SPORT muy antigua y no consigo tutorías podrían ayudarme
No soy Scubapro dealer, no tengo tutorías.
Thank you ! Great information!!! I just dropped off two out dated Atomic Regulators!!
Not many outdated regs are out there, but I still see them come into my shop. If I can be of any help don't hesitate to reach out. Thanks
Very professional and simple plus educational You mention that the Hydro test is every 5 years Unfortunately In Australia the most over governed over legislated diving industry in the world I am not sure if it is the aim of the government to destroy the recreational diving industry in Australia Many dive shops are closing in Australia not due to safety but excessive bureaucracy I personally have been a Dive Instructor since 1983 I no longer teach diving in Australia I am sure the diving industry in America is as safe or safer than Australia Its a shame we have great diving If you are interested to see what we dont want for the diving industry in other parts of the world have a look at To show you how absurd this legislation is A recreational SCUBA Instructor must have a Commercial Diver medical form a dive physician Imagine if you had a dive school like I did with 50 cylinders and they have to be hydro tested every 12 months plus an eddy flow test For reference www.worksafe.qld.gov.au/your-industry/diving-and-snorkelling/diving-laws
How does this work with a let’s say a FABER hot galvanized steel with SP13488 specification? Is it tested the same way or do all galvanized cylinders done differently and only look at the REE as being pass fail?
I would like to know the same thing
@@dawktah2680I ran into a CONDEMNED issue with my FABER that has a born date of 1/19.
Faber Hot dip gal. tanks are now coming into their first hydro testing. As of the current date Faber has not published any special testing procedures other than the 10% rule. I suspect as testers fail these tanks Faber will petition DOT just like ( Worthington & PST) for special testing using REE and multiple pretest. Galvanized cylinders have a false fail on first and sometimes second test, this is why special procedures must be applied. I've made several inquiries about this issue with Faber Galvanized tanks, so far nothing.
Faber Hot dip gal. tanks are now coming into their first hydro testing. As of the current date Faber has not published any special testing procedures other than the 10% rule. I suspect as testers fail these tanks Faber will petition DOT just like ( Worthington & PST) for special testing using REE and multiple pretest. Galvanized cylinders have a false fail on first and sometimes second test, this is why special procedures must be applied. I've made several inquiries about this issue with Faber Galvanized tanks, so far nothing.
Your tank most likely had a false fail, I've seen this many times with galvanized steel.
The owner is one dive buddy I don’t want. If that’s how he/she cares for their gear I don’t want them anywhere near mine or my friends gear/life
I’ve owned my own tanks for years and none of them look as bad as those ie 1995 manufacturers date and they still look new. Someone is totally neglectful
Thanks great video you earned a subscription, have a great day Dive safe
Thanks for watching and subscription!
great video. thank you. quick question regarding the brushed tank, do you think the VIP of the tank will fit oxygen clean criteria at this point? or you would have tumbled it (and O2 clean)
No, a light tumble with O2 safe cleaner is needed.
What is the total cost of the equipment needed to conduct the hydrostatic test and what are the certifications needed to conduct those test? Thank you.
You can get those answers from Hydro-Test the company which sells and trains users on their equipment.
Awesome re-build...every dive community needs a shop like yours!
So why do dive shops charge for a hydro AND a VIP?????? When VIP is included in hydro and is of lesser value ? Greed. Simply a systematic rip-off.
What di you clear coat with!
You should not be scraping off any of the oxidation on aluminum tank. All what will happen is that the aluminum that you expose is going to interact with the oxygen in the ear and create new oxidation that's going to preferentially eat into the aluminum of the tank. With aluminum tanks leaving it be. I'm speaking about this from the perspective of the mechanical engineer.
I strongly disagree with your statement when it refers to scuba cylinders. Cylinders are a flexible container holding 3000 psi or more, which can and have been explosive when improperly inspected. Oxidation/corrosion, “lost of metal” will lead to pitting in the alloy, a single pit measuring .06 of an inch will fail the cylinder, but an structural column with the same pit can remain in service. Please keep in mind we in the scuba industry are formally trained, I personally have 40 years of training and experience we are also regulated by, Department of Transportation (DOT) Pipeline and Hazardous Materials Safety Administration (PHMSA) Compressed Gas Association (CGA) Code of Federal Regulations (CFR) and OSHA . In addition we are mandated to have continual education and certification every 3 years. Did you know the person filling or inspecting your scuba tank must be trained and certified every 3 years? (CFR180.205) Here are some quotes from our training text to help you understand our methods. “ The primary purpose of cleaning a cylinder, whether inside or out, is to ensure all metal surfaces are exposed to the inspector’s eyes”. “The entire exterior of the cylinder must be exposed to the inspector and not concealed”. “If corrosion is found on the exterior, under the coating then the entire coating should be removed”.
You the scuba tek man! Never understood boots on aluminum tanks 🤔
This video is so underrated. I love it.
i still have one of the broxton ave 'rene' tanks. it's dated 7/53. but it's only rated the typical 2150psi. my USD double-hose reg has the even later warner ave address.
That’s awesome, love to see early dive gear. The History of Diving museum in the keys started from a someone’s private collection. It’s now a popular must visit location when in the Florida Park Keys.
@@scubatechkeylargo i agree. it's a great place. we were there just 2 weeks ago.
Heading to UK from Spain to train and certify in visual tank inspections. Just been playing with an endoscope camera ... wasn't as easy as I thought to actually see the interior so maybe a mirror is better after all. great top see yoru idea on the internal devices to clean off small specks of rust. thanks for sharing your video
I hope my videos help you in your tank inspections. Good luck with your training.
Great video thank you. I rebuilt an M1 it locks at 125 and slowly drifts up to 140 but stays there and doesn’t move beyond that. Thoughts? Thank you! MB
125 to 150 is the acceptable range… slow drift is common Cycling the first such as turn off supply pressure purging and back on. Repeatedly cycling pressure will create a impression on the piston seat and should lock up IP.
Thank you for your response very much appreciated
👍
well, now i know how the neck of my tank got cracked, im thinking all this testing is just doing more harm than good. its like, do you change your oil and then drive like its a racecar
Yeah, I was literally just watching and was thinking the same thing. I went to the comments to see if anyone else was wondering how hard it is on these tanks, just to have it tested. I am trying to research tanks for paintball and pcp air rifles. I know the carbon fiber paint ball tanks are given a life span of 15 years, but I feel like getting them tested every 5 years is harder on them than just being careful with how you use them. And all the things I read on forums say they have never heard of a carbon tank failure in the field. Maybe a cheap regulator failure but never a tank. I read about a place purposely gouging a tank 50% through the side and filling it to 13,000 psi before it failed . But I don't think they are even catastrophic failures. I think it's more of a slow leak, and maybe the fibers start to unravel. I just think if you take care of them and not have them filled by amateurs that dont filter the water out or fill them up fast, they shouldn't have a catastrophic failure. No one will ever admit it, though.
Do you have a recommended o'ring grease to use? Or would any o'ring grease work?
silicone grease is best. Keep in mind all you need is to wet the ring, don't over lube it because it can slip out of place.
Excellent, What a chemical use in ultrasonic cleaner
Lawrence Factor regulator wash, it's a mild acid.
GUESS WHAT ? just two weeks ago .... a dive shop owner freaked out when I brought my three old tanks from 1979 in for visuals and I knew two needed Hydro . He was almost in tears telling me they were dangerous and they CAN"T be inspected or filled ...So I took them to another shop and they said - we know that dive shops in Florida refuse to service the older tanks BUT...YES they would service and fill them !
I'm not surprised by the shop owner's reaction, as per DOT we can still inspect, test and fill along with visual eddy test. However in Florida we've had multiple tanks rupture and seen first hand the consequence of neck cracks. It's up to the individual shop to make that decision. Thanks for the comment.
the dive shop i go to will send the tanks out for a hydro and then do a visual ! I asked why not do a visual first ??? they said thats how they do it !
I have shops that send me tanks for hydro without doing VIP first and many times I fail them before testing. Doing the VIP first makes sense, this way you can catch a fail and not even bother with sending it out.
This is amazing! got my open water mid January! hopefully i can do my advanced soon and feel comfortable enough to do this!
Glad to hear you're excited to dive the Spiegel, it's great dive. It'll take more than one dive to see it all so prepare for multiple dives.
Request video sir, can you show me, how to repair dumb valve bcd
Yes, I'll put a video together for you.
@@scubatechkeylargo thank you sir
I had a 10.4 litre 232 Bar Alloy 6061 tank (85 c.f.) fail a visual for a crack in the neck - DO NOT think that new alloys are not susceptible to load cracking, IF you leave a scuba tank full long enough it will fail at the weakest point. I now only dive steel cylinders which are looked after better than my dive computer, and IF I'm not planning to dive for 3 months or more, I leave them at 50 Bar (500 psi) so as not to put unnecessary stress on the cylinder.
Sometimes a fold in the neck can be mistaken for SLC neck crack. I've seen many shops confuse folds with SLC in 6061. I'm not saying that it can't happen but the chances are slim, an eddy current test will confirm a SLC.
Cool video. I have two of those military surplus tanks in my shop. 1943!!! Rated to 1800psi
Very cool, I'm looking out for a old oxygen surplus tank with the bushing still in place, just for my collection.
Someone on Scubaboard contacted PST after their SP expired in 2022. As they no longer are in the scuba industry the expiration isn't on their radar, but they seem to be glad to renew it when contacted. So waiting and contacting PST politely seems the best course of action.
Yes they did renew 9791, 2 months late but it's good until November 2026. I did a updated video on these tanks after seeing the renewal.
Thanks for sharing this information. Very informative and thorough, well presented.
Glad it was helpful!
Angel, I found two small air cylinders in my father’s basement,with the letters ALF CO stamped at the neck. Any clue on the manufacturer. 1800 psi. I can send a pic if needed.
I’m guessing it’s a old steel oxygen tank, send me pic of the markings, the valve and neck
Will do.
What is used as rust inhibitor?
Tnx video bro Machine name ?
Ultrasonic Cleaner, available on Amazon and eBay.
Good presentation, please can i get the information and specifications of the hydro test pump. Thank you
Brand is Hydro-Test above ground water jacket with digital scale.
Thanks for the informative video. I am here trying get a better understanding how all this works. Also I'm dabbling in a different application,. PCP for air rifles. Just purchased a carbon fiber over Aluminum tank. I have my own compressor and Have had an old retired tank laying around still holding air(Scott scba) But I will not add pressure to it at this point until I have it hydro'd (if it can be be done) The tank exterior is fine visually and I know that's as far as it goes. Reason I'm here again is Safety,. not sure if it matters, my tanks stay indoors and are not banged around. The whole 15 year thing... I'm trying to grasp,. I've seen tanks 40 yrs old holding pressure, Now that being said they could be a grenade with the pin pulled or they could last longer than I'm around(I Don't know)That's why I'm searching this information and not Just here. I'm not fond of the idea of having a hole drilled in my tank (Just Because Of A Date)and no test actually performed to justify. And I may be wrong in my thinking, and if I find that out I will change my thoughts on this. Closing thoughts: I know folks way smarter than me designed this format/platform. The other 2(TWO) factors is Safety And MONEY,. and that's what I am trying to separate if that's even possible. Now this new tank I'm getting, I will be installing the Valve and will be regularly inspecting the interior and will know how this tanks full history will be. The Scott SCBA tank I have went into burning buildings and sure it had some abuse including drops and being banged around. And again I have it Idle at this point. But it's a bit of history to me. Thank you again.
SCBA bottles are made from thin aluminum shell wrapped with carbon fiber and resin finish for strength. The lifespan of 15 years is designated by the manufacture, they believe after 15 years these bottles can weaken and no longer be trustworthy to hold pressure. These bottles easily damage, any exposed fibers is considered a weak stop. Thanks for watching... be safe.
Very cool. May I ask what the value of that very early US Divers tank would be today?
Value is up to the buyer, some folks love them, others never heard of them.
Makes sense. Just was curious about the one you had, value wise, incase I were to ever come across a tank with their original address on it@@scubatechkeylargo
Have a 72 from the early 90s get its first hydro stamp since being made in 1992
If made in the 1990s it not a 72, in the 1990s steel tanks were HP 3500 psi tank. 72 tanks haven't been made since the the 1970s. Curious what you have...
scubapro branded tank made by faber. Working pressure is 2400 but the shop gave me a plus rating on it.@@scubatechkeylargo
Very informative - thanks for sharing this info!
Glad it was helpful! Thanks for watching.
Very satisfying
Thank you
Hello, congratulations on the great technical videos. I would like to purchase an "atomic aquatics - comfort swivel hose - ss - 210cm" for my atomic-aquatics st1. Can you help me? Kind regards from Austria Andreas
Yes, I’ll look the price and get back to you.
Great, Thanks@@scubatechkeylargo
I picked up 2 tanks that are filled from a junk removal job … they are sitting in my driveway … and the recyclers won’t take them full. Im scared shitless of these things but I want to get them out of here. They aren’t that old probably 90s or so … I’m going to pick them up off the ground and put them in my shed. Im worried of them exploding.. but I know it’s extremely rare.
Check the born on date, if from 1990s or newer the risk is low. You can empty the air slowly and then they’re nothing more than aluminum container. I recycle condemned tanks, also the valve are yellow brass… more value then aluminum.
@@scubatechkeylargo thanks for the quick reply … I will check them
@@scubatechkeylargo got them emptied … one had ALOT of air the other almost nothing. I can handle them safely now … and I owe it all to you. Thanks for the confidence booster … they were from mid 90s
@@TrollHunterxXx glad to hear it worked out. Thanks for watching my channel!
100% correct.
Glad to see you agree. Thanks for watching
Are there issues with connecting a 300 bar DIN first stage to a 200 bar DIN tank valve?
No problem, the 300 DIN will fit. However the reverse will not work, a 200 bar DIN into a 300 bar valve. DINs are primary made as 300 bar, Posiedon did make a 200 DIN regulators in the 1970's which some divers still use.