Видео

Top my friend

same problem..how to repear bec. very slow round

the stator hits the magnets in the hub. maybe magnets need reglued? dont run it. fix it !

bro i cannot find middle frame if you broke middle frame what we can do

That's not a problem. Bikes make this sound while back wheel is spinning without peddaling. Its normal.

I have this noise instead ruclips.net/user/shorts9INqFi1IpqU?si=_nnIaLBDXWphKs03

"promo sm" 🤩

cassette bearing

I have a similar 2000w hub motor and when it was making this noise it was the cassette hub bearings, i have replaced them 2 or 3 times in less than 200 miles, has been a nightmare typical Chinese junk lets hope u don't have the same problem lol.

Is there anywhere online to buy replacement arms? Does the whole arm need changing or can the motor be put into a new plastic arm frame? Thanks

How can I get a set?

Same problem please help

What is useless as tits on a bull

I HAVE SOMETHING SIMMILAR HAPPENING, WHATS THE WORST THAT CAN HAPPEN? SHOULD I ORDER A NEW MOTOR?

thats the cassette u mong xD thts normal

Awesome

just need replace nylon gear

the cassette bearing is garbage

Got the same thing going on, any solutions?

I'm having the same issue. Have you found a solution?

I'm having the same problem. Have you found a solution?

Intricate gearing, cool

That’s cool bro

Great Ideas - God blessed your Mind 🙏❤ gogogo and never stop this passion !!

Du hast jetzt nicht wirklich ein Stück Klopapier lackiert und der Hauptton ist ein brummendes Furzgeräusch, bei sage und schreibe nur einer Plansequenz.. äh Kammeraeinstellung???🤣🤣😂!!!

a new generation up and coming, cool

Lovely track; would be interested to know what straights/corners etc. you used and what quantities I'd need to do this as an analogue track using the arc air powerbase please? Obviously don't need a pit lane so just ordinary track.

0,2 mm ?

👍👏👏👏

what is the program version

Nice 10 Kill game Gordon Happer

Sweet music!

There's two ways to fix this. Easiest is to separately power the LCs. Second is to solder a resistor to a pin on the micro controller on the LC pcb board. Both methods are explained in the ARC PRO board on Slot Forum International. Happy Racing!

I have a bank account. you will need to be a good time for the first one. I have spoken to you by email.

Do you have a circuit diagram or description of what you did here? I've just ordered the smart sensors but would like to build my own light gantry

Thanks guys! The 3rd lane is for a pit stop. I have a FTDI cable for the 6 car digital power base so I can connect it to laptop. Using SSDC or RCS64 software I can run fuel and tyre simulation as well as get position and lap times on the big telly! The track is a digital remake of vecbtb's original analogue track (check out slotforum dot com for further info on this if you're interested). It's about the most amount of track you can fit in to 8 by 4 feet however when you add the barriers it's slightly over by a cpl of inches ;-( I plan to make this a portable permanent layout and will get oversized MDF 9 by 5 cut in to 2 *(4.5 by 5) so I can take it down for storage and also move in a van. This is latest version and since that was taken I have added another CLC on the top level at left side so even more overtaking opportunities! i1043.photobucket.com/albums/b436/portals999/track_002_zpsc1s1cphj.jpg Pipe lagging is very cheap and easy to cut to size, I cut some 4mm plywood to support the top level and the lagging works great and looks pretty good! cheers!

Great layout!!! Have you finished the middle third lane yet?

Pipe lagging for supports ! Great idea....

nice layout whats the size? im trying to find a layout for a 8x4 board..