Видео

Bro you don't know how much you just helped me out

Do you have a video splicing it back in the harness

Thanks

Mine isn't going off. I knew it was too good to be true 😂 lol

Didn't work

Bought new cam positioning sensor pig tail, wires are white an black ,don't knowitch goes to mine,orange, an orange with Grey line

Cool,can u do same with cam positioning sensor

You just saved me so much stress, headaches and aggravation. I was getting cylinder 2 & cylinder 4 misfire. Haven't had the truck long, but figured the coils were bad with the truck having 140k on it. I replaced all 8 and drove for a short while and felt the hesitation come back. Check engine light began blinking and the engine power was down to where my a/c quit and power steering was cutting out. I got 3 of these clips that broke as yours did. I pushed them back on as best I could and figured it would be ok, but obviously not. Thankfully I found this video and plan to hit the junk yard on my way home today. There is a few of these in the yard there. Hopefully I can find some that are still decent enough. No way was I going to cut and splice, but figured I would have to replace the whole harness and or take it to the shop. I am so relieved that I can fix this myself. I am good with cars and almost always repair things myself, but I do not like messing with electrical because things are so finicky. Thanks again. I feel so lucky to have found a video that was the exact problem and solution in 1 short video.

Thank you so much. Just had this after replacing the battery. I thought something else was wrong.

Legend thank you so much❤

Took you 10 minutes just to get the second one off...

Maybe been asked before but what OBD reader are you suing? Great video

Why didn't you show how you got the house off in the back??

wow, the only video I have found on RUclips. My problem is that I'm not hearing any clicking noise. I didn't know that it was possible to recalibrate the blend doors so I am going to try that this afternoon before I go any further. Thank you.

This saved my life. Thanks so much!

thank you so much bro

That one behind the radio is so easy. Took me 20 minutes start to finish. Charged the customer $50 labor.

Straight to the point no bullshiet thank you

De pin kit off Amazon is definitely a must have.

TURN ONIGNITION !!!!

Thank you very much. You helped me repair a broken trim center in a boat that I’m installing a trim gauge in that never had one in it before you save me a lot of work and money.

THANK YOU! saved me a trip to a mechanic. Guess it's all to do with the electric steering needing to be repositioned/reset.

Just break the tail off the spark plug, simple as that.

Does the ECU on a 1998 Ford Explorer record misfire data for each cylinder or is this car too old for that? I can find total number of misfires on a bidirectional scanner but no cylinder number record. And I've looked in mode 6 but test 53n the misfire one, isn't available. Same issue when using a computer-based generic OBDII scanner.

My wire broke. How do I fix that? Thnx

Great video

Thanks for the video I have been wrestling with the idea of pushing the wires through the hole without removing the whole outdrive. 😮. This is a much better option...😊

Good video still helps me in 2024 tanks

After all this year, yes, it is very useful, thanks

I have 2005 f150 leriet with center console would it be that easy

My f150 is the only vehicle I’ve had that I’ve literally taken the entire interior apart over the years fixing various issues 😩

Wow, it worked like a charm

Just broke one replacing a coil pack on a 4.6 Sport Trac today. Stupid thing wouldn't lock back on, then the tab just broke right off like the one in the video.

tried this and the little pin part wont go back inside connector .The red part. mine is yellow and smaller . dont work also the wires wont seat all the way inside cuz the rubber stops wont fit back in back of connector

I was told today at a shop $545 to replace the whole wiring harness . Told them nope. Saw this what a great idea

Didn’t work

Great video! Thank you!

Hell yeah thanks this was a perfect video mi man .

I'm changing my ECU and I spray some Dielectric on the connectors (4) to help loosen things up a bit. Great video. Thanks

Thanks for your video. I changed mine too.

Thank you! Saved me a ton of time!

Thanks. I use Forscan and was looking for the method to find misfires and you Aced It!

I just saw this video i have a 03 ford focus and i need to replace all 4 of mine where can i get the new connectors?

Such a kind guy recording a video for us in the future to show this current generation how to fix issues. Thank you for your service!

Recommendations - loosen (do not remove) HVAC housing bolts to allow the whole assembly to move up which gives you additional space to simply remove the actuator. OP didn't show how much of a pain removing the actuator is without following this additional step (5mins). Also, with the whole assembly moved up, you can easily disconnect the connector from the actuator AFTER the actuator is removed and connector is fully accessible. Have fun!

Now do that for 45 minutes cuz it's been on for 140k miles. Lincoln navigator

Well ill be...that worked lol

Got it all disconnected and unscrewed and can’t get it past the duct work underneath it.

That really helped me thanks! Worked like a charm and your explanation of what to do was crystal clear and MUCH APPRECIATED!!! :)

He sound like Jack Nicholas