- Видео 15
- Просмотров 38 866
Hecks Yeah!
США
Добавлен 18 авг 2020
Learn about metal detecting with me as I teach you things that you won't ever hear anywhere else. Metal detecting is a cloud of mystery and my mission is to make everything clear.
Turn the Deus 2 11" Coil into a 9" coil or even smaller PRO TIP
Couldn't decide between the 11" or 9" coil for your Deus 2? I'll show you how to turn the 11" coil into a smaller coil so that you can have the best of both worlds.
Просмотров: 2 574
Видео
Township put a retaining pond over historical area. DEUS 2
Просмотров 3252 года назад
The local township here hauled away a historical settlement to put in a retention pond for high density apartments.
How you should hunt with the Deus 2 WORKFLOW
Просмотров 6 тыс.2 года назад
I’m going to show you how to set up your Deus 2 to be a beast and find everything that can be found.
Set Your Reactivity to ZERO On Deus 2
Просмотров 2,2 тыс.2 года назад
Here’s a short on why you should always set your reactivity to zero on the Deus 2.
Deciphering the Deus 2 programs using the manual
Просмотров 1 тыс.2 года назад
Here I will show you how to decipher the different programs in the Deus 2 user manual.
Get the Deus 2 to detect quarters
Просмотров 9732 года назад
The Deus 2 struggles in default programs and can’t detect a roll of quarters. Here’s how to fix that.
Deus 2 Fails at Quarters
Просмотров 1,6 тыс.2 года назад
Something to make you think about. Here in this video the Deus 2 struggles to detect a roll of quarters.
XP Deus 2 Deepest Program Possible
Просмотров 21 тыс.2 года назад
This will show you how to make the deepest and most powerful program on the XP Deus 2.
XP Deus 2 Unboxing
Просмотров 1462 года назад
Here is an unboxing video for the XP Deus 2 with the 11” coil. Enjoy!
How to reduce chatter and noise with the Anfibio metal detector before it drives you crazy
Просмотров 1984 года назад
Do you have an Anfibio metal detector that chatters and squeals all the time? Is it driving you crazy like it drives me crazy? Well, be sure to watch this video and see one way to quiet down the Anfibio without reducing the sensitivity setting. Hecks Yeah! Keep swinging!!
Hecks Yeah! Think you know how to use a shovel to cut plugs with metal detecting? YOU DON'T!
Просмотров 4094 года назад
Believe it or not, but a lot of people who metal detect do not know how to use a shovel to cut a plug. Then, the plug dies and there are all these dead plugs everywhere. This video will show you what you're doing wrong.
Hecks Yeah! I bet you don't carry this in your pack when you metal detect. Well, you should!
Просмотров 4434 года назад
A lot of people ask what they should carry in their pack when they metal detect. I bet no one but I will tell you this one thing that I always bring no matter what.
How to Really Get the Deep Targets with the Equinox Metal Detector
Просмотров 1,4 тыс.4 года назад
This video shows that by swinging faster you will get deeper targets. I hope this helps. Hecks yeah! Keep swinging.
Hecks Yeah! The Notka Makro Anfibio Arm Cuff is the Worst. Here's How to Fix It
Просмотров 594 года назад
I'm not sure what happened in the engineering department of makers of the Anfibio, but here's how I fixed their arm cuff so that it doesn't saw my arm off.
Swing Speed and the Anfibio Metal Detector - This Will Blow Your Mind! Find Deep Targets
Просмотров 1304 года назад
This video will show you that with the Notka Makro Anfibio metal detector, the deeper the target, the faster you need to swing. If you've been digging only shallow targets, it's because you aren't swinging fast enough. This with all the coils, including the DDs.
Yo llevo uno de los mejores programas echo por un ingeniero bueno ya probaré el tuyo aver si es verdad que aonds más que el mío asta hoy ninguno a podido superarle
Mi dispiace,ma in questo modo suona spesso....per nulla.
using tracking is risky . it dosent calculate when the best time to refresh so it might do so on a target , and this screws up everything , so i would only use it if at all on very clean ground
The filters are there for a reason knocking every filter off to gain depth would not always be the best choice 👍
That's true, but a lot of people just turn them on for "good measure" and that could be hurting them.
I made one of these programs we will see how it goes. I don’t use park program in parks I use a custom sensitive program.
Heck great information are you intending putting out some later date video info cheers
My glass eye fell asleep
Great explanation
Cant hear you talking!
Can we see some real world finds with your superJ program.
Reales, large cents, silver dimes, you name it I have found it with this program.
But how about misshaped iron and old nails? They will ring up in non ferrous scale.
Old nails ring up because they have good metal mixed in. I now use a combination of Deep HC and Relic to tell what is iron. I'll be making a video soon.
Thanks for the video. I really enjoyed that. Do you Relic hunt or mainly just park hunt? I’m still trying to figure out the absolute deepest program for Civil War relics, and I keep jumping back and forth between Beach Sensitive and Deep HC. I’ll have to give the Park program a shot.
I hunt for everything but really look for coins. I hunt mainly woods and sometimes venture out to homesites on farms. Relic mode loses depth as the item gets smaller. So it would start missing coins at 10". Deep HC does not lose depth on small items, but even with audio response maxed, items sound softer, so you can miss them.
Interesting, I would suggest to put audio response on 4 for the confirm program, because the X Y screen is relevant for more shallow targets. that way if you hear the item is deep, you can know the X Y screen is not reliable in that case.
more please...
Minelab is Russian owned company that wouldn't buy jack shit from those swines ..
what happens if you set the discrimination to 0? Does this do away with tone 1 (iron) and everything will come in at tones 2/3 if you are using a 3 tone program. Does discrimination actually affect depth. I heard that only reactivity affects depth. Thanks, Teche Ridge Digger
Great stuff
I liked that idea and tried gold all day with mono at 13khz and 17khz for my switch over program. I'm wondering why you chose general and not the "deeper" sensitive. Thanks
Give me the Original TESORO LOBO (20 khz) with the NAUTILUS DMC power (44 volts) That's all folks
Sorry but you should not be advising settings like this because these are non usable settings in the field!
Sorry but you’re wrong.
I don't understand, why do you need to turn most things off to detect, and then use a program with things turned on to check it, why not just use the things turned on programme if it does the same?
Awesome thank you very informative
The programs Relic and Goldfield are near to your program, just reduce the reactivity...
The other solution is not to buy a machine with $500.00 coils and buy a smaller coil. 😆
Having done some technical writing, I can tell you engineering is close minded about a manual written for the end user. Traditionally these products have been viewed as complete technical descriptions of the product, and they’ll view anything else as incomplete or “dumbed down.” Some companies are doing it right, but they’re the exception to the rule. And to say that every tech writer is completely uninformed about the product is inaccurate as they are usually involved in the writing of specs, internal communications, etc. during the product development cycle.
Heck yeah where you at? Waiting for any new vids. Take care bro 😎
Just have the XY screen up and you don’t need to keep swapping programs because it literally shows you that your over big iron from the direction of the line. Unless you’re over such big iron that it overloads it and gives a positive signal but that’s easy enough to hear from the way it sounds.
I understand your concept and somewhat agree with it. I do think you may have a few of the settings reversed. I would think you would want the iron volume as high as it could go. Just thinking logically by setting it to 0 you are making the processor distinguish between ferrous and non ferrous and calculating which to quiet and which to not quiet. Setting it as high as it can go would mean that the detector wouldnt care what it was, every signal would be the same volume. I don't know if that would matter with the discrimination set to -6.4 though as you have removed any iron discrimination anyway. Also I would think you would set the audio response to its highest value, this would mean that every target no matter how deep would have the same audio response. Anything lower would cause the detector to have to figure out which signals need to be higher than others due to size and or depth.
CW....he DID suggest putting the iron VOL up to 5
Thanks for the informative video! Keep ‘em coming 😁
I have now had some time to try it out! I really like the ideas. I also use general with xy-screen as confirmation prgr! I find it deep and loud and sensitive. Use it for pinpointing. Hit it very often spot on! Tried to use the Goldfield, and like it. BUT it is almost everytime very noisy😔. Dont know how to come around that. Tried frequ-scan and Groundgrab, but no effekt.... Is it the ground disturbing? Or EMI? When I compare some default prgrs like Sens or Park or Gen, with Hecksyeahs setup, I find that he has a point! Switch between his setups and some default prgrs on the same target out there! 🇸🇪👍
Just guessing but try ground stabiliser On 2, on 1 the idea is to go deeper but more chatty, reduce sensitivity down a tad, say 94 ish, high reactivity can also make machine chatter, play around with settings next time out, just my thoughts 💭 we are all different and some people love a hot open chatty machine whilst others hate it and enjoy the silence 🤣🤣🤣🥳🥳😀😀
I gave it a go. It’s very unstable and no use to me like that here in England unfortunately.
Try my super J program with confirm.
@@tgi4605 where is it buddy ?
Can you show how reactivity 0 does in heavy iron with your settings in Gold Field? My testing has confirmed that Reactivity 2.5 or greater does much better where non ferrous is next to ferrous. But maybe it is better with 0???
Low Recovery Slower Swing deepest targets?
I’ve never used park but I see why you’ve based this deep program on it. I have a Tudor coin Spill site. 3 silver coins from the 1500s they were between 8 and 10 inches. The uneven patina on the first one up suggested it had been stuck to others. Found two more 30 centimetres away. We’ve matched the uneven patina on two suggesting they were touching. The third coin has that patina too but doesn’t match the other coins. Suggesting it may have been stuck to a fourth. I’ll go back in park with all fillers off and see how I get on. Thanks 😊
Do you really want your 10" targets sound the same as your 2" targets?
Why would you ever want to make a target sound quieter, causing you to potentially miss it? Why would you ever care if any target sounded differently at 10" over 2"? Don't you dig until you find the target?
@@hecksyeah5196 Those quieter targets are the ones I dig. Just another way to discriminate surface trash. To each his own ;)
@@gwcracker I’ve found an 1829 silver half-dime,a 1858 silver seated quarter, an 1803 silver half Reale, and a 1735 copper Chinese coin 2” down.
Thanks for the heal tip- I have the 11 inch coil and I have been wanting to go smaller - now I don’t have to. I’m looking forward to trying the super J program as well. I appreciate the information you are giving me. It’s helping me to understand this incredible machine better.
Great idea...
Thank you buddy I appreciate that it opened my mind up to a lot of things Looking forward for more information thanks
I was just thinking about this today.
Turn on and go, See all your setting without scrolling thru a menu. Great detector...
Intresting, can you please make a video with using your setting vs other XpD2 setting to show the difference on both test deep targets and also live digs, really interested to see the results 😀😀😀
Good afternoon. I have not downloaded the v.7 version yet. Do you plan to and test? Thanks and still liking your program
Hi, yes. I have a Mac so I have to do goofy workaround to update it.
@@hecksyeah5196 great and super J is working very well. Looking forward to see if they detuned or made the deus hotter
@@BC-dig I just updated to 7! They added Notch for the goldfield!!! I’m going to change my superj and try to lower IAR and up notch to 30. I have an area where they dumped dirt on a pile of 1700-1800s coins, so they are 18” deep. 😭
ALSO, you never cut completely around on your plug!! Always leave an attached plug. I think that's more important than your compression theory!!
Thank u , it was helpful for me, since I am just starting to detect.
Nice I prefer the 9” over the 11”
Nice. Now you can have both, plus a 6", if you have the 11"
But the amount of falsing with a reactivity that is too low for conditions would slow you down so much that you wouldn't gain anything....no?
There’s no falsing, just more targets.
I’ll try it..
In an iron patch you’re going to lose more targets to iron masking than you find with the extra depth you’re getting by setting your reactivity to 0
That’s not the case. The Deus 2 passes the nail board test with reactivity at zero. All I do is hunt in iron patches. Old 1800s houses knocked over. If you set your reactivity to anything but zero then you’re losing targets.
@@hecksyeah5196 nail board tests are notoriously unreliable because they don’t account for variable depth. This method is going to cause confirmation bias because you’ll occasionally hit a deep signal that sounds great, and when you lose a target to masking you’ll be unaware of it. So you’ll only ever get positive feedback.
@@woodrowengle I’m sorry but I have a pile of settlement silver that says otherwise. Have you even tested? I have as well as others and the consensus with the Deus 2 is reactivity zero.
@@hecksyeah5196 come on man, you’re an engineer, approach this scientifically. You’ve found some silver. Here’s what you need to know: 1. How often would you have still detected that silver at a reactivity setting of 2 during normal use? 2. How often are you losing a signal to iron masking during normal use? You don’t know the answer to either of these things, you’re just letting a positive result confirm your beliefs.
@@woodrowengle I check all the time. I increase reactivity and the signal disappears. Deus used to have that reactivity was recovery AND transmit power in their manual. So it seems XP may have used transmit power to mimic a pseudo recovery setting.
Sad…same way in the California gold fields.
cool dude, thanks