Видео

Ok

Nice car , but Stop it ! It's not a 10 second car . No battery shut off switch, and no roll bar ,which is needed if you run 11.40-9.99. and your rolling take off with those street tires would have gone up in smoke . You don't have the power . High 12.00 at best

My old man use to say, Criticism is reflection of frustrations ! So enjoy that awesome 67 and keep the good work 🤜🤛

What wheel and tire set up is that

Hey, nice car . You should consider doing another video on it. You mentioned how it has a ladder bar coil over suspension. I also noticed you ran the exhaust thru the trunk and out the lower quarter panel. Nice ! Could you put it on a lift and show us how and what were done. Thanks 👍 AWESOME VIDEO.

Love it !! Your plates should be TKTGTR !! Really love the way you did the two tone…

Nice car but where is the Tim slip. Definitely call this bs. I know it can be done but not this one.

Love it. The poor boy build. Good for you

I had one in 1973 in High School with a very similar motor build, dark green, cragar chrome mags . I was only able to get 12.7 second quarter mile at Orange County raceway, but that was pretty decent for bias ply tires and 289 with 302 heads, a 780CFM Holly, + Headers, balanced blueprinted, etc. Not sure on HP output, but never lost a race on the street because it had such great power / weight ratio and traction bars. LOVE this one, like mine but much more complete build and package! Beautifully Done. Brings back fond memories.

WOW!!!! Amazing work. Nicely done everyone.👍👍. Thank You for sharing your video. 🙏🏼

I’ve been searching for this video because I remember watching it years ago but i couldn’t find it but just happened to pop up on my feed lmao. Beautiful car man!!

Thats one fine build and supper clean sound.great job .now come build mine.

Awesome car

Do you still have the 67 Mustang?

Very interesting, but slow down the camera movement. I couldn't see anything, it went by so fast. It made me sick to watch all the fast camera movement. I would really like to have seen the detail on the work.

dude this looks like galavant or something, awesome stuff

This is something I need to learn lol

Killer 'Stang. How do I contact Bartolo Motorsports? I can't find them. Thank you.

Are the rear tire bigers than the front tires?

Nice I have an original 73 mach 1 ordered with this engine .... My 67 coupe is a big block car 68 is 289 coupe

too bad its not red... jk jk kool car.. saw one todsay where i work at... boss told me its a 67.... howeever minor rusts and corrosion that could be touched up and need s new paint job.. also some new lining for the bottome of the car in the inside.. sorryt i doknt know my car vocab... however the seats have good upholholstery and some minor things need to be fixed...also need a new radio... but it seems like its runs or thats what my boss said

The creativity god gave us 🥺🔥

Do a real burnout don't power brake it.then you can see if it's got muscle.

Wow looks great. I had a “67” back in high school. Just bought another one 2 weeks ago. Already have a 4.6 SOHC and a 4R70W built and ready.

What afr head and cam grind Solid lifter ? 294 or 310

I’d like to know more about the combo Clay smith cam ? What grind ? What afr heads did you use ?

dad buys your tires to

I call Bullshit. He's probably on an 1/8th mile track with a conversion card for 10.75. No way. What kind of gears and stall? Not happening. Had a 70 barracuda in the early nineties. I ran track in Savannah Ga, an Westhampton, Long Island. Mopar or no fucking car💪💯

You did a great job man, Beautiful car

I have a 66 mustang coupe with a 408 stroker with 457 rwhp and ran a best of 11.07 @ 131 mph. My car is lighter with significantly more cubes. I call BS

I've rode 9.75 @ 145 in my friend's Crower injected 427 Vega, this Mustang as represented would be lucky to break into the 11's as shown!

Spinning the tires, oh thats impressive !

I'm building my 68 coupe dropped a 351w with fmx transmission but got a long ways to go still.

Quite ironic. Usually buildings are built to keep the outside out. Looks good y'all

Dude that car is a beauty, love it!

I really hate the music. I watched this cuz i wanted to know what goes on and there was no commentary. if i want to listen to music then i'll go watch a music video

Bought a ‘66 this summer. Just ordered the 302 long block 300 hp with C4 auto and full wiring harness. Pulling out the inline 6 three speed. Looks like you new what you were doing for sure.

can you tell me the size tire and rims on it?/? did yuo have to cut the rear to install? i have a 67 fastback i just bought ,would love to put same on my car!!

Классная тачка

Perfekt and the Sound and Engine are perfekt too👍🏼👍🏼

Can I get a package deal? 😉

This whole video is bullshit! This Mustang 302 does not run 10.75 in the 1/4 mile. You need a built big block to go that fast, and the guy in the video is not poor as he claims. He is a rich actor Kirk Acevedo. I've seen him on "Band of Brothers", "OZ", "Invincible", etc. Just look up "Kirk Acevedo" on RUclips and you'll see it's the same guy.

10.75 is damn impressive!!! Nice job... 😎

A Coyote will never sound as good as a pushrod engine.

This is fascinating and I enjoyed it but… as a location scout I can tell you that I could’ve found them an existing location in eastern California or the desert of the southwest and saved them a lot of work. Sorry if I offended any of you who have made your careers in stage craft whether it’s the theater or film, I love soundstages and what can be done on them but there’s nothing quite like a real location. Do I build sets for my films? Yes but only as a last resort desperate effort, but it never occurs to me to do it that way the first time unless I am unable to control climate or sound issues.

If your movie is anytime like your camera work .......give us all a break and quit now.

Nice car but I’d have to see it run a 10.75

Sure wish you wouldn't jerk the camera around. Hard to see the process.

Nice exhaust

That idle