Видео

I changed the plugs on my 2015 Mazda 6 a few weeks ago. It was easy. Changing them on the 2020 Accord Hybrid, was just as simple. It only took me 30 minutes.

Is not that easy unplug the sensor

How do I take the electrical cable out of the clip is broken?

I have an 04 element and have the p0302 code first and now got the p0325. So they are together. Could it be the knock sensor causing the p0302 or does the p0302 cause the p0325? Or are they not related? Thanks.

Appreciate the video knocked mine out in about 25 to 30 mins. Took the longest unclipping it for me. Lmao

Ok I got a question is this considered a 3 pin alternator

But how to remove wire, can I jus pull it out with force ?? and how to get wire back ????

Thanks a lot

Does anyone know the severity of this issue. I scanned my car and it said to change the sensor as soon as possible if I had driving issues. That it could damage the main system.

Didnt show the 2hr of trying to find the hole. Lol.

It's easier and more visible if you go through the bottom. It's right above the oil filter. 🤦🏻

Great video bro. Tks

What size socket?

Do the spark plugs have to be torqued to a certain specification or just until they are tight?

No dielectric grease?

The paper towel trick to keep it from falling out was very much appreciated.🤯 U Sir are awesome 👍🏼👍🏼

What a great video! Finally, someone shows you an actual helpful tip. Thank you for not wasting my time with a bunch of BS. I didn’t need to know!

Does fixing this help with bad acceleration up hills?

i just did mine with just a ratchet, extension and 27mm socket cut some zipties that where cutting me stuck arm in there then turning it to the right and disconnected the clip got old one out with socket(little tight but just ease on it) put napkin from free donut in socket to keep new one in the socket thread it in just with the extension tighten it snug with ratchet and little LITTLE more reach in there and connect plug (any more questions as me lets get the fking thing done) i bought a $9 one off amazon and ill see if it works, i can already notice a difference in motor

Thank you!

325.00 for me

Beautiful!! Thank You

Thanks

Turning the key is just for views, dose absolutely nothing, it's disconnecting the negative terminal on the battery that does it.

I tried it this way, it sucked. I spent more than twice as much time trying to get it this way as it would have taken by the remove the intake manifold method. There were plenty of issues this didn’t warn you about, and will cause you FITS as it did me. Just one - how about if the tab on the connector isn’t in the 10 o’clock position (as it had to be for this video)? Then you can’t disconnect it the way they did. And, how are you going to get the connector reconnected when you can’t even see the connector you are trying to get between your needle nose pliers (which has to be just the right length, by the way), let alone turn it to the needed orientation to reconnect it on the new sensor? And I didn’t mention the nightmare it is when the old sensor falls out of your socket, or the socket catches on something when trying to take it out, and it comes off your extension and falls into that cavity below the knock sensor, and it can’t fall out the bottom. You have to try to get it out from there where you have no chance at getting your hand or fingers there, or any magnet ( had to Jack up the car and have a helper try to push it up from below with a skinny item, because you can’t get your hand in from underneath, either). There were other issues ( you may well need a 6 - point socket, etc.)…

took me 40 minutes trying this method and were suck, and on took me 1 hour removing manifold replacing sensor and put everything back

How did you get the blue part of the electrical connector off

Excellent! Excellent! Excellent!

Perfect!!

No way they want to charge me 600 dollars to fix this 😂

Oh shit is some fuckin bullshitttt

I have the Aveo 5 hatchback and it has a different alternator without the metal piece. I got into the job halfway before I realized it's a different alternator. Good video. Just sucks that this car has two or three different models with parts that are different including belts

I’m trying to replace this in my car and I can’t get the electrical component off. You said squeeze the clip I don’t see a clip on this thing what is it?

When ordering, what is the part number?

Do you think this could work on a 2008 Honda accord?

I can't reach the sensor there are too many wires in the way

Would u need to lub it befre u put it back in or it doesnt need to...

Great video!. Straight to the point. Thank you sir

U didn't meantion what kind of sensor u got. Is it original or ??

Thank you - i used your method to replace the Knock sensor in My Accord Type - S , i got a pattern part for about £15, and had to purchase a Torque Wrench and socket extensions bar -( but i now have these tools for life) had to get my your lad to get his small hands through the manifold and remove/replace the cable clip and position the sockets etc as My hands were to big to fit through the gaps, Rest was easy, saved approx £500 on garage quote! many thanks

Lol i just changed mine and my car wont turnover at all ... its just cranks 😫😫😫

The dealership in Mahwah, Nj told me today replacing the spark plugs on our 2014 Accord Hybrid would cost $999. I looked at the service person and she said, "There's a lot to it." Yeah. Right.

What size socket you got there bud

Thank you. Saved me over $2000 which was was quote from a mechanic that wouldn't have even fixed this problem. And I did it myself in about 2 minutes.

This video save me a lot of time trying to figure out how to get that alternator out of there. Thanks again great video. I like the little arrows that you made the point of bolts as well

About ready to tackle this job

Bro thanks for vid saved an idiot like myself

Great video. No fuss no muss...

Nicely done. If you can replace it with one hand, that gives me hope I can do it with two.

Thank you