Видео

I believe that's high pressure switch.

Where is the high side located?

Not simple as your video suggestion. First, not everyone has the tool like you have. Second not everyone has the same piple installation like you have. Third, not everyone has issue like your kitchen sink clogged. Finally, for my issue, I must call the plumber anyway.

What quick jack is that bc x5 have a very wide spread jack point. Thx

Great job brother I’m gonna try it on my wife’s suburban. I replaced the blow motor resistor thinking that would fix the issue. I still replaced it tho because the old one was really nasty.

You know I never thought about renting a snake.. that's a great idea in gonna dry thus tomorrow thank you

Very good video! One thing to add is take the hood back and easily rest it against the windshield. It makes it easier if the hood prop is out of the way.

I’ve never heard of stressing soldered joints to failure. Rather than spend that much time opening multiple valves, I turn on the bathroom faucet to both hot and cold. Then I Let R Rip. Then turn off the water after air is cleared. But what do I know?

What did you pull out?

…I used two plungers to unclogged my kitchen sink. A sink plunger and a toilet plunger. Sink plunger to stop outflow of one side and gently plunging the non-eurator side with the toilet plunger. It worked for now 🙋🏾‍♀️💅🏾

Thanks buddy! I followed your steps and saved my 400 bucks😛♥️ You are genies✌🏻

Just what I need it I’m installing water softener. I originally wasn’t going to install bypass by I will just in case

Not everyone has this tool at home! So many people have to call a plumber!!!!

EXCELLENT!! EXTREMELY HELPFUL!! THANK YOU!!

I just did the same with a more manual 50 foot auger. I went about 47 feet, the end was full of food. Thought I got the clog, but no luck. Guess I'll try again tomorrow.

Thank you on rhe tie rod end ❤

Fuck 😂😂😂see nothing

Do you worry about using that rental tool with older drain pipes ?

This video was very helpful, clear and well done! I tried others but useless basic information. This guy was real and I like the way he presented the the solution. Hopefully it will do the trick cause we have tried the basics.

Just used your video to this exact same thing and it worked perfectly! Thanks!!

I have the same situation with the plugging of both drains, but my plumbing does not look like that. I have the huge trap on the regular kitchen sink side but I do not have a horizontal pipe connecting to my garbage disposal. Basically, my set up is split From the wall. I always kind of knew there was some thing arising, because when I would garbage disposals a full sink full of water, it would rise up on the other side with this disgusting crud water.

I sometimes wake up with a 1.

Had my instinct for 3 weeks and it stays at 5 😂

I WILL CALL SUPER MAR8O.. 🤣👍🏼👍🏼,

Good video, my clog must be where yours is, I will try a small snake first, Thanks.

Book time calls 4hr eachside and customers dunno why it cost soo much

I have a flopping noise in my tire I was sure it was a broken steel belt or a bearing. was told that it could be the Slime tire sealant I put in it. It's like 12 or 14 oz.

Thanks great. Do I need to buy OEM expensive. Or can I just go on eBay and get the cheap one.

Great job where did you buy this tool. Please..didnt watch your full video

Thank you for the demo and mention of safeguards! Will try to unplug mine now. : )

Good video but 90% of my jobs cost $85 not $500

Anybody can help Me out ? So I pulled out the middle piece and the pipe that’s connect to the back wall had a lot of gunk in it so I removed most of it with a broken hanger but only what I could reach, but after assembling back it only worked for a second lol. Should I snake that back piece even more ?

Why are you breathing so hard?

I have the EXACT same car, same color too! I just did this to the car and I replaced everything, even all the ball joints about two weeks ago. I did driver side first and there was a learning curve, a lot of cussing, straining sounds, grunts, etc. Then I did the other side in about an hour! It’s amazing what you can do when you know what to do!

What headers

Man, I'm dealing with this exact issue. Tried a 25-foot auger, with no avail. Getting ready to go rent a 50-footer, per your suggestion....

Nice vid, you guys seem like great guys. However, With all due respect, other than fluid and a belt, all you did is remove the knuckle and somebody else did all the rest of the work displayed in the title/thumbnail. Would have liked to see a little more of that stuff.

My bathroom sink. For some reason I it only goes 3-4ft in after taking off the P-Trap. It uncloggs it but it seems I do this once a year. Spent $60 on a Rigid manual/drill snake. I live on the 2nd floor apartment/condo type. I thought I could run the snake deeper than 3-4ft. Is that normal?

My clog happened on Christmas day 2022 and where it was clogged was under the cement basement floor lucky i have a 50' snake to go down the pipe as the clean out for the pipe was 3" from the floor and when i pulled out the snake out of the pipe the snake was coved in black sludge here's a tip but the drain plugs in the sink so when you unscrew the P-Trap you only have to deal with the water in the pipes and if you have a SHOP VAC suck the water out of the sink and pipe before you unscrew the P-Trap

This is my problem but I can't take the pipe out. I have no enough strength...

Why can't you just boil some hot water and pour down the drain instead of changing the temp on your hot water heater your thermocouple might go out of wack

Not enough information about which & how to remove bolts

Once the you think the drain is cleared , I like to fill the sinks up with hot water. Once the sinks are full, pull the plug and check the speed the water drains. If the drain is truly cleared you will see a small whirlpool form and hear a sucking noise very close to the end of the emptying

Once a month, put the temperature of your hot water heater up to the highest setting. Wait 30 minutes. Turn the hot water on only, on full and let run for 5 full minutes. Afterwards, turn the hot water setting back down to the lower former desired setting.

Don’t ever apologize for teaching. :) thank you.

Got the tie rod to pop loose but couldn’t get the one on the bar to free. Torched it, used pullers, hammered on it, pry bar, nothing. I gave up and put everything back together. I feel very defeated.

I’m having the exact problem

Might not get a reply but that plug that u are talking about where would I get one? Mine is broken

That hose is a breather line onto the front diff.!👍well it is on mine anyways.😉

Did you have to recalibrate the sensor?