Видео

I did this and new door handle stays loose and door won’t open from the inside 🥺

Will Korea made regulator work on US Built Elantra?

Nice work

Great video! I'm getting ready to repair my front driver door and I watched this a couple of times. Keep up the good work!

Thumbs up

Where did you get the little white clips to mount it I got some but was the wrong size

Hello. Can you tell me pls what kind/size of screws you used to place the panel back after cutting those plastic couplers?

Would it be harder to do it to a roll up window?

فك فرش خلفي 300c AMG

Lower music volume

Thank you so much. Excellent video. Very helpful.

'Promosm'

I did this job for a client and i dont know how much to charge him and great video btw very helpful

I mean, it’s your car but it was hard to watch someone alter a classic.

hey is this the 95-5703B radio kit? also what radio do you have what size does it take i ordered the kit but dont know what radio it fits

Can't even hold the phone right.

Hello I have a m2 rexing dash cam a 2015 dodge durango with no manufacturer back up cam how do I install it thank you...

Just fixed my driver side door handle I appreciate the video saved me $1,800

Are you near my shop? I can give you a quote on my website www.roadshopaudio.com

Was just wondering what that would cost in my new 4runner it's got the back but I'd like front too

Nice job 👏

I have a 2012 e350. Same issue happened. Is there a link you can post for purchasing the part or part number? The MB dealership says I need to replace the panel at $4000!

Thanks man u made me waste no money

I have done an ignition switch 8 months pregnant on a jeep, pulled a transmission from a suburban, replaced my mass fuel sensor, rewires my cut out Benz headlights and stereo, fixed my DSL (driver steering locking mechanism that my locksmith accidentally pulled programming my new key, all of these by myself but doing my door handle on my Benz was the worst job I’ve ever done I wanted to lose my mind it was awful. Watch videos people

Seems to be a common issue with the damn German Benz

Did you disconnect the battery?

Yall want me to tell yall the secret to this door and the white clip? Its all built to install in one piece quickly on the assembly line, the door latch and plastic piece going from the window reg to the door handle are all connected by wires and plastic parts THAT CAN BREAK IF YOU'RE NOT CAREFUL. Do all the stuff shown here except for pulling the white plastic piece loose (its not easy to line back up if you do like the video. Remove three torx in the door latch. One 8mm bolt behind a grommet above the latch and pull the door key mech out. Slide the exterior door handle back and pull it out. Theres a little connector when you pull the handle back that is meant to swivel towards you. Use a small screwdriver or pick to get that connector loose. Loosen the screw that was behind the exterior door handle a few turns and push the white plastic assembly in slightly towards the inside of the door, (theres a little barb that holds it in place in the door sheet metal). Slide that towards the front of the door and then the old regulator, door latch, white clip and all will slide forward, down and out of the door. Then you rotate the latch, clip and all off the old regulator, install that to the new regulator. Route the wires through the holes in the new panel. Put the door connector end in the bottom of door, and slide the reassembled reg and latch into the door lining everything up with the door handle holes and guiding the latch into place to place a screw in to hold it and reverse the disassembly steps. The handle connector is a little tricky to plug in but not terrible. Id make a vid, but it was my nieces car and I no longer have access to it to make said video. Nor the time to disassemble it to reassemble it yet again. That white plastic clip gave me fits until i came to this realization of a process. Its so much easier to do right doing it the way I'm suggesting.

Could I Just Buy Doors With Power Windows Already On & Install That Way ?

Thank you so much, I fitted a new handle on my merc today. Your video helped a great deal. I haven’t got a dremel so just used a sharp chisel to remove the plastic rivets. I purchased a box of fixing clips of various sizes just incase some broke and there was actually one missing! Took me about 3 hours as I had no idea what I was doing until I watched your video. Thanks once again from your English buddies across the pond in London 🇬🇧👊🏼

The cameraman fucking sucks

Tbh the battery should’ve been disconnected very easy to blow a interior fuse for the radio

Good luck with that stereo, mine lasted about 18 months.

That back up camera sound, great job! If I did it I’d break secure ports accidentally and it’d be a lil wiggly haha

Link for the product

👏 it’s the lil things sometimes. Looks much better now

Kapı döşemesini söküp içten açma kolulunu degiştirmesi sadece 10 dk ama siz çok mesafeli ugraş vemişsiniz kısaca döşemenin orjinalligi gitti tirim sesi yapar içten açma kolunun altınta ufak bir delik açacaksın içten açma kolunu keseceksin pimi aşagıga dogru iteceksin kolu tak deliktenden pimi iteceksin delik olan yeride mastikle kapat iş biter

My handle snapped too like the one u did on my 2010 benz c350

Gracias a este tutorial pude arreglar la puerta de mi Mercedes 😎🎉

Is this the 10.25” or 12.3” screen?

Este video está grandiosos no entiendo mucho el inglés y gracias a ti lo pude hacer muchas gracia

Really good video that goes through the entire process to avoid any possible first time gotchas and hiccups. Well done as I was able to do this on my own C250 in less than 3 hours - taking my time to not break anything. The most difficult part was grinding the black taps as Dremel was just melting the plastic rather than cutting it off. Used a wood drill bit and just grinded it out till it broke free.

Choppy & worthless!

Great video!

Precise information. Very specific bravo good t you

I need you to do mine

Should I install an inline fuse and if so what amps? GREAT VIDEO!!!

Super merci

Very well explained I give you A+ I need to do it on my c350 you are a master pro I ll drink a modelo on your name while doing the job 👍🏼🙏🏼great video thanks

Were are u located do you know anyone in California that can do this ? Whats the average cost?

Great video. Just literally finished the job and couldn't of done it without you. Amateur/rookie at best so took me about 2.5hrs with most of the proper tools. Didn't have a small grinder had to use a 4inch disc but it works once you go slow and steady, Delighted.