Видео

Клас, я искал как удалить пост из платформы "Telegraph" для телеграма и я ничего не нашёл кроме этого

I think you will show how to delete my publication on telegra.ph

la persona que usa el hidraulico es muy culon yo ya lo hubiera despedido si fuera su patron es muy flojo

typical job site.. one guy working his ass off.. and two lard asses watching.

How about, some jack oil in there, it only takes a bite about 3/4of the way down.

снимать научитесь. вы что в порнухе одни разговоры вместо того, что бы бабу трахать, одни разговоры непонятные. Что в этих видео, вместо демонстрации одни разговоры.

is this the british version of the 3 stooges?

Need some solid rubber tires on that thing!

This guy must work for the city or the government.

to much hard work, like other watchers have said use a LONGER JACKING BAR makes life much easier

Water my friend

а кувалдой ёбнуть не пробовали по столбу?

O

Come on gringo!

Super gemacht .in 5 min grabt das keiner aus. Nimm nächste mal eine längerstange zum Pumpen das schont den Rücken. 2 Seitliche Schläge mit den Grossen Hammer und altes Brett dazwischen .Dann hast du es sogar in 3 minuten locker. Ich habe 50 Zaunsäulen sammt Betong gezogen . Von der Baurüstung das Seitenfenster oben eine Bootsseilwinde kostet 15 euro neu zieht bis locker 1 Tonne . 3xan der Kurbel geleiert ging auch super. Tolles Video und weiterhin viel Glück liebe Grüße andy

Super made .in 5 minutes no one digs out. Next time take a longer rod for pumping that protects the back. 2 side blows with the big hammer and old board in between. Then you have it even in 3 minutes loose. I drew 50 fence posts with Betong. From the construction armor the side window above a boat winch costs 15 euro new draws up loose 1 ton. 3xan the crank was also great. Great video and good luck best regards andy Super gemacht .in 5 min grabt das keiner aus. Nimm nächste mal eine längerstange zum Pumpen das schont den Rücken. 2 Seitliche Schläge mit den Grossen Hammer und altes Brett dazwischen .Dann hast du es sogar in 3 minuten locker. Ich habe 50 Zaunsäulen sammt Betong gezogen . Von der Baurüstung das Seitenfenster oben eine Bootsseilwinde kostet 15 euro neu zieht bis locker 1 Tonne . 3xan der Kurbel geleiert ging auch super. Tolles Video und weiterhin viel Glück liebe Grüße andy

You've Got air in your pump or it's low on oil..

You made that look SOOoooooo difficult.

it does not work,,,,may be next time...

Just use a high lift jack

I have pulled up steel posts like that. I just wrap the chain around the post and hook it to my 6' front end loader bucket on my tractor. A few pushes and pulls against that post will loosen it up. All you have to do is pull the handle on the front end loader and everything comes out of the ground. After the 1st one is finished I go to the next 200 posts. It doesn't take long at all.

Are you from the 1800's? Perhaps the term "utility pole" is what you meant to say.

Looks like a cut down engine hoist? I used my hoist to pull some posts and tree stumps,no problems.

This farm doesn't have a tractor with a 3 point? That would take two seconds to remove.

Need a 10ton jack to do 1ton work. If that's a 20ton, it needs about 40tons

No one sends telegraph messages anymore

I would have cut it off, and slipped another down the pipe.

Ineptitude short with bad sound and a guy who is no physicist. Just a waste of time.

just let my wife drive through the gate...post wiil fall over.....

Let the girl do it .....

Good job he only removed one they would have run out of daylight.

an engine hoist wil do the same thing.

junk

Pressure gauge added would show when pumping is required.

Death trap of you don't cut the top off first that way you have some control over it

Nice toy.

дауны какие то...

I wonder how he got the chain to grab the post

Dont get it !!!!! Whats the tie and suit for...

put a long pipe on that bar, bud!

I suggest you use a longer poll to pump the jack up

What was this video about? I missed it because I couldn't keep from looking at those Big Beautiful Breast's on the gal in the background. Sure would love to play with 'em and stuff….

How would it fair up pulling a strainer post driven in 4ft with a post knocker

Why not tap it with a sledge hammer when you pause .

that guy is way out of shape!

I have to give anyone credit for creating something but this is big and cumbersome when it doesn't need to be. Take a look at the SAFE JACK accessories for the Hi-Lift type jack. The parts are cheap, portable and compact by comparison. I've used it to pull posts, cemented in steel fence posts, lift heavy pumps and pulled saplings. When I'm not using it to pull something, I still have a useful tool for jacking up vehicles.

If I had a John Deere and a 3 point, this would be a no brainer. In addition, this outfit is not especially powerful using a 3 ton long stroke ram. A Hi-Lift jack and the cheap SAFE JACK accessories has all the power and would be very portable. The lift arm is very short and so it's arc swings back quickly putting a lot of bending moment on the frame.

Not sure i'd want my face that close to a chain under that much pressure

6:23-24 that's some serious overhang.!!!

thats how i felt after i got a tooth yanked..