Видео

Make sure is lock up tonight🙃👍

1981 I purchased mine and still running…made USA model 15101 many AC jobs..

you added an expansion tank on the cold line but there is a check valve coming out of the tankless so the expansion tank is not doing anything? As far as I can see. EDIT I think you said that is a strainer screen so I stand corrected. Do you still have a check valve on that cold line?

I have an opportunity to buy one of these for 20, it still works, for how long? That's the million dollar question. I'm researching what the damage would be if it were to take a dump. Are spare parts available??

What is the difference between the black CSST flexible gas line and the yellow CSST flexible gas line?

how do get parts?

Same as mine 15401 cfm = 4 ,,,,Plastics are available ,, unfortunately my pump struggles to get a vacuum despite 3x oil flushes. Next step is to strip and inspect pump section .

Is that the 15400. What size capacitor does that pump come with?

I have a robinair mo 15425..it has a large port on the top that socks air good..the bottom port has the standard fitting..it doesn't do anything..what's the bottom one for?

How do you like field piece probes I'm still using analog gauge's

where you get that condensate drain

I got inspired by this video but the issues I saw with your set up was that your set up is slightly uncomfortable..so I got the MCT veto BAG and found a way to have everything you have in your bag to fit in mine and have a light set up

12:31. "it's pretty basic" yea right .... Cool utility setup. Only thing missing is the platform bed across the back and the proverbial kitchen sink

YUP NOTICED CAP BIN HAD DIRTY HAND PRINTS

Thanks for putting out this information. Just picked up my first used Robinair 15400 today. Just out of curiosity do you know what the viscosity of the oil is that these pumps use? thanks in advance.

Great to see a loadout video with used tools and not everything German made.

Just pulled a later model (blue) one of these apart. A complete dismantle, every item except the oil seal in the case was removed. The unit had very low use but went underwater in a storm and was left as is for about 5 months. Changed a chunky bearing in the motor 6203RB and meticulously dismantled, cleaned and polished the internal surfaces of the vane pump, no so much corroded as stained and discoloured on its surface from the water sitting there mixed with the vacuum oil. there was some slight surface rust on the external surface on the pump, that to was cleaned off. I noticed on reassembly there were no dowls or the like for aligning the plates and body of the vane pump. Given the tolerances of the mounting screws and the lack of an end bearing in the pump, the whole housing was free to move slightly on the alloy face its attached to. Just seems a strange way of doing it given the shaft at the motor end just runs through an oil seal and that's it. I wonder if there is some special factory alignment pins that are then replaced by screws during assembly. Anyway it works great now sucks a serious vacuum, wish I had a manometer or Torr meter to quantify that. Just wondering if anyone else has had the vane pump apart and did anything besides align and centre the plate stack and pump body pieces visually on assembly.

Where are you located? I need this in my house

Como desarmar esta máquina por completo cuando gotea por el eje por detrás??

Veto wouldnt warranty the strap?

Amazing toolset, thanks for sharing

How and what did you use to secure the cover to the tool boxes?

I have the same pump that I'm trying to rebuild. I took all the internal apart to inspect and found a lot of rust in it. Clean it out and put it back together but it will not pump down to 2000 micron.

Очень крутая концепция. Шкаф на колесах. Единственное с чем не согласен - каждый електро инструмент должен лежать в своем чемодане. Так лучше сохраняется и с ним удобно хранить его оснастку. (быры для перфоратора, круги для болгарки...) Отношение американцев к инструменту и организации труда - образец поведения для всего мира. Стараюсь учиться у Вас ребята. Привет из Украины.

Nice to see a properly used bit of kit, half the reviews on here are shiny new with suspiciously clean tools

Awesome sweet times!

You must spend more time looking at your tools than using them

Excellent set up,!! Thanks for the tour

Do NOT forget next time to install a NEUTRALIZER

Then people questions why we charge so much, all the things we have to buy

Great video do you have a mixing valve or a thermostatic balancing valve on thr return from the radiant pipes?

Condensate is acidic, will it eat up the little pump you have in place? I install a neutralizer on condensate drain from tank-less condensing type WH's so it doesnt eat up drains and drain pipes.

Nice one

Note to self, the expansion tank is installed up side down there fore rendering it useless.

Congratulaciones, youre blessed.

Great work! Had too watch this twice. Attention to every little detail. Hat off to you sir

Who makes those pics?

Great job, Debating the need for expansion tank with my plumber.. My manual says its needed.

What is this system heating? Offices?

Great install. So clean. Also FYI there's condensate pumps with built in neutralizer media. NSP-50

Very clean job..I just only wish our installers took the care and thought out this job as you did. Can't imagine how much cash you have in propress fittings!

All I can say is that it’s just a work of art and proper work sir. Very nice work to be proud of.

Nice job great looking install! I am Wondering why you went with the condensate pump instead of just piping it over to the drain 🤔

I like the MB2, perfect for what tools I really need, yeah I hate how it tips over too, mine started to rip from the bottom and veto doesn’t cover that

Really clean install!! What kind of propress do you use for the 4” pipe?

Good video! I wish I could be a minimalist (compared to my bag, yours definitely is, lol). I will say though, I thought the shoulder straps were also warrantied? Good tips too. Thanks for sharing.

Nice setup. How did you attach the flashlight holder to the bag?

이동식 작업실이네요!대박

Nice 😎👍

its good, nothing better than working using van. i wish i could find my yellow wire nuts or a 3/8 copper 90