Видео

I always see engravers holding it like a pencil. Do ya know anyone that grasps it in there fist an uses their thumb as a pivot like with a Dental handpiece? It certainly works well for going around corners cause You can steady your hand by putting your thumb down on the work and drawing it in an arch around with your thumb as a pivot. Do you know of any "cons" to this technique?

رائع جداً ❤

❤Cool.

Great camera setup

WOW!!!!!!

Super video, I learned a lot from it

What program are you using on your computer?

I think I heard you say you were using a wood block (3.50) which are you using a wood block or aluminum? And does it make a difference? Doesn't the bit itself grind into the block?

A micromotor will be more fitting for this type of work. It gives untroubled, smooth cutting/marking with long life. M'motors are great, heavy duty work horses. Kavo, Faro, Foredom, NSK are but inky few of these. They are used by dental technicians, jewellers engravers on professional basis. Variable speed 0-35000 rpm, with some even higher totque. gd luck.

Thanks for your helpful tips

Hm this machine ty

I found a 24" billet Jamey Jordan w/ adj. upper, table, & the industrial VS motor for $1600 that had only been used twice..... Now I'm trying to find out which dies I need to get..... If I go with the Eastwood motorized set they are around $400 for 10 of the more Popular dies.... Or would you recommend I get the Art Roll Kit from MB?? Thanks for the Info and teaching us Newbie's how to do this....

I just starting my adventure with beadrolling. This demonstration was very helpful :) Idea with projector and drawing it is a answer of my question how to do it to transfer draw on the metal. Like and sub for you :)

Does the Dremel have a wire sanding bit to remove engravings off of brass metal?

YO is that making calcium, carbon, iron sulfate, and leaving behind reinforced copper? Or is that just a surface layer of reinforced copper bonded to the inner steel? Either way that's cool

Hi Steve, Great video, thank you for making it and sharing. 👍 I've just bought a manual bead roller for some panels I have to make for the classic car build. I am a total novice as far as this skill is concerned. I do not have a table with my roller and I will be rolling steel. Do you think the same principle will work for me as regards producing a distortion free panel. I also plan to service my "new to me" roller as it feels a very slightly notchy. Kind regards Paul from 48 Spokes 🇬🇧

really good video! We need more stuff like this out there.

Diese verdammte Werbung versaut die Unterhaltung. Dafür ein Dislike.

Very helpful, thank you!

Great demonstration and share of knowledge, you won’t upset me if you post more content like this 👌

Great video, but spoiled by the unnecessary background noise.

Great information! Thanks for that. But the background music finally drove me away halfway through. It adds nothing, and I for one find it distracting.

Nice work! Great explanation. New subscriber! I don't own a bead roller... YET.

👍🦾

What chemical do you use to clean the sharpie?

I like the straight edge!

Excuse my ignorance but what are you carving on, it looks like paper?

Best demonstration ever

CUT THE CORNERS OFF.

Love the way you describe things! A video on 20 ga steel would be awesome, and also glad to see you making videos now!

great video steve

Thanks for the tips!

great video! easy to follow and very instructional

Just saw the video on Velocity road real nice work I will subscribe intrested in your work

Really informal video. I'd watch more. I just picked up a Power Bead roller. I'm just jumping in and looking for as much info for a bigger to soak up the machine. I'm a welder and fabricator I'd just really like to do more of the body panel and sheet metal work for engine bays along with some decorative art stuff to learn.

Top notch work!

Great and informative video. Just got a Mittler Bros bead roller and cant wait to use it.

Was this done with a beading die in one pass or an offset in two passes?

Very nice video , are those Nylatron art dies your using ?

Great video. You can drive in the snow! Just harder from the wrong side!

Love your videos and the work you do on the Facebook, "I love Bead Rolling" thread. Did you space out the upper and lower dies? Thanks.

Thanks for posting , looking forward to the next!

Just got a very basic bead roller for Christmas and before too long I’ll be jumping into some practice stuff. Looking to make some basic door cards with very simple bead rolling designs on them. Can you produce a video that shows a start to finish on something along those lines?

Lets see more of they car behind you! Great video!

Great video. Great content. The pressure disc, the way you did it, you also able more twisting force on it. Every step rise the panel center area hight but lower die stays at same hight. Would the twisting be less if started from middle ring first? Thx, Juhani

🔥🔥🔥

👍😎👍

Thank you for all the tips 👍👍😎👍👍

3

Where do you get a block of aluminium?