Видео

Thank you so much man you saved my butt

Thanks for the tip

Really appreciate you taking the time to make this video. It helped me when my torque wrench stopped working. It had, like yours, twisted and therefore stopped clicking.

Music Choice is still around

Search AI Copilot and get the instructions for pins in the holes and 2 c-clamps holding the pins in all at once to remove the top.

I can't get the new seal in lol how do you get it in there properly? When I put it on the filter and push it in it just slides down and doesn't go in the bore?

This works it got our old one out

Show you a movie I used to work at the jawline tour runs. We made snap-on and Williams New Burtons your spring supposed to be greased where you're into the wrench sits on the pivot reset part and make sure your your screw is greased when you assemble it and get yourself a good calibration kit to calibrate it at 10 years experience in that company we need Williams we made some good torque wrenches. Have a good day. God bless. Amen

Is the inside diameter 1/2 inch? I would assume so?

I don't know how you came up with the 1/2" pipe trick. I tried it today and it worked flawlessly. Thanks

thank you man , i had exact same problem , you solved my problem

Thanks for sharing this , works great😊😊

If you are having trouble hitting the pipe hard enough to pull out the seal, try setting something really heavy on one side of the "T". Then hit the other side with the hammer. Awesome trick, I really appreciate it.

The pin on mine was held on with a c clip.

Thank you sir, I’ve got to the clear plastic, was wanting to replace batteries but it doesn’t look good, I’m like you if I can’t fix it than it goes to the where the die.

I've been trying to open mine for over 5 months, scared of breaking anything.....the inverter port isn't working anymore and really need a fix ... Your video just raised my fear-o-meter to 98%

I would think that a person would want to use something more linear like a dumbbell weight or something so to give it a slide hammer effect and preferably use a steel dumbbell weight as the plastic ones will just break apart but I’m sure anybody would know that

they shouldn't be out.. they should be spot on when you first buy them.. shouldn't they?

So silly question is this half inch rigid conduit or is this half inch gas pipe or half inch schedule 80 or half inch schedule 40

Thank you, your video was really helpful. Mine is all back together now and clicking.

Thanks sir for the video you share really help me out, just did it and it work great👍 just need to put the new seal in on a 2008 Silverado hopefully i dont damage the seal

Very clever and elegant invention! I will try it on my 6L45

Wow what a simple but elegant solution! It worked flawlessly I can't believe I've never heard of this trick before!

Goood! 👍

Can you put the new seal in the freezer to shrink it before putting it in the transmission?

Vine won't charge either. What a dismal device. Tried 12-volt. Didn't work. Mine does not have the four little holes

Dude incredible,this has been a pain in the butt,im so close only to be stopped by this,and i don't have an extra vehicle to go buy this stuff Ridiculous,But i will definitely share this.👍Add to this a1"-or 1"1/4 coupling and you have a slide hammer.

I got one just like that and I gave a friend a good one got the junk and it is very good

Bravo. You have made my day.

3/4inch pipe will not thread it 1/2 is too small wtf??

Very good idea I know it would’ve worked if I wouldn’t of taken off the rubber seal but I ended up using a Ellen wrench pry in side ways and it came right out

Thank You!!! It worked perfectly!

thanks for this video chuck. it really helped me. video and instructions were clear and useful 👍🏻

very helpful! I just met same problems!

BATTERY SWELLING? I get the one charge light without it charging any more. I don't have the cig charger to see if it is the cord. BUT i do see small stress cracks in the underside of the Case and notice it will not sit on the 4 corner supports on the bottom, so it looks like the battery has swelled. I'm guessing its a bad battery. Any one else have a battery swelling issue? Going to email them to see if I can get any replacement.

Genius idea! Thanks man!!

Love it!❤❤❤❤

Appreciate the time and effort you put into this video. It gave me some guidance on how to fix my telescope. I must disagree with you on the grease being the issue that caused the mounts to break. While it was most definitely a contributing factor, the root cause was poor engineering and design. I thank you again for all you did as it is helping me to repair mine.

good video!!!

Ha, I’m doing this for the first time and had the same idea about threading something into the seal - thanks for saving me the time searching for just the right size threaded object!

Thank you for making this video.

Lol , love it i do the same thing easy as pie 👍. Once you change it once you really don't need to change it all the time as long as the filter is tight on the seal its good , once the filter during a service comes off relatively easy the seal needs to be replaced.

Thanks for this video, buddy. It worked like a charm. Absolutely no contact with the bore, so there was zero scoring or scratching. Saved me a lot of grief. Cheers

Would you mind sharing the link to App you are using? Thank you.

Doesn't it have zoom? I just need to be moving the eyepieces?

Thank you Chuck!

Please tell me this binocular’s view range is 1500 yards or more than this

Thank you so much for this video, so illustrative. You saved me from quite a headache!

Where is the calibration video?

Everyone, there's a better video of how to take the cover off. I listed the link in this video's description.